Wyrestorm MX-0404-HDBT-H2 User manual

4x4 HDBaseT Matrix with HDCP 2.2
and 4 Low Prole PoH Receivers (70m/230ft)
MX-0404-HDBT-H2-KIT Receivers Quickstart Guide
In the Box
Refer to the MX-0404-HDBT-H2-KIT MTRX Quickstart Guide for box
contents included with this kit.
Basic Wiring Diagram
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while
devices are powered on may cause damage. WyreStorm recommends
powering off devices before disconnecting these connections.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Before Beginning
• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
• Verify that all items are included in the packaging per the In the Box
list.
Pre Wire
1. Run a Cat5e/6/6a cable from the matrix location to the receiver
location no longer than 35m/114ft (4K) and 70m/230ft (1080p).
Terminate the cable per the HDMI/HDBaseT Wiring section.
2. (Optional) If using IR emitters, run the wire and terminate per the IR
TX (Emitter) Wiring section.
3. (Optional) If using IR receivers or an IR control system, run the wire
and terminate per the IR RX/IR EXT (Receiver) Wiring section.
Receiver Installation
1. Install the matrix switcher following the instructions provided in the
MX-0404-HDBT-H2-KIT MTRX Quickstart Guide.
2. Connect the HDMI Out on the receiver to an input on the display
using an HDMI cable from a high quality brand such as WyreStorm
Express.
3. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the HDBT In jack on the receiver.
4. (Optional) Place an IR emitter onto the display device near the
device’s IR sensor and connect the opposite end to an IR TX port.
5. (Optional) Connect an IR Receiver to the receivers IR RX port. If
using an IR control system, connect it to an IR RX port on the
receiver using the WyreStorm CAB-IR-LINK or the cable created in
Pre Wire step 2.
6. Repeat steps for additional receivers.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160719
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
WyreStorm’s latest 4x4 ‘Kit’; this PoH matrix with 4 receivers ensures compatibility with the latest 4K sources that require HDCP 2.2 encryption.

Front Panel
Rear Panel
RS-232 Mode
Switches the mode for the RS-232 port.
Normal: RS-232 HDBaseT pass-through.
Update:RS-232rmwareupdate.
Power LED Solid: The transmitter is powered On
Off: The transmitter is powered Off
Status LED Flashing: The transmitter is operating normally.
Off: The transmitter is Not operating normally.
HDCP LED
Solid: Audio and Video signal is HDCP protected.
Flashing: Audio and Video signal is not HDCP protected.
Off: No Audio and Video signal.
LINK LED Solid: Link to receiver has been established.
Flashing: Link to receiver has not been established.
Power In 5.5mm Male Barrel Jack
Connect to a 12V DC 1.5A power supply. DO NOT connect is using PoH from the matrix.
HDBT In
8-pin RJ-45 female
Connect to an HDBT Out on the matrix.
See HDMI/HDBaseT Wiring.
HDMI Out 19-pin type A HDMI female:
Supports HDMI and DVI/D (requires adapter-not included).
IR TX/RX
IR TX: 3.5mm (1/8in) Mono Plug: Connect to an IR emitter to control a local device from the matrix location via
HDBaseT.
IR RX: 3.5mm (1/8in) Stereo Plug: Connect to an IR receiver to send IR to control the matrix or device located near the
matrix via HDBaseT.
See IR Wiring.
RS-232
3-pin Screw Down Phoenix Connector
UsedtosendandreceiveRS-232signalsto/fromthesourcelocationviaHDBaseTandrmwareupdates.SeeRS-232
Wiring.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160719
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
2 of 4

