XAC xCL AT-170 Series User manual

d
INSTALLATION GUIDE
D ESKTOP /M OBILE P AYMENT T ERMINAL
X
CL_AT
-
170
SERIES
xCL_AT-170 series
- xCL_AT-170-R-18U
- xCL_AT-170-R-18E
Before using the device, lease full charge the battery
To kee the device in good condition

1. PACKAGE CONTENT
2. DEVICE OVERVIEW
AT-170 Key Buttons & Interface Ports (Figure 1)
Figure 1
FRONT
REAR
 AT-170
 Power adaptor
(Optiona )
 USB cab e
(Optiona )
 Paper Ro
Right
 Hand Strap
(Optiona )
This symbo is intended to a ert the user before starting using the POS.

RONT AREA
1 7” Touch Disp ay
2 Printer Paper Cover & Contact ess Card Tapping Area
3 Camera for barcode scanning (Optiona )
4 Smart Card Reader (SCR) s ot
5 Audio Jack
REAR AREA 6 Battery Compartment
7 Charging Contact
RIGHT SIDE 8 Magnetic Strip Reader (MSR) s ot
9 Power Button (Press > 3 seconds to power on/off)
10 USB OTG port (type C)
■ AT-170 Power spec
Input: 5V DC, 2A
■ Power Adapter spec
Input: 100 ~240 Vac
Output: 5V DC, 2A
Caution Use on y the AC adapter approved and provided by XAC Automation
Corporation for use with this device. Use of any other AC adapter may cause a risk of
fire or exp osion.
■ Operating Temperature
0
o
C to 40
o
C
3. POWER ON/OFF THE DEVICE
Power ON – Press and ho d the Power key for 3 seconds unti the screen is activated.
(Figure 2)
Power OFF -- Press and ho d the Power key for 3 seconds to shut down the device.
Figure 2

NOTE
1. When device is in id e or suspend mode, short press power button wi wake up the
device.
2. When device require to forced shut down, press and ho d the power button for 10
seconds
4. USING THE MAGNETIC CARD READER
Swipe the card through the s ot with magnetic stripe at the back side of the card.
(Figure 3)
Figure 3
5. USING THE IC CARD READER
Insert an IC card into the s ot with the chip side facing upward (Figure 4).
Figure 4

6. USING THE KEY PAD
After inserting the chip card, press the numeric keys of virtua keypad (Figure 5, as
reference) shown on the disp ay to enter the password. Press Cance (X) key to
terminate any current function and press the Enter (O) key to confirm a va ue or an
option.
Figure 5
7. USING THE CONTACTLESS CARD READER
Tap the contact ess card on top of the contact ess ogo which is shown on the paper
cover. The 4 green LED indicates the contact ess card reading status.(Figure 6).
Figure 6
8. CHANGE THE BATTERY
STEP 1: Remove the 2 screws and open the battery cover as Figure 7.
STEP 2: Lift the battery and pu up the battery connector from device as Figure 8
STEP 3: Insert the connector of new battery into the device as Figure 8
Note: Please ensure the orientation of connector of battery cable matches the connector on
the device.
STEP 4: P ace the new battery into the compartment

STEP 5: P ace the battery cover to c ose the compartment as Figure 7.
STEP 6 Fasten the 2 screws.
Figure 7 Figure 8
Bottom Cover Removal Warning
When removing the bottom cover and screws for the purposes of changing battery, remember to
put back the cover and screws before power on the POS.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Warning for internal battery pack
To reduce risk of fire or burns:
1. Do not attempt to open, disassemb e, or service the battery pack.
2. Do not crush, puncture, short externa contacts, or dispose of in fire or water.
3. Do not heat above 60
o
C
9. INSERT SAM & SIM CARD
After removing the battery cover, two SAM and two SIM card s ot are top of the battery
(Figure 9). P ease insert the card correct y as the icon shown on the cover:
Figure 9

10. LOADING THE PAPER
STEP 1: Gent y pop the printer cover’s atch; then pu the cover upward to open the
paper ro cover (Figure 10).
STEP 2: Load a ro of therma paper into the printer. P ease ensure the printing-side of
the paper wi feed out facing the operator.
STEP 3: C ose the cover by pressing on the center of the printer cover. Use the serrated
bar to tear off any excess paper.
Figure 10
11. INSTALL THE STRAP
A ign two ends of strap pin to the notches on AT-170 rear cover as Figure 11-1.
Figure 11-1
Press downward the strap pin into the notches, than pu another pin of the strap to
insta another side as Figure 11-2.
Note After pressing the pin, make sure it is fixed into the notch of AT-170 as Figure
11-3.

Figure 11-2 Figure 11-3
Finished ook of the strap assemb y is as Figure 11-4.
Figure 11-4
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This device comp ies with Part 15 of the FCC Ru es. Operation is subject to the fo owing two
conditions: (1) This device may not cause harmfu interference, and (2) this device must accept any
interference received, inc uding interference that may cause undesired operation.
Note: This equipment has been tested and found to comp y with the imits for a C ass B digita device,
pursuant to Part 15 of the FCC Ru es. These imits are designed to provide reasonab e protection
against harmfu interference in a residentia insta ation. This equipment generates, uses and can
radiate radio frequency energy and, if not insta ed and used in accordance with the instructions, may
cause harmfu interference to radio communications. However, there is no guarantee that
interference wi not occur in a particu ar insta ation. If this equipment does cause harmfu
interference to radio or te evision reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the fo owing measures:
- Reorient or re ocate the receiving antenna.
- Increase the separation between the equipment and receiver.

