XENO XDR Series User manual

Installation and User Manual
for XDR Range of
Digital Video Recorders

INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before operation.
All
the
safety
and
operating
instructions
should
be
read
before
operation.
Environment Condition for Installation
1. To prevent electric shock or other hazard, do not expose this unit to rain, moisture or dust.
2. Place this unit in a well-ventilated place and do not place heat-generating objects on this
unit.
3. This unit should not be located in an area where it is likely to be subjected to mechanical
shocks.
Before You Start
1. Ensure the power switch is in the OFF position prior to installation.
2. Opening or removing the cover may expose you to dangerous voltage or other hazards.
3. Operate this unit within the range of room temperature and humidity.
4. Supply power through the type of power source indicated on the manufacturer’s label and
ith th l i l d d i thi it
w
ith
th
e power supp
l
y
i
nc
l
u
d
e
d
i
n
thi
s un
it
.
5. Keep this unit out of direct sunlight and heat.
6. Make sure conductive material does not go into the fan hole.
Notice
1. Before initial configuration or operation, first set TIME/DATE and then set this unit to the
FACTORY DEFAULT
setting
and
finally clear the HDD
Follow these steps in order
FACTORY
DEFAULT
setting
and
finally
clear
the
HDD
.
Follow
these
steps
in
order
.
Otherwise it may cause the HDD not to record or save setting value. Or it may record, but
you will not be able to search recorded data.
2. This unit is compatible with large sized HDD.
3. When setting RECORDING SETUP after installation, always set RECORD
CONFIGURATION and SCHEDULE SETUP. Setting Schedule setup is necessary as this
unit records according to Record type & Schedule setup. The default setting value for
Sc
h
edu
l
e
setup
i
s
Co
n
t
in
uous
m
ode
.
Sc edu e setup s Co t uous ode
4. Stop recording before powering off this unit by entering setup menu. Powering off while
recording may cause critical malfunctions such as Recording Error, Playback Error or System
Error.
CE Mark
A Declaration of Conformity in accordance with the following EU standards has been made.
f
The manu
f
acturer declares that the product supplied with this document is compliant the
provisions of the EMC Directive 89/336 EEC, the Low Voltage Directive LVD 73/23, the CE
Marking Directive 93/68 EEC and all associated amendments.
2

Table of Contents
CHAP. 1 Features and Package Contents -------------------------------------------------------- 5
1-1. Features -------------------------------------------------------- 5
1-2. Package Contents & Description -------------------------------------------------------- 6
CHAP. 2 Function of Buttons -------------------------------------------------------- 7
2-1. Front Panel -------------------------------------------------------- 7
2-2. Rear Panel -------------------------------------------------------- 9
2-3. Connector Pin -------------------------------------------------------- 10
CHAP. 3 Installation -------------------------------------------------------- 12
3
1
Cfi ti
12
3
-
1
.
C
on
fi
gura
ti
on --------------------------------------------------------
12
3-2. Detailed Configuration -------------------------------------------------------- 13
CHAP. 4 Display Configuration -------------------------------------------------------- 16
4-1. Current Status -------------------------------------------------------- 17
4
2
Di l St t
17
4
-
2
.
Di
sp
l
ay
St
a
t
us --------------------------------------------------------
17
4-3. Popup Menu -------------------------------------------------------- 18
4-4. Toolbar -------------------------------------------------------- 22
CHAP. 5 DVR Setup -------------------------------------------------------- 23
5
-
1
Operation
--------------------------------------------------------
23
5
-
1
.
Operation
--------------------------------------------------------
23
5-2. System -------------------------------------------------------- 26
5-3. Network -------------------------------------------------------- 34
5-4. Devices -------------------------------------------------------- 38
5-5. Record -------------------------------------------------------- 46
5
6
Event
52
5
-
6
.
Event
--------------------------------------------------------
52
CHAP. 6 Search -------------------------------------------------------- 57
6-1. Calendar Search -------------------------------------------------------- 57
6-2. Event Search -------------------------------------------------------- 59
6
-
3
Bookmark Search
--------------------------------------------------------
61
6
3
.
Bookmark
Search
61
3

CHAP 7
DVR Operation
62
CHAP
.
7
DVR
Operation
----------------------------------------------------------
62
7-1. Live Monitoring ---------------------------------------------------------- 62
7-2. Event Monitoring ---------------------------------------------------------- 66
7-3. Mouse Operation ---------------------------------------------------------- 67
7-4. Record ---------------------------------------------------------- 68
7-5. Audio ---------------------------------------------------------- 68
7-6. Search ---------------------------------------------------------- 68
7-7. Playback ---------------------------------------------------------- 71
7-8. Network Setup ---------------------------------------------------------- 73
CHAP. 8 Integrated Remote Station ---------------------------------------------------------- 84
8-1. IRS Setup ---------------------------------------------------------- 84
8-2. IRS Operation ---------------------------------------------------------- 86
8-3. Remote Viewer ---------------------------------------------------------- 89
8
4
Sh
90
8
-
4
.
S
earc
h
----------------------------------------------------------
90
8-5. Backup ---------------------------------------------------------- 93
8-6. Player ---------------------------------------------------------- 96
Appendix A Frequently Asked Questions ---------------------------------------------------------- 99
Appendix B Map of Screens ---------------------------------------------------------- 100
Appendix C Factory Default Settings ---------------------------------------------------------- 101
Appendix D HDD Calculation ---------------------------------------------------------- 108
Appendix E Specification ---------------------------------------------------------- 109
Appendix F
Remote Control
----------------------------------------------------------
111
Appendix
F
Remote
Control
----------------------------------------------------------
111
4

CHAPTER 1. Features and Package Contents
1-1. Features
Live Display
PIP (Picture in Picture), Freeze, Zoom, Sequence, PTZ function
1/4/6/8/9/13/16 Split display
Record
Picture image quality setup in 4 steps
Schedule recording / Holiday setup
Event recording by alarm and motion detection
Panic recording
Video Loss detection
BOOKMARK function
BOOKMARK
function
4ch Audio record
Pre-Event recording
Network
Monitoring, Setup, Search and Backup
DDNS support
E-mail notification
Playback
Easy search and playback by Date/Time, Event and Bookmark
Various playback speed (forward/Backward)
Backup
Data import/export via USB (Import /Export DVR settings)
Backup via USB or CD/DVD-RW
Network backu
p
p
Others
Simple and easy menu control with popup menu via mouse control
Multi-Language (English, French, Spanish, Italian, Portuguese, Dutch, Russian, Turkish and Polish)
Password lock
NTSC/PAL auto detection
Remote control
SPOT monitor
5

1-2. Package contents
1. Digital Video Recorder 2. Remote Control
IR
ALARM BOOKMARK
3. Power Cable 4. Power Adapter 5. User’s Manual 6. Software CD
7. Rubber Pad 8. HDD Absorber 9. Batteries 10. Rack Mount Bracket,
HDD Bolts
11. Mouse
6

CHAPTER 2. FUNCTION BUTTONS
2-1. Front Panel
12345
6 7 8
NO Name Function
1 LED Indicatin
g
o
p
eration status
<Note>
This manual covers the 4 channel, 8 channel and 16 channel digital video recorders. For simplicity,
the illustrations and descriptions in this manual refer to the 16 channel model.
gp
2 ALARM Panic recording (Press ALARM and channel button together. The selected
channel will begin record in Panic recording mode)
3 Function Key MSC Switch screen division from full screen to 16 split screen
(in 1, 4, 6, 8, 9, 13, 16 sequence )
PIP Picture In Picture mode
SEQ Auto camera image sequence in full screen mode
PRESET Press PRESET and channel button(1~16) together for Preset of PTZ
control
PTZ Switch LIVE mode to PTZ control mode
