Wyrestorm MX-0808-HDBT User manual

Thank you for choosing this WyreStorm product.
Please read these instructions carefully before installing to avoid complications later.
Instruction Manual
8 x 8 Output Full HD Matrix Switch
Part Number MX-0808-HDBT

3Technical Support: [email protected] US: [phone] EU: [phone]
CONTENTS AND INTRODUCTION
1Introduction
2Features
3Safety Precautions
4Package Contents
5Specifications
6Front Panel Description
7Rear Panel Description
8Typical Application
9Connections
10 Basic Operation
11 Basic Remote Control
12 Advanced Remote Control
13 Advanced Operation
14 Troubleshooting
15 FAQs
16 Maintenance
17 Provided Service
18 Mail-in-Service
19 Warranty
20 Warranty limits and Exclusions
21 Reference Logs
Contents
The MX-0808-HDBT is a 8x8 matrix switcher that allows
any of its 8 HDMI inputs to be routed over distance to
any combination of the 8 display outputs via UTP cable,
regardless of HDCP source encryption.
The use of HDBaseT ‘one cable’ technology enables the
MX-0808-HDBT to deliver HD audio and video, multiple control
options and high speed internet access through a single Cat
5e/6/7 cable, with a transmission distance of up to 100m (328ft)
for 1080p.
The system has versatile control, with users able to choose from
several methods of controlling the matrix – Infrared (IR) emitters
and receivers, RS232, RS485, LAN, touch screen or by using the
remote control included in the package.
The MX-0808-HDBT offers incredible flexibility and reliability
of signal distribution combined with innovative features and an
ease of use that provides solutions where HD transmission over
distance to multiple displays is required, whilst also eliminating
the need for additional control and video cables on installation,
whether in a residential or commercial setting.
Part Number MX-0808-HDBT
1. Introduction

4
Technical Support: [email protected] US: [phone] EU: [phone]
FEATURES AND SAFETY PRECAUTIONS
• Allows up to 8 HDMI audio/video devices to be independently
switched through up to 8 HDMI displays or projectors
• Each output requires a UTP receiver behind each display used:
2. Features
3. Safety Precautions
1. Do not expose this apparatus to rain, moisture, sprays,
drips or splashes and ensure that no objects containing
liquids are placed on the apparatus, including cups,
glasses and vases.
2. Do not place this unit in a confined space such as
enclosed shelving, cabinets or bookshelves. Ensure the
unit is adequately ventilated.
3. To prevent the risk of electric shock or fire hazard due to
overheating, do not cover the unit or obstruct ventilation
openings with material, newspaper, cardboard or
anything that may restrict airflow into the unit.
4. Do not install near external heat sources such as
radiators, heat registers, boilers or any device that
produces heat such as amplifiers or computers and do
not place near sources of naked flame.
5. Unplug apparatus from power supply during lightening
storms or when unused for long periods of time.
6. Protect the power cable from being walked on, pinched
or restricted in any way, especially at plug connections.
7. Only use attachments/accessories specified by the
manufacturer.
8. Units contain non-servicable parts - Refer all servicing to
qualified service personnel.
WARNING
To reduce the risk of fire, electric shock
or product damage:
• Each output features integrated single RJ45 outputs
• Reads and copies EDID from connected devices
• 3D compatible and fully supports all high denition resolutions:
1080p. 1080i, 720p
• Each output card offers RS232 pass-through
• Each port supports both HDMI and DVI signals
• Choose from seven switching modes – remote control, touch
screen, Local IR, IR call back from remote locations, RS232,
RS485, and Ethernet
• Memory function to save your matrix settings
• Touch screen/display screen previews and observes the source
• IR code edit function
• Rened for Custom Install and Home Theatre installations
• Constant HDCP preventing screen drop-outs
• Control signals can be sent from matrix to screen via 2-way IR
• Single cable solution including transmission of full
HD audio/video, RS232, 2-Way IR and Ethernet
• 1080p up to 100m (328ft) range using Cat5e/6/7 UTP
(including 3D applications)
• Fully supports 48bit Deep Colour
• HDCP compliant, EDID Management
• Totally discrete IR source control allowing easy install of
duplicate HD sources
• Accessories include: 19” rack brackets, IR receiver,
IR emitters and matrix remote control
• Open source RS232 drivers available for third
party products
• 10.2 Gbps bandwidth output capacity.
NOTE: WyreStorm reserves the right to make changes to
hardware, packaging and any accompanying documentation
without prior written notice.
HDBaseT Single
Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single
Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW

5Technical Support: [email protected] US: [phone] EU: [phone]
PACKAGE CONTENTS, SPECIFICATIONS, FRONT PANEL, REAR PANEL
• MX-0808-HDBT main unit
• Instruction manual
• CD including PC software and copy of instruction manual
• Mounting brackets
• Stylus (for touch screen)
• 1 x 100-240v AC power cable/adapter
• 1 x USB to RS232 cable
• 1 x RS232 to RS485 converter
• 1 x IR RX Receiver (larger sensor for HD display)
• 8 x IR TX Emitters (small sensor for Input source)
• 1 x MX-0808-HDBT remote control (incl. battery)
4. Package Contents
Operating Temperature
Range
-5 to +35°C (-41 to +95°C)
Operating Humidity Range 5 to 90 % RH
(no condensation)
Video Amplier Bandwidth 2.25Gbps
Input Video Signal 0.5-1.0 volts p-p
Input DDC Signal 5 volts p-p (TTL)
Maximum Single Link Range 1080p Deep Colour
Transmission distance 1080p signal up to
100m / 328ft (under perfect
transmission conditions. See
FAQ on p.19)
Video Format Supported VESA: 640x480, 800x600,
1024x768, 1280x1024,
1600x1200, 1920x1200
DTV/HDTV:
480i/576i/480p/576p/720p/
1080i/1080p
Output Video High Speed HDMI
(or ‘category 2’) See FAQ on
p.19 for details.
Power Consumption 35 Watts (max.)
Power Supply 100-240V AC
Dimensions 440mm / 17.3” (W)
140mm / 5.5” (H)
288mm / 11.3” (D)
Weight 9.7 Kg / 21.41lbs
5. Specifications
6. Front Panel
01 Touch panel
02 Remote control IR sensor
03 Power on/off switch
7. Rear Panel
04 IR extension port - for control when the Matrix is out of view,
such as in a rack or enclosed shelving system
05 DIP switch
06 RS485 port - alternative control of the matrix via RS485 cable
07 LAN port - for controlling the Matrix remotely over an IP
network
08 IR TX Emitter ports - numbered 1-8 to correspond to inputs
1-8
09 RS232 port - alternative control of the matrix via RS232 cable
10 Power cable input
11 HDMI inputs - numbered 1-8
12 IR RX Receiver ports - numbered 1-8 to connect to:
HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW
13 Ethernet port - to connect to display receiver:
HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW
14 RS232 port to connect to display receiver:
HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW
15 Link status LED - lit when UTP connection established
16 UTP output - to connect to display receiver
HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW
17 ISP port for firmware updates

6
Technical Support: [email protected] US: [phone] EU: [phone]
FRONT PANEL, REAR PANEL
01
02
03
04 05
06 07 08 09
11
HDBaseT Single
Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT
In-wall HDBaseT Single
Cat5e/6/7 Display Receiver
Part Number RX-100IR-HDBT-IW
Front Panel
Rear Panel
12
13
14
15
16
17
10

