XAC xCL AP-10 User manual

d






I NS
T
L
A
X

T
ALLATI
O
A
PAYME
N
X
CL
_
A
P
O
N G UID
E
N
T DEVICE
P
-
1
0
E

1. PACKAGE CONTENT
2. DEVICE OVERVIEW

xCL_AP‐10(hereundercalledAP‐10)KeyButtons&InterfacePorts(Figure1):
Figure1
FRONTAREA1 4” TFT Color Display (480 x 800 pixel)
2 Rubber Keypad
3 Smart Card Reader (SCR) slot
4 Magnetic Strip Reader (MSR) slot
REARAREA5 USB cable (type A)
6 SAM Compartment
■AP-10 power spec:
zPowerInput:5VDC,2Aor5VDC,1A(onlyforDUALUSB‐A)
zOperatingTemperature:0oCto40oC

FRONTREAR
xCL_AP-10 Privacy Shield (Optional)

WA
C
C

3. P OWE
R

Topowe
terminal
Note:Af
t
po
w
4. U SING
T

Swipeth
display.(
RNING:
1.Theequipmenti
s
trainingorexperie
n
energiesandenergy
2.Theequipmentis
portthatthatoutp
u
60950‐1/EN60590
‐
C
aution:UseonlytheA
C
withthisdevice
C
aution:Riskofexplosi
o
batteryaccordin
g
R
O N /O FF THE
D
ronthedevice,ple
orPOS.
t
erbootingupAP‐10,
w
ersavingmode.Ple
a
T
HE M AGNETIC
ecardthroughthe
s
Figure2)
s
intendedtobeinstall
n
ceintheequipment
magnitudesusedinth
e
intendedtobesupplie
d
u
tcomplieswithther
e
‐
1/UL60590‐1/CSA6
0
C
adapterapprovedand
o
nifthebatteryisrepl
a
g
totheinstructions.
D
EVICE
aseplugtheUSBc
a
i
f
isnoactiononAP
‐
a
seshortpressanyb
C ARD R EADE
R
s
lotwithmagnetics
Figure2
edbyskilledpersono
r
technology,particularl
e
equipmentandhostd
e
d
byahostdevice(PC
o
e
quirementoftheLim
0
950‐1
providedbyXACAuto
m
a
cedbyanincorrectty
p
a
bletypeAintothe
‐
10after60seconds,
uttononkeypadto
w
R
s
tripesidefacingth
e
r
servicepersonwhoh
a
yinknowingthevari
o
e
vice.
o
rterminaldevice)via
U
itedPowerSourceof
m
ationCorporationfor
u
p
e.Pleasedisposeofu
s
USBportofyourh
o
thedevicewillenter
w
akeupthedevice.
e
samedirectionas
t
a
ve
o
us
U
SB
IEC
u
se
s
ed
o
st
t
he

5. USING THE IC CARD READER

InsertanICcardintotheslot(Figure3)withthechipsidefacingupwardasthedisplay(Figure
4).

Figure3Figure4

6. USING THE KEY PAD

Afterinsertingthechipcard,Pressthenumerickeyasbelowkeypad(Figure5)toenterthe
desirablenumbers.PressCancel(X)keytoterminateanycurrentoperationorpresstheEnter
(O)keytoconfirmavalueoranoption.
Figure5
7. USING THE CONTACTLESS CARD READER

Tapthecontactlesscardontopofthecontactlesslogo(Figure6).

Figure6

9. INSERT SIM &SAM CARD
ToremovetheSAMcardcompartmentbyunlockingthescrewM1.6*3pieces,pleaseusethe
screwdrivertype0(Figure7),
Afterremovingthecover,theusercanfindSAM*2slotsatthebottomsideofdevice.Please
insertthecardcorrectlyastheiconshownonthecover(Figure8):








Figure7Figure8

9. INSTALL PRIVACY SHIELD (OPTIONAL ACCESSORY)
PleaserefertoFigure9for2stepstoinstalltheshield:
Step1:AlignandinserttwohooksofprivacyshieldwiththeslotonAP‐10device(filledby
rubber).
Step2:Pushdownthebottomsideofshieldtocombinewiththedevice.Andtheoutlook
isthesameasFigure10.
Figure9Figure10

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RadiationExposureStatement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and
are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved
if the product can be kept as far as possible from the user body or set the device to lower output power if such
function is available.



















The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be
disclosed, distributed or reproduced without permission of XAC Automation Corporation.
XAC Automation Corporation
886-3-577-2738