XENO 4CH User manual

XHDAR Full HD DVR
User manual

User’s Manual | 2
Safety Information
Before You Begin
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to local
codes.
This manual provides installation and operation information. To use this document, you must
have the following minimum qualifications:
 A basic knowledge of CCTV systems and components
 A basic knowledge of electrical wiring and low-voltage electrical connections
Intended use
Only use this product for its designated purpose; refer to the product specification and you
documentation.
Customer Support
For assistance in installing, operating, maintaining and troubleshooting this product refer to this
document and any other documentation provided. If you still have questions, please contact
Norbain Technical Support and Sales:
Norbain SD, 210 Wharfedale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TP, England.
UK [phone]
Note: You should be at the equipment and ready with detailsbefore calling Technical Support.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following warning, CAUTION and Note
statements identify potential hazards that can occur if the equipment is not handled properly:
* Warning:
Improper use of this equipment can cause severe bodily injury or equipment
damage.
** Caution:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
This apparatus is manufactured to comply with the radio interference.
A Declaration of Conformity in accordance with the following EU standards has
been made. The manufacturer declares that the product supplied with this
document is compliant the provisions of the EMC Directive 2004/108/EC, the CE
Marking Directive 93/68 EEC and all associated amendments.
All lead-free products offered by the company comply with the requirements of
the European law on the Restriction of Hazardous Substances (RoHS) directive:
2011/65/EU, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.

3 | Full HD Digital Video Recorder
The crossed-out wheeled bin mark symbolizes that within the European Union the
product must be collected separately at the product end-of-life. This applies to your
product and any peripherals marked with this symbol. Do not dispose of these
products as unsorted municipal waste.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
NORBAIN SD reserves the right to make changes to the product and specification of the product
from time to time without prior notice.
WARNINGS AND CAUTIONS:
To reduce the risk of fire or electric shock, do not insert any metallic objects through the
ventilation grills or other openings on the equipment.

User’s Manual | 4
Contents
CHAPTER 1:DVR USER MANUAL
1GETTING STARTED 6
1.1 Checking Supplied Items 6
1.2 Connecting Peripheral Device 7
1.3 System Startup and Shutdown 10
2EXPLANATION FOR EACH FUNCTION 12
2.1 Front Panel 12
2.2 Rear Panel 13
3OPERATION 15
3.1 User Log-in 15
3.2 Live Display Mode 16
3.3 PTZ Operation 21
3.4 Playback of Recorded Video 22
3.5 Search Recording Image 22
3.6 DST Setting 28
3.7 Screen Saver 29
4SETTING 30
4.1 System 31
4.2 Device 37
4.3 Record 42
4.4 Network 45
4.5 Backup 50
4.6 Quick Setup 52
5WEB SURVEILLANCE 53
5.1 Web Login 53
5.2 Web Configuration 54
5.3 Web monitoring 56
5.4 Web Playback 59

5 | Full HD Digital Video Recorder
CHAPTER 2:CMS CLIENT SOFTWARE USER MANUAL
6CMS USER GUIDE 61
6.1 PC REQUIREMENT 61
6.2 INSTALL 61
6.3 UNINSTALL 64
6.4 BASIC OPERATION 65
6.5 CMS FUNCTIONS 75
6.6 CMS SETUP 81
CHAPTER 3:MAC ACS CLIENT SOFTWARE USER MANUAL
7MAC ACS USER GUIDE 88
7.1 System Requirement 88
7.2 Install 88
7.3 Basic Operation 90
CHAPTER 4:MOBILE PHONE SOFTWARE USER MANUAL
8MOBILE PHONE SOFTWARE USER GUIDE 98
8.1 iPhone application software 98
8.2 Android application software 108
APPENDIX :DYNDNS SITE REGISTRATION 118
APPENDIX :NETWORK SETUP FOR EXTERNAL USAGE 121
APPENDIX :SPECIFICATION 122

User’s Manual | 6
Chapter 1
DVR USER MANUAL

7 | Full HD Digital Video Recorder
1GETTING STARTED
1.1 Checking Supplied Items
Make sure that you have the following items supplied with your DVR. If any of these items are missing or damaged, notify
your vendor immediately. Keep the packing utilities for moving or storage purposes afterwards.
Items
Photo
Quantity
Quick Start Guide 1 Set
CD (Manual & Software) 1 Set
12V DC Adaptor
Power Cable
1 Set
USB Mouse 1 Set
Screws
1 Set

User’s Manual | 8
1.2 Connecting Peripheral Device
This section describes how to connect peripheral devices efficiently to the DVR.
Install the DVR on flat surface. If required, attach a rubber mount for installation. If a 19-inch rack is used with 1.5U Height
case, it is recommend to install the system on a shelf and use 2.5~3U (1U=1.75 inch or 4.45 cm) space for proper ventilation.
4ch (1 HDD Case) Dimensions: 11.0” W x 1.9” H x 9.6” D
8ch (1 HDD Case) Dimensions: 11.0”W x 1.9”H x 9.6”D
NOTE
Install the system in a location with good ventilation to prevent overheating.

