Wyrestorm SW-0401-HDBT User manual

IMPORTANT! Installation Requirements
• Visit the product page to download the latest document version, additional
documentation, rmware, and conguration tools.
• Install the latest rmware to ensure that all features described in this
document are available during and after installation.
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• An HDBaseT receiver is required to use this product.
• See Recommended Products for guidelines on choosing a receiver.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
Recommended Products
To take full advantage of the features of this switcher, WyreStorm
recommends the following products be used to complete the installation.
RX-70-4K HDBaseT Receiver – This Class A PoH receiver can be used for
general purpose transmission where IR and RS-232 routing maybe required.
RX-70-4K-ARC HDBaseT Receiver – This Class A PoH receiver can be used
for general purpose transmission where IR and RS-232 routing or Audio
Breakout maybe required.
Note: If CEC control of displays is required, the RX-70-4K-ARC cannot be used
as it does not support this feature.
In the Box
1x SW-0401-HDBT Switcher
1x 12V DC 3A Power Supply
1x AC Power Cord with US Plug
1x AC Power Cord with UK Plug
1x AC Power Cord with EU Plug
2x 3-pin Male Phoenix Connector
1x 4-pin Male Phoenix Connector
3x 5-pin Male Phoenix Connector
2x Mounting Brackets
1x Quickstart Guide (This Document)
Additional Information
Visit the product page at wyrestorm.com for additional content regarding this
product.
• Product API for conguring control via a 3rd party control system.
• Firmware updates – We consistently improve our products and may supply
rmware updates in the future to improve the operation.
Basic Wiring Diagram
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
SW-0401-HDBT Quickstart Guide | 180104
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation
process.
4 Input Scaling Smart Switch with CEC and HDBaseT Out
SW-0401-HDBT Quickstart Guide
KEY
HDMI/DisplayPort
HDBaseT
RS-232/Serial
Analog Audio
Analog Video
WyreStorm HDBaseT
Receiver
Control System
Personal Computer
Laptop
Media Player
Video Conference Device
Amplifier

Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
HDMI/HDBaseT Wiring
IMPORTANT! HDMI/HDBaseT Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on HDMI
and Ethernet transmission limiting performance. Steps should be taken to
minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using high quality HDMI cables such as
WyreStorm Active Optical or Express to ensure the highest content
performance available.
• The type of category cable and length used can restrict the available video
resolution. While Cat5e can be used, WyreStorm recommends using Cat6
or higher to ensure the highest content performance available. See Video
Resolutions in the Specications table before determining cable type and
length.
Pin 1
Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
RS-232 Communication
Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for
pin functionally to ensure that the correct connections can be made.
See SW-0401-HDBT API located on the website for commands and conguration of communication ports.
RS-232 Switcher Control RS-232 HDBT to Zone
CEC Link Control
The CEC link allows for a hard wire contact closure connection to turn CEC On
and Off to control the standby mode of the display.
Contact In/Tally Out
Contact connections are provided to allow for switching sources and feedback
to a contact closure button on a desk or wall plate.
Audio Out
The Audio Out supports both balanced and unbalanced connections. Wiring
may vary on the 3rd party device, refer to the documentation for the device
being connected.
Balanced Connections
Unbalanced Connections
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
SW-0401-HDBT Quickstart Guide | 180104
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4

EDID/Scaler Settings
The SW-0401-HDBT handles EDID differently than other switchers and has
direct settings for EDID. When connected to a source and display the EDID is
still passed to the source, however the output of the switcher can be scaled to
match the resolution of the display and maintain the highest output from the
sources. This allows for HD sources to be scaled up to UHD and UHD sources
to be scaled down to maintain a consistent picture quality.
EDID/Scaler Dial
Scaling Resolution Rotary Switch
Auto Scaling 0
1024x768p @60Hz 1
1280x720p @60Hz 2
1280x800p @60Hz 3
1366x768p @60Hz 4
1600x1200p @60Hz 5
1920x1080p @60Hz 6
1920x1200p @60Hz 7
3840x2160p @30Hz 8
API Control 9
Audio De-Embed/Control Method
The SW-0401-HDBT has modes available to control how the audio is handled
from the source HDMI, how sources are switched, and how CEC controls
display standby. These are congured via a 4 position dip switch as dened in
the table.
Mode Selection
Function Operation
Audio De-Embed
Switch 1
Audio De-Embedded from
HDMI Out (Default) - OFF
No Function - On
Source Selection Mode
Switch 2
Auto and Manual Switching
Enabled (Default) - OFF
Manual Switching Only - On
CEC Control
Switch 3
Auto and Manual CEC Con-
trol (Default) - OFF
Manual CEC Control Only
Control Method
Switch 4
API and Manual Control
(Default) - OFF
Manual Control Only - On
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to all devices in the system and that they are powered On.
• Verify that all source and HDBaseT connections are not loose and are functioning properly.
• Verify that all HDMI/HDBaseT Wiring is properly terminated.
• Verify that the EDID/Scaler Settings are set to a resolution that the display can receive.
• Verify that the switcher, receiving device, and display support the output resolution of the source.
Refer to Video Resolutions (Max) in the Specications table.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
• Use a ashlight to locate the IR receiver behind any tinted panels on the device being control
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
SW-0401-HDBT Quickstart Guide | 180104
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4

Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit repair,
component replacement or complete product replacement in the event of malfunction. The decision to repair or replace will
be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal
wear and tear or cosmetic damage. Visit the product page located at wyrestorm.com for additional information on this
product including important technical information not provided in this document and warranty terms & conditions.
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
SW-0401-HDBT Quickstart Guide | 180104
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Specications
Audio and Video
Inputs
1x VGA In: 15-pin Component Video
1x DP In: DisplayPort 1.3
2x HDMI In: 19-pin type A
Outputs
1x HDMI Out: 19-pin type A
1x HDBT Out (Class A): 8-pin RJ-45 Female
1x Audio Out (Analog): 5-pin Phoenix
Output Video Encoding HDBaseT Class A
Encoding Data Rate 9.2Gbps
End to End Latency 10μs
Audio Formats 2ch PCM | Multichannel: Up to Dolby Digital and DTS 5.1ch
Video Resolutions (Max)
HDMI/DisplayPort
1920x1080p @60Hz 12bit (15m/49ft)
1920x1200p @60Hz 12bit (15m/49ft)
3840x2160p @30Hz 4:4:4 8bit (7m/23ft)
Using Cat6
1920x1080p @30Hz 12bit (100m/328ft)
1920x1200p @60Hz 12bit (100m/328ft)
3840x2160p @30Hz 4:4:4 8bit (70m/230ft)
Using Cat6a/7
1920x1080p @30Hz 12bit (100m/328ft)
1920x1200p @60Hz 12bit (100m/328ft)
3840x2160p @30Hz 4:4:4 8bit (100m/328ft)
Color Depth 1080p: 12bit | 4K: 8bit
Maximum Pixel Clock 297MHz
Communication and Control
HDMI HDMI 1.4 | HDCP 1.4 | EDID | CEC | DVI/D supported with adapter (not included)
HDBaseT HDMI 1.4 | HDCP 1.4 | EDID | CEC | RS-232 | Ethernet
Contact Closures 1x Tally Out: 5-pin Phoenix | 1x Contact In: 5-pin Phoenix
RS-232 1x RS-232 (Switcher): 4-pin Phoenix | 1x RS-232 (HDBT): 3-pin Phoenix (Bidirectional)
Ethernet 1x Ethernet: 8-pin RJ-45 Female | 10/100Mbps | Bidirectional over HDBaseT
CEC Link 1x CEC Link: 3-pin Phoenix
Power
Power Supply 12V DC 3A
PoH IEEE 802.3af 15.4W
Max Power Consumption 22w (Includes PoH)
Environmental
Operating Temperature 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing
Storage Temperature -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing
Maximum BTU 76 BTU/hr
Dimensions and Weight
Rack Units/Wall Box <1U
Heigh 21mm/0.83in
Width 220mm/8.67in
Depth 164.2mm/6.47in
Weight 0.82kg/1.8lbs
Regulatory
Safety and Emission CE | FCC | RoHS
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.