Wyrestorm SW-540-TX-W User manual

Copyright © 2021 WyreStorm Technologies | wyrestorm.com
SW-540-TX-W Quickstart Guide | 210607 UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the
installation process.
Basic Wiring Diagram
4-Input 4K HDBaseT Presentation Switcher with
Matrix Outputs, USB 2.0, Multiview & Wireless Casting
SW-540-TX-W Quickstart Guide
IMPORTANT! Installation Requirements
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
In the Box
1x SW-540-TX-W Transmitter
1x 12V 2A Power Supply (US/UK/EU/AU)
2x 4-pin Terminal Blocks
2x Mounting Brackets with Screws
1x Quickstart Guide (This Document)
KEY
HDMI
Power
HDBaseT USB 2.0
USB-C
Control
SW-540-TX-W
Local Monitor
Laptop
Laptop
Tablet with
Casting
RX-500
USB
Camera
Display Device

Setup and Conguration
The SW-540-TX-W is congured using RS-232 or IP commands for Output Resolution, and EDID. Follow these steps to properly congure the transmitter based
on the system requirement.
Note: The steps and information provided in this QSG are for basic operation of the transmitter out of the box. Refer to the SW-540-TX-W API for full
conguration settings.
1. Assign a Static IP Address to ensure proper communication on an IP Network.
2. Set EDIDs to be used at each input of the device. See Conguring Input EDIDs
Communication Settings
The SW-540-TX-W contains a web UI that can be accessed by connecting to a
network and entering the IP address. We recommend that the IP address is
changed from default before accessing the web UI for the rst time.
RS-232 and IP Settings
Baud rate: 9600
Data Bits: 8bits
Parity: None
Stop Bits: 1bit
Flow Control: None
Default IP Address DHCP
Telnet TCP Port 23
Communication Connections
RS-232 Wiring
The SW-540-TX-W uses a 3-pin RS-232 with no hardware flow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
PC Connection
Connection to a PC uses the RS-232 Control connection and requires the use
of a USB to 3-pin Port Adapter cable (CAB-USB-3PIN) in order for a port to
be provided on the PC. Note that this adaptor can be used on both v1 and v2
versions.
RS-232 Passthrough
3rd Party Device
Pin 1 12V DC Out No Connection Reserved
Pin 2 TX (Transmit) ---> To ---> RX (Receive)
Pin 3 RX (Receive) ---> To ---> TX (Transmit)
Pin 4 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
RS-232 Control
3rd Party Device
Pin 1 12V DC Out No Connection Reserved
Pin 2 TX (Transmit) ---> To ---> RX (Receive)
Pin 3 RX (Receive) ---> To ---> TX (Transmit)
Pin 4 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
Audio Connections
The audio connections use a 3.5mm (1/8in) TRS Stereo Jack.
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
Copyright © 2021 WyreStorm Technologies | wyrestorm.com
SW-540-TX-W Quickstart Guide | 210607
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable transmitters, kinks in cables,
and electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
•WyreStorm recommends using pre-terminated VGA, HDMI, DP and USB
cables due to the complexity of these connector types. Using pre-
terminated cables will ensure that these connections are accurate and will
not interfere with the performance of the product.
• This product contains a USB-C connection that can be used as an audio/
video input. When using this connection verify that the USB-C cable used
supports audio/video functionality as not all USB-C cables support this
requirement.
TLS TCP Port 24