9 | Full HD Digital Video Recorder
8ch (2 HDD Case) Dimensions: 14.1” W x 2.6” H x 14” D
16ch (2 HDD Case) Dimensions: 14.1” W x 2.6” H x 14” D
WARNING !
※When connecting power cord to the system, it is strongly recommended first to plug the power cord
to the system and then plug the other side of power cord into the wall socket.

User’s Manual | 10
CAMERA CONNECTION
Example 1) All TVI 4CHs 1080P/720P support
Example 2) All AHD 4CHs 1080P/720P support
Example 3) All Analog 960H 4CHs
NOTE
In order to set TVI or AHD at the same time, the channel combination must be
2 pairs used. (1,2 CH + 3,4 CH + 5,6 CH + 7,8 CH...)
Example 4) CH 1 : TVI 1080P/720P, CH2 : TVI 1080P/720P
CH 3 : AHD 1080P/720P, CH4 : AHD 1080P/720P or Analog 960H
Example 5) CH 1 : AHD 1080P/720P, CH2 : AHD 1080P/720P or Analog 960H
CH 3 : TVI 1080P/720P, CH4 : TVI 1080P/720P

11 | Full HD Digital Video Recorder
1.3 System Startup and Shutdown
1.3.1 System Startup
After connecting peripheral devices such as cameras, monitors and a mouse to the DVR, power up the DVR by connecting
DC12V 3A adaptor to the power jack on the rear panel. The boot log will display as shown below. Please wait until the boot
process completes.
Login with ‘User Name’at the login window which will appear as shown below.
There is only one Administrator Account configurable in the DVR system. It is assigned with an unchangeable User ID
marked as ‘admin’. The default password is empty (No Password). Administrator account has full access to the DVR and its
configurable parameters. The Administrator Account also has the ability to create new users and to assign rights to the new
user accounts. Those new users created by ‘admin’account can also login with a specific password set by ‘admin’account.
N
OTE
Do not forget the administrator’s password that was set for the first time. In case the password is lost,
contact your vendor.
N
OTE
The mouse is included. In case you need to replace it, it is highly recommended to choose well-known
major brands such as DELL, MICROSOFT, LOGITECH, or SAMSUNG.

User’s Manual | 12
1.3.2 System Shutdown and change password
Option 1. Click the Shutdown button and input password on pop-up to power off the DVR
Option 2. Click the right button on the mouse and select the Shut Down to power off the DVR.
N
OTE
It is not recommended to disconnect the power cable abruptly from the back of the DVR because it may
affect the DVR and Hard Drive.
The default password for ‘admin’account is none. Therefore, just click ‘Enter’button on the dial pad. If you changed the
password for ‘admin’account, please type in the changed password to login.
N
OTE
User can type in the password using the virtual keyboard or the numeric buttons on the IR remote
controller.

13 | Full HD Digital Video Recorder
2 EXPLANATION FOR EACH FUNCTION
2.1 Front Panel
4/8/16ch DVR Front Panel (1 HDD Case)
8/16ch DVR Front Panel (2 HDD Case)
No.
Items
Functions
1
LED Indicator
Indicate System Status
Power, Record, Network
2
USB Port
USB Port (Ver. 2.0) for Mouse Operation, Backup Device or Firmware Update

User’s Manual | 14
2.2 Rear Panel
4ch (1 HDD Case) Rear Panel
8ch (1 HDD Case) Rear Panel

15 | Full HD Digital Video Recorder
8ch (2 HDD Case) Rear Panel
16ch (2 HDD Case) Rear Panel
No.
Name
Description
1
Video-In
Camera inputs (Supports NTSC/PAL)
2
Audio-In
Audio Input Device (with Amplifier)
3
Audio-Out
Audio Output Device (with Amplifier)
4
USB Port
USB 2.0 Port for Mouse Operation, Backup Device, or Firmware Update
5
HD OUTPUT
HD OUTPUT
6
LAN Port
1 x 10/100/1000M
7
Power Input
4ch : 12V 2A
8ch(1 HDD) : 12V 3A
8/16ch(2HDD) : 12V 5A
8
Alarm Output
Alarm Output
9
Sensor Input
Sensor Input
10
RS-485 Port
PTZ Dome Camera or External Keyboard Controller connection
Note
Carefully check whether the specifications of the peripheral devices match the DVR’s specifications.

User’s Manual | 16
3OPERATION
3.1 User Log-in
The DVR has various setting categories. The administrator can set the system password and <User> to prevent
unauthorized changes to setting values and alteration of recorded file.
Enter the <Admin> or <User> password which had been set by using the virtual keyboard.
N
OTE
1) <LOGIN> window will be permanently displayed in monitor as above picture until user logs in with the
right ID and password.
2) If it is set as Auto Log-In, DVR does not require LOG-IN. (Please refer to 4.1.2 User.)

