XAC XCE-25-C User manual

d
CHIP AND PIN MOBILE PAYMENT DEVICE XCE-25-C
INSTALLATION GUIDE

1. B EFORE S TARTING
There is a micro USB port (Figure 1) covered under the protection cover (Figure 2); this port is
used for battery charging, debugging, firm are update and key injection.
NOTE: The battery of xCE-25-C is built-in and rechargeable.
Figure 1 Figure 2
Operating Temperature: 0
o
C to 40
o
C
Battery Pack: 3.7V, 1050mAh
Input: 5V, 500mA
2. P OWER O N /O FF THE D EVICE
To po er on the device, press and hold the Po er key for five seconds until the green LED
light flashes and the screen sho s ords. Once it is po ered on, the LED ill blink every five
seconds to indicate it is active.
To po er off the device, press and hold the Po er key for five seconds until the screen
become blank.
Figure 3
NOTE: xCE-25-C ill po er off itself automatically if unused for 5 minutes.

3. C ONNECTING TO S MART D EVICES
Once xCE-25-C is po ered on Bluetooth ill be searchable. From the smart device’s Bluetooth
settings, pair and connect to xCE-25-C.
4. U SING THE M AGNETIC C ARD R EADER
Find the magnetic card reader slot on the right side of the device (Figure 4). S ipe the card
through the slot ith magnetic stripe side facing the same direction as the keypad (Figure 5).
Figure 4 Figure 5
5. U SING THE IC C ARD R EADER
Find the IC card reader slot on the bottom of the device (Figure 6). Insert an IC card into the
slot ith the chip side facing the same direction as the keypad (Figure 7).
Figure 6 Figure 7
6. U SING THE K EY P AD
Press Cancel(X) key to terminate any current function and press the Enter(O) key to confirm a
value or an option. Press the numeric key to enter the desirable numbers. Press the letter B
should press 2 number key t ice, then the screen displays “B” (Figure 8).
Figure 8

7. U SING THE C ONTACTLESS C ARD R EADER
Contactless reader antenna is around the display and PIN pad. It ill light up ith LED signal
hen terminal is po ered on and that means reader is orking normally. Put contactless card
to approach the antenna of card reader (Figure 9) for reading the card data during transaction.
Figure 9

Federal Communication Commission Interference Statement
This device complies ith Part 15 of the FCC Rules. Operation is subject
to the follo ing t o conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply ith the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance ith the instructions, may cause harmful interference to
radio communications. Ho ever, there is no guarantee that
interference ill not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, hich
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the follo ing
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation bet een the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to hich the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.

This transmitter must not be co-located or operating in conjunction ith
any other antenna or transmitter.
Radiation Exposure Statement:
The product comply ith the FCC portable RF exposure limit set forth for
an uncontrolled environment and are safe for intended operation as
described in this manual. The further RF exposure reduction can be
achieved if the product can be kept as far as possible from the user body
or set the device to lo er output po er if such function is available.
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed,
distributed or reproduced without permission of XAC Automation Corporation.
XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for
incidental or consequential damages resulting from the furnishing, performance or use of his material.
XAC Automation Corporation
886-3-577-2738
www.xac.com.tw