HDMI/HDBaseT Wiring
IMPORTANT! HDMI/HDBaseT Wiring Guidelines
• 4K UHD resolutions require more bandwidth than 1080p, for this
reason Wyrestorm recommends using Cat6 or higher to ensure proper
4K UHD transmission.
• The use of patch panels, wall plates, cable extenders, kinks in cables,
and electrical or environmental interference can have an adverse effect
on HDMI and HDBaseT transmission limiting performance.
• If a patch panel is being used, Cat6a or higher cable must be used
from the matrix to the receiver as well as inside the panel to avoid loss
of signal.
• While similar in nature, the HDBaseT protocol is different than Ethernet
and voltages provided for PoH can be higher than those provided by
PoE. For this reason, never connect an HDBaseT link to an Ethernet
router or switch to avoid damaging the connected devices.
Wiring for HDBaseT follows the EIA T568B standard.
Pin 1
Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Resolution Distances
The type of category cable used and the distance between the matrix
and receiver can restrict the available video resolution.
Refer to Video Resolutions in the Specications table for the max
distance based on resolution.
RS-232 Wiring
The following wiring diagram shows the pinouts for the extender set.
While not shown, connect the TX (transmit) to RX (receive) pins at the
control system or PC side of the cable.
Most control systems and computers are DTE where pin 2 is RX, this can
vary from device to device. Refer to the documentation for the connected
device for pin functionally to ensure that the correct connections can be
made.
Wire colors shown follow EIA-561 standard.
Pin 1:
Pin 2:
TX (Transmit)
RX (Receive)
Pin 3: Ground (GND)
1 2 3
IR Wiring
IR TX (Emitter) Wiring
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: IR Signal
Sleeve: Ground (GND)
IR RX/IR EXT (Receiver) Wiring
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that
outputs +5V DC to power the included IR receiver.
IMPORTANT! IR TX Connection Guidelines
• 3rd party IR receivers may require a different voltage, refer to the
documentation provided with the IR receiver before making any
connections to avoid damaging the device.
• When connecting to an IR control system use the WyreStorm CAB-
IR-LINK cable to remove the sleeve +5V DC.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160719
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
3 of 4

Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit
repair, component replacement or complete product replacement in the event of malfunction. The decision to repair
or replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship
and excludes normal wear and tear or cosmetic damage.
Visit the product page located at wyrestorm.com for additional information on this product including important
technical information not provided in this document and warranty terms & conditions.
Specications
Audio and Video
Inputs 1x HDBaseT 8-pin RJ-45 female
Outputs 1x HDMI 19-pin type A
Audio Formats 2ch PCM | Up to 7.1 DTS-X and Dolby
Atmos
HDMI Resolutions
(Max)
1920x1080 @60Hz 48bit (15m/50ft)
4096x2160p @60Hz 24bit 4:2:0 (7m/23ft)
HDBaseT Resolutions
(Max)
HDMI
1920x1080p @60Hz 48bit (15m/50ft)
3840x2160p @24/25/30Hz 4:4:4 24bit
(7m/23ft)
3840x2160p @24Hz 4:2:0 HDR 30bit
(3m/9.8ft)
4096x2160p @60Hz 24bit 4:2:0 (7m/23ft)
Using Cat6/6a/7
1920x1080p @60Hz 36bit (70m/230ft)
3840x2160p @24/25/30Hz 4:4:4 24bit
(35m/115ft)
3840x2160p @24Hz 4:2:0 HDR 30bit
(35m/115ft)
4096x2160p @60Hz 4:2:0 24bit
(35m/115ft)
Color Depth 1080p: 48bit | 4K UHD: 24bit | HDR @24p:
30bit BT.2020
Maximum Pixel Clock HDMI: 600mHz | HDBaseT: 297mHz
Communication and Control
HDMI HDCP 2.2 | EDID | CEC | DVI/D with adapter
(not included)
HDBaseT 1x 8-pin RJ-45 female | HDCP 2.2 | EDID |
PoH | Bidirectional IR
IR
1x 3.5mm (1/8in) Mono – IR TX
1x 3.5mm (1/8in) Stereo – IR RX
Bidirectional over HDBaseT (IR TX/IR RX)
RS-232
1x 3-pin Screw Down Phoenix Connector |
Bidirectional over HDBaseT and Firmware
update
Power
Power Input (Optional) Input: 100~240V AC 50/60Hz
Output: 12V DC 1.5A
Max Power
Consumption 6.6W
PoH 48V 15.4W
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160719
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the matrix and HDBaseT
receivers and that both devices are powered on.
Note:
When using PoH, to power the receivers, verify that the HDBaseT cable is
properly terminated per the HDMI/HDBaseT Wiring section.
• Verify that the matrix, receiver, and display support the output
resolution of the source. Refer to Video Resolutions in the
Specications table.
• CongureEDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K
rated.
• Verify that the HDBaseT cable is properly terminated per the HDMI/
HDBaseT Wiring section.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the IR cable(s) is properly terminated. See IR Wiring.
• Verify that the IR emitter is located near the IR receiver on the device.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable
to other devices to verify functionality.
• Use a flashlight to locate the IR receiver behind any tinted panels on
the device being control.
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature -4°F ~ 158°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Maximum BTU 22.52 BTU/hr
Dimensions and Weight
Rack Units/Wall Box 1U
Height 18mm/0.71in
Width 181.7mm/7.16in
Depth 94mm/3.71in
Weight 0.4Kg/0.88lbs
Regulatory
Safety and Emission CE | FCC | RoHS