7Technical Support: [email protected] US: [phone] EU: [phone]
TYPICAL APPLICATION, CONNECTION
49ft32ft16ft 65ft 82ft 98ft 114ft 131ft147ft 164ft 196ft 229ft 262ft 295ft 328ft
15m10m5m 20m 25m 30m35m40m45m50m60m70m80m90m 100m
KEY
IR
HDMI
Cat 5e
HDMI Source
IR TX emitter
placed over or
near device
infrared sensor
IR TX jack
plugged in to
IR RX port of
Matrix
Cat5e (up to 100m 328ft)
Display
HDMI
Cable
IR RX receiver
placed discretely
on the display
with a clear line
of sight to the
infrared remote
control being
used.
1080p1080i
HDBaseT 1080p
Cat5e
5V Power
Cat 5e/6
cable
performance
8. Typical Application
9. Connection
01 Connect your HDMI input sources (such as: HD-DVD,
PS3/, XBOX360, satellite/cable, Blu-Ray etc.) to HDMI
inputs 1 – 8 of the MX-0808-HDBT MATRIX.
ATTENTION Do Not Hotplug! - Please insert and
extract cables carefully with the power SWITCHED OFF.
Connecting and disconnecting while the unit is powered
can result in damage to circuitry.
02 Attach the IR TX emitter sensor directly over the infrared
receiving area of the INPUT using the ADHESIVE
BACKING. Plug the 3.5mm jack of the IR TX into your
chosen number IR RX PORT on the rear panel of the
MATRIX.
03 ATTENTION - locate the infrared sensor on devices
by shining a flashlight onto the device facia look for a
small sensor behind the plastic. You may need to adjust
the position of the emitter after installation to achieve
best results. Sometimes moving the emitter to different
areas of the facia can improve IR performance.
04 Connect a good quality, well terminated Cat 5e/6/7 cable
with an RJ45 connector wired to 568B standard at both
ends from the UTP OUT port of the MATRIX to the UTP
IN of the DISPLAY RECEIVER. Ensure both connectors
are pushed securely into each port and supported by the
connector strain relief clip to prevent them from becoming
loose. The quality of termination for your RJ45 is essential.
Poor quality terminations lead to intermittent performance
and longer install times.
ATTENTION
We strongly recommend using the supplied
mounting brackets to secure the MATRIX and the
accompanying TRANSMITTER & DISPLAY RECEIVER
baluns. Any sudden movement of these devices could lead
to loss of picture and sound if connections become loose
or strained, resulting in unnecessary service call backs.
05 Connect the HDMI OUT of the DISPLAY RECEIVER to the
HDMI IN of the display.
06 Plug the 3.5mm jack of the IR RX receiver into the IR RX
port of the display receiver balun. Place the IR RX receiver
sensor discretely on the front of the display with care taken
to achieve a clear line of sight with the remote control to
be used. Again, you may need to adjust the position of the
receiver to achieve the best signal reception.
07 Connect the display receiver balun to the 5v power adaptor
(included with the receiver)
08 Switch on the power to your input sources, displays,
and any display receiver baluns used. Finally, power up
the MATRIX. Your MX-0808-HDBT should now be fully
connected and ready for use.
ATTENTION Remember, always switch off the matrix
before unplugging any inputs or outputs – follow last on,
first off protocol
If your IR emitters and receivers are correctly placed you
should now be able control your sources from each individual
display location.
ATTENTION If there is electrical interference or cable
bends/kinks within the set up the IR is one of the first
functions to fail. If you do not have IR control:
• Check your cables are straight with jacks rmly
connected to ports.
• Check your IR sensors are unobstructed and able to
receive infrared signals.
• Check direct sunlight on the emitters/receivers is
not affecting the infrared signal.
010203 08
04
05 06
07