Guide Screen
The switcher uses a Guide Screen to convey the basic connection instructions for user access.
The Guide Screen can be personalized to allow custom connection instructions on the switcher’s Web UI page.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiving device.
• Verify that all HDMI and HDBaseT connections are not loose and are
functioning properly.
• Verify that the HDBaseT cable is properly terminated following EIA568B
standard.
• Verify that the output resolution of the source and display is supported by
this transmitter.
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the IR, RS-232, and Ethernet cables are properly terminated
following the Wiring and Connections section.
Relays Not Functioning
• Verify polarity of the relay connections.
Troubleshotting Tips
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
Copyright © 2021 WyreStorm Technologies | wyrestorm.com
SW-540-TX-W Quickstart Guide | 210607
IP Address
Wi Password
Host Name
Conference Room
IP: 192.168.1.8
WiFi Pwd: 12345678
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The distance between user and products should be no less than 20cm.
We declare that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.
Manufacturer: Shen Zhen Proitav Technology Co.,Ltd
Address: 301-401, Building 16, Hejing Industrial Park, No.87, Hexiu west
Road,Heping Community, Fuhai street, Baoan District, Shenzhen, China
Accessory Manufacturer: ShenZhen Tianweixun Wireless Technology Co., Ltd
Adapter: Antenna
Address of Manufacturer: 9/F, Building 1, Guole Science and Technology Park, No. 1
Lirong Road, Dalang Street, Longhua New District, Shenzhen
Accessory Manufacturer: Dongguan NB Power Electronic Limited
Adapter: Power supply
Address of Manufacturer: No.365, South Dongkeng Road, Dongkeng Town,
Dongguan City, 523443, P. R. China
The adapter shall be installed near the equipment and shall be easily accessible.
Accessory Manufacturer: Shenzhen Ohonda Technoligy Co., LTD
Adapter: Terminal block
Address of Manufacturer: Room 609, Block D, Hongtaifu Building, Zone No.34,
Baoan District, Shenzhen
Operating temperature: 0°C to 45°C
Wi-Fi Operation Frequency: 2412MHz~2472MHz
Maximum Power: 16.74dBm(E.I.R.P.)

UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a
period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
Specications
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Audio and Video
Inputs
1x VGA In: 15-pin VGA
1x Audio In: 3.5mm (1/8in) TRS Stereo
2x HDMI In: 19-pin type A
1x USB-C
Wireless Video from Airplay or Miracast Source
Outputs
1x Mirrored HDBT Out: 8-pin RJ-45 Female
1x HDMI Out: 19-pin type A
1x HDMI Out: 19-pin type A (Output 2)
1x Audio Out: 3.5mm (1/8in) TRS Stereo
Video Encoding HDBaseT Class B
Encoding Data Rate 9.2Gbps
Mirrored Output Latency 10μs (micro seconds)
Audio Formats 2ch Analog | PCM
Video Resolutions (Max)
Video Resolutions Wired Input/Output HDBT Output Cat6/6a
VGA & Casting: 1920x1080p @60Hz 8bit VGA: 8m/26.2ft 40m/131ft (4K @30Hz)
HDMI & USB-C: 3840x2160p @30Hz 8bit 4:4:4 HDMI/USB-C: 7m/22.9ft 70m/230ft (1080p @60Hz)
Supported Standards DCI | RGB
Maximum Pixel Clock 300MHz
Communication and Control
HDMI HDMI | HDCP 2.2 | EDID | DVI/D supported with adapter (not included) | CEC
HDBaseT HDMI | HDCP 2.2 | EDID | CEC | USB | RS-232
USB
3 x USB 2.0 Type A device ports | 5v 500mA per port
2 x USB 2.0 Type B host ports (assignable)
USB bandwidth over HDBaseT limited to 190Mbps
RS-232 1x RS-232 (Control): 4-pin Phoenix | Provides 12V Power
1x RS-232 (Passthrough): 4-pin Phoenix | Provides 12V Power
Ethernet 1x 8-pin RJ-45 female (API Control)
Wireless 2 x Wi-Fi Antennas | IEEE 802.11ac | Dual-band 2.4 & 5GHz
Power
Power Supply 12V DC 2A
Max Power Consumption 24W
Environmental
Operating Temperature 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing
Storage Temperature -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing
Max BTU 82 BTU/hr
Dimensions and Weight
Rack Units/Wall Box <1U
Height 25mm/0.98in (Antennas Excluded) | 180mm/7.08in (Antennas Included)
Width 215mm/8.46in (Antennas Excluded) | 215mm/8.46in (Antennas Included)
Depth 140.2mm/5.51in (Antennas Excluded) | 180mm/7.08in (Antennas Included)
Weight 0.97kg/2.13lbs
Regulatory
Safety and Emission CE | FCC | RoHS | RCM | EAC
Copyright © 2021 WyreStorm Technologies | wyrestorm.com
SW-540-TX-W Quickstart Guide | 210607