17 | Full HD Digital Video Recorder
3.2 Live Display Mode
3.2.1 Full HD(1080p) Live Display
Full HD Live Display can be supported in live mode by using its HD output.
NOTE
In playback mode, the maximum resolution is 1080P.
<Full HD Live Display>

User’s Manual | 18
3.2.2 Channel Selection
Channel selection can be done by following one of the steps below:
1. CH1~CH16 buttons in the IR Remote Control.
2. 1~16 virtual buttons at the bottom of the GUI display.
The display mode can be changed by pressing the ‘MODE’ button on the DVR’s front panel.
The live images can be displayed in real-time in 1, 4, 9, 16 screen splits. Whenever the left/right arrow button on the front
panel or IR remote controller is pressed, the screen will be sequentially changed.
[1 Ch] [4 Ch]
[9 Ch] [16 Ch]
To select channel by mouse, click target channel single time to display in full screen. To return to previous display mode,
click the screen again.
To view the pop-up menu, right click anywhere on the display screen.
NOTE
To properly select a channel using the mouse, the user is required to perform a slow and clear click of the
left mouse button.

19 | Full HD Digital Video Recorder
3.2.3 Icons
The live mode display’s icons or messages will be indicated on the screen to indicate the system mode or status.
Below are the icon categories that are indicated on the monitor:
Icon to be shown
at Left-upper corner on each channel screen
Icon to be shown
at Left-bottom corner on full screen.
Continuous Recording
Sequence display on
Motion Detection Recording
Digital zoom on
Sensor Activating Recording
Audio Channel
Continuous+ Motion Recording
Continuous + Sensor Activating
Recording
Emergency Recording
N
OTE
If you cannot find any colored-mark in the top right corner of the live screen mode, then it means that the
system does not record any image. In this case, you need to check recording schedule or camera of the
main setup menu.
The sliding menu for display will be appeared when mouse cursor move into bottom and right click of mouse enale to access
pop-up-menu.
To show the menu bar, move the mouse’s cursor to the
bottom of the screen. The menu bar will be displayed.
To hide the menu bar, move the mouse’s cursor away
from the menu bar.
Menu Bar
Menu button. When pressed, System Setup, Search, Backup, Logout will appear.
Screen split options- Select from single channel, 4 channel, 9 channel, or 16 channel display.
Sequence- if pressed, the system will start displaying all the channels in sequence mode. To
stop, press the button again, or right click on the screen and select ‘SEQUENCE’
CH. Buttons- view a specifc channel in full screen mode.
Instant (emergency) recording- The system will record video based on the panic record
settings (Default: 15FPS @ 1080P).
PTZ mode- Control any supported PTZ cameras by moving the mouse pointer.
Go to Instant playback.
HDD usage indicator- Indicates the percentage of your HDD being used. If it shows 60%, then
60% of HDD space has been used.

User’s Manual | 20
3.2.4 Pop-up Menu
User can click the right button of the mouse to pop up sub-menu as shown below.
DISPLAY- Select the display split from the available options:
- 1 Screen- Single channel. Automatically displays CH1. If 1 Screen is selected again, next chronological channel will be
displayed.
- 4 Screen- Quad mode. Automatically displays channels 1~4. If 4 Screen is selected again, the next chronological 4
channels (5~8) will be displayed.
- 9 Screen- Automatically displayes channels 1~9. If 9 Screen is selected again, the next cohoronological channels
(10~16+1~2) will be displayed.
- 16 Screen- Displays all 16 channels (available only in 16 channel models)
PTZ CONTROL- Open the DVR’s PTZ control. See section 3.4 PTZ for more information.
SEQUENCE- when selected, icon will appear on the bottom right corner of the screen, and the display screen will
be sequentially changed (Please note, option will be disabled if display area is in 16 channel mode).
ZOOM- Enables/ disables digital zoom function. When enabled, icon will appear and zoomed area will be
displayed on the bottom right corne. The Zoom will automatical y focus on the center of the camera’s display. To adjust ot, go
to the small zoom display at the bottom of the camera display and move the yellow frame to the desired are you would like to
view in zoom. To move the yellow frame, use your mouse to drag the lines of the yellow frame to the desired location. To go
back to live display mode, right-click on the screen and select “ZOOM” again. This feature is available in single channel mode
only.
INSTANT REC- Start/ Stop Panic Recording.
PLAYBACK- Select playback option:
- 10, 15, 30, 60 seconds- start playback from the selected number of seconds ago.
- 2, 3, 5, minutes- start playback from the selected number of minutes ago.
- Open Playback Mode-automatically go to instant playback.
SEARCH- Select video search options:
- Date/ Time- open calendar search.
- First/ Last Data- Go to the first or last recorded data.
- System/ Event Log- open log search window.
- Bookmarks- open bookmark search.
Backup - Users can archive a video clip recorded for a certain period on a selected channel.
SETUP- open the DVR’s main menu.
SHUT DOWN- Power off the DVR.
LOGOUT- User logout.