8
Technical Support: [email protected] US: [phone] EU: [phone]
BASIC OPERATION
10. Basic Operation
Main Menu
All basic functions can be accessed and controlled from the touch
panel main menu below.
Switch Mode
Providing all your HDMI sources, UTP outs,
display receiver, and IR inputs and outputs
have been correctly connected, setting your
sources to the desired displays is very simple.
Just follow the tips on the right hand side of the
touch screen.
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
Alternatively, you can always return to the Main Menu by
pressing the “home” button.
2. Again, follow the prompts from the Tips box – choose
your source number – for example, your Blu-ray might be
connected to HDMI input number 3 – select and press OK.
Your selected source will now be shown on your chosen
display.
Attention – if you have previously saved a source and
display combination on either of three memory settings, you
can bypass stages 1 and 2 by pressing your saved memory
setting number. See Save Mode for details on setting.
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
Save Mode:
When you have decided on your combination of
source and display, you can save your choice by
entering the “save mode” and assigning your
selection to one of the “Memory Selection”
buttons, then pressing OK.
You can clear each memory save by pressing
“C” (clear).
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
1. Press the Switch option to select your choice of source
and display. Follow the Tips on the right hand side of the
screen and first press your OUTPUT/DISPLAY number - for
example, display number 1 – and press OK.
If you have multiple displays but only one source, you can
save time by pressing the “A” (All displays) button to
automatically select all display outputs connected to the
matrix.
Attention – if you make a mistake, press “C” (Clear) to
clear the previous number and go back a step.

9Technical Support: [email protected] US: [phone] EU: [phone]
BASIC REMOTE CONTROL AND ADVANCED REMOTE CONTROL
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
0x1d 0x0d
0x1b 0x15
0x12 0x08
0x55 0x4a
0x06 0x03
0x07 0x02
0x44 0x51
0x1e 0x1a
The MX-0808-HDBT features a simple but intuitive IR ‘Call Back’
system of control through which the matrix is able to detect and
distinguish where the remote handset is being used to allow
sources or displays to be switched accordingly. As such, the
function of handset buttons and operation differs depending on
the user’s location.
Remote Control at the Matrix end (locally)
previous / next buttons
When using the remote control locally, i.e. pointed directly at the
matrix, the previous / next buttons are used to scroll between
the input sources connected to the matrix for each individual
output display. So for example, using the previous / next
buttons for 1 allows you to select the source to be set to display
1manually. See below.
Matrix System Code Switch
In the event that two MX-0808-HDBT units are used side by side
in the rack, the matrix is capable of switching between two distinct
IR System Codes to allow control of either matrix individually via
the handset.
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
System Code Switch
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
The default System setting is 0x00 but pressing the SYSTEM
CODE button on the handset THREE TIMES rapidly activates
the alternative Matrix SYSTEM CODE 0x4e, allowing control of
the second unit. Pressing the button three times again to reverts
back to default 0x00 setting.
Please note: changing the System Code is only necessary if you
are using two identical units within close range of the IR signal. If
using in different parts of the same room it is likely that you will
not need to change the setting.
Remote control at the Display end (remotely)
When controlling the matrix remotely from the display side, the
matrix automatically detects which particular output location the
user is in and only allows the selection of sources 1-8 for that
location using the button. The right hand button will be
deactivated.
For example, if you are in the Master Bedroom with a display
connected to output 3 of the matrix, the output zone is
automatically detected so options 1-8 will correspond to sources
1-8 on the matrix. Press 1-8 to scroll through your options
as you would channels on a regular TV remote.
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
11. Basic Remote Control
12. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note, due to the differing method of control based on
location, if you are using a third party control system, learning
the control from the IR is NOT recommended as control will be
limited to scrolling up/down between inputs. For discrete source
selection you will need to import discrete hex codes for control
systems. These can be obtained through the Wyrestorm website, by
contacting our technical support or you can input them manually.
IR Call Back and Third Party Control systems
For reference: The IR is NEC and possesses a carrier wave of
38KHz with a system code of 0x00
OUTPUT
CHANNEL INPUT SELECT
1
2
3
4
5
6
7
8
To change handset battery
Pinch here and pull out
Install battery ‘+’ side
up and only use CR
2025 3V batteries. Slide
compartment back into
the handset.

10
Technical Support: [email protected] US: [phone] EU: [phone]
ADVANCED OPERATION
13. Advanced Operation
Index EDID Mode Details
1 Full copy Copy HDMI output’s EDID to
the specified input port
2 Limited copy Limited copy HDMI output’s
EDID to the specified input
port
3 Fixed 1080P-2CH Fix EDID-1080p stereo
4 Fixed 1080P-6CH Fix EDID-1080p 5.1 Audio
5 Fixed 1080P-8CH Fix EDID-1080p 7.1 Audio
6 Fixed 1080i-2CH Fix EDID-1080i stereo
Typically, unless problems with device communication through
the matrix are encountered, basic operation is all that is required.
However, the following information on advanced operation will
detail how matrix system settings can be altered or data manually
input should such problems arise.
Setting Menu
Setting mode offers 5 sub-menus to choose from:
• EDID
• LC (Long Cable Mode)
• IR (Infrared)
• EQ (Equaliser)
• RST (Factory Reset)
switch
save
observe
preview
setting
A
C
MS
EQ
M1 M2 M3
EDID Mode
The EDID Mode has 6 options available to encourage device
communication.
1. If the matrix is unable to automatically read the EDID from
an input device or display, the selection of full copy, together
with your chosen output and input number, will enable the
matrix to copy EDID from one device to the other to actively
force HDCP compatibility between them.
For example: if output 3 is selected, followed by
input 8, the EDID from output 3 will be copied to input
8.
2. As above, but the selection of Limited Copy excludes
Deep Colour from the EDID to avoid discrepancies in colour
between input and output. This can be useful if the display
still shows signs of ‘noise’ or interference. The exclusion of
Deep Colour from the EDID reduces bandwidth to allow the
signal to pass through the switch easier.
Output1 source select key code:
0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87
Output2 source select key code:
0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97
Output3 source select key code:
0xa0 0xa1 0xa2 0xa3 0xa4 0xa5 0xa6 0xa7
Output4 source select key code:
0xb0 0xb1 0xb2 0xb3 0xb4 0xb5 0xb6 0xb7
Output5 source select key code:
0xc0 0xc1 0xc2 0xc3 0xc4 0xc5 0xc6 0xc7
Output6 source select key code:
0xd0 0xd1 0xd2 0xd3 0xd4 0xd5 0xd6 0xd7
Output7 source select key code:
0xe0 0xe1 0xe2 0xe3 0xe4 0xe5 0xe6 0xe7
Output8 source select key code:
0xf0 0xf1 0xf2 0xf3 0xf4 0xf5 0xf6 0xf7
For your preference to take effect, choose EDID mode 1-6 and
press:
Follow the Tips on the right hand side and select your output port
and input port – confirmation of port selection will appear in the
bottom right. Press OK to confirm your EDID selection – the new
setting will become active on next start-up of the matrix.
CPY
On selection of a mode, a warning screen will flash up to confirm
the change made will effective from the next power up. ‘Click OK’

11 Technical Support: [email protected] US: [phone] EU: [phone]
ADVANCED OPERATION
Occasionally, issues with the conflicting audio
limits of devices may result in problems with
sound.
3. Setting the matrix to instruct inputs to only output an
embedded EDID audio limit of 1080p 2 channel (stereo)
will ensure all devices only output in 2 channel audio.
4. As above but inputs are set to output to a limit of 1080p
5.1 audio.
5. As above but inputs are set to output to a limit of 1080p
7.1 audio.
6. As above but inputs are set to output to a limit of 1080i 2
channel (stereo) audio.
For example:
Support 1080i stereo
TV2
Support 1080P stereo
Support 1080P7.1 Audio
AVR
TV1
Video: 1080i
Audio: stereo
TV2
Video: 1080i
Audio: stereo
Video: 1080i
Audio: stereo
AVR
Fix EDID
1080i-2CH
TV1
Video and Audio:
unsupported
TV2
Video: 1080P
Audio: unsupported
Video: 1080P
Audio: 7. 1
AVR
TV1
Video: unsupported
Audio: stereo
TV2
Video: 1080P
Audio: stereo
Video: 1080P
Audio: stereo
AVR
TV1
DIP: 001
Copy AVR’s
EDID
DIP: 001
Copy Tv1’s
EDID
OUTPUT
INPUT