- Connect the equipment into an out et on a circuit different from that to which the receiver is
connected.
- Consu t the dea er or an experienced radio/TV technician for he p.
FCC Caution: Any changes or modifications not express y approved by the party responsib e for
comp iance cou d void the user's authority to operate this equipment.
This transmitter must not be co- ocated or operating in conjunction with any other antenna or
transmitter.
R ADIATION E XPOSURE S TATEMENT :
The product comp y with the FCC portab e RF exposure imit set forth for an uncontro ed
environment and are safe for intended operation as described in this manua . The further RF
exposure reduction can be achieved if the product can be kept as far as possib e from the user body
or set the device to ower output power if such function is avai ab e.
Specific Absorption Rate (SAR) Testing Your device has been designed to comp y with app icab e
imits for RF exposure. These imits use a unit of measurement ca ed Specific Absorption Rate, or SAR,
which refers to the rate at which the body absorbs RF energy.
The Federa communications commission (FCC) has estab ished a SAR imit for head/body exposure
condition of 1.6W/kg and
extremity (hand) exposure condition of 4.0W/kg, which app ies in the United States and other
countries that fo ow the FCC’s
SAR imit.
SAR testing is conducted with the device p aced in common operating positions (e.g., he d against
the head, worn on the body) and transmitting at its highest certified power eve in each frequency
band of operation. Because the device is transmitting at its highest certified power eve , SAR tests
capture a worst-case operating scenario and therefore often do not ref ect the amount of RF
exposure during norma , everyday use.
More information on SAR testing is avai ab e on the FCC’s website at http://www.fcc.gov/guides/
wire ess-devices-and-hea th-concerns.
XAC Automation Corporation submitted SAR test resu ts demonstrating comp iance with the FCC’s
SAR imit for wire ess devices as part of the FCC’s equipment certification process for this device.
These resu ts can be accessed via the FCC’s equipment authorization database (found
at http://transition.fcc.gov/oet/ea/fccid/) by searching for the device’s FCC ID: MQT-AT170R18U.
Industry Canada Statement
This device comp ies with ISED’s icence-exempt RSSs. Operation is subject to the
fo owing two conditions: (1) This device may not cause harmfu interference, and (2) this
device must accept any interference received, inc uding interference that may cause
undesired operation.
Le présent apparei est conforme aux CNR d’ ISED app icab es aux apparei s radio exempts
de icence. L’exp oitation est autorisée aux deux conditions suivantes : (1) e dispositif ne
doit pas produire de broui age préjudiciab e, et (2) ce dispositif doit accepter tout
broui age reçu, y compris un broui age susceptib e de provoquer un fonctionnement
indésirab e.
Radiation Exposure Statement
The product comp y with the Canada portab e RF exposure imit set forth for an uncontro ed
environment and are safe for intended operation as described in this manua . The further RF
exposure reduction can be achieved if the product can be kept as far as possib e from the user body

or set the device to ower output power if such function is avai ab e.
Déclaration d'exposition aux radiations Le produit est conforme aux imites d'exposition pour es
apparei s portab es RF pour es Etats-Unis et e Canada étab ies pour un environnement non contrô é.
Le produit est sûr pour un fonctionnement te que décrit dans ce manue . La réduction aux
expositions RF peut être augmentée si 'apparei peut être conservé aussi oin que possib e du corps
de 'uti isateur ou que e dispositif est rég é sur a puissance de sortie a p us faib e si une te e
fonction est disponib e.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent is otropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
The exposure standard emp oys a unit of measurement known as the Specific Absorption Rate (SAR).
The SAR imit of head/body
and extremity (hand) exposure condition set by the ISED are 1.6 W/kg and 4.0W/kg, respective y. The
highest SAR va ue for the EUT
as reported to the ISED when hand extremity exposure condition, as described in this user guide is
2.14W/kg.
La norme d'exposition pour l'émetteur sans fil utilise une unité de mesure connue sous le nom de taux
d'absorption spécifique, ou SAR. La limite SAR fixée par l'IC est de 1,6 W / kg.
La valeur SAR la plus élevée pour l'EUT signalée à l'IC lorsqu'elle est portée sur le corps, comme décrit dans
ce guide de l'utilisateur, est de 2.14 W / kg.
I NDUSTRY C ANADA
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.
The Equipment Authorization Certification for xCL_AT-170-R-18U is listed under the following identifiers:
ISED Idenitifier: 6692A-AT170R18U Granted to XAC Automation Corporation
La certification d'autorisation d'équipement pour xCL_AT-170-R-18U est répertoriée sous es
identifiants suivants: ISED Identificateur: 6692A-AT170R18U Accordée à XAC Automation
Corporation
The above information is the exc usive inte ectua property of XAC Automation Corporation and sha not be
disc osed, distributed or reproduced without permission of XAC Automation Corporation.
XAC AUTOMATION CORP. sha not be he d iab e for technica and editoria omissions or errors made herein; nor
for incidenta or consequentia damages resu ting from the furnishing, performance or use of his materia .
XAC Automation Corporation
886-3-577-2738
www.xac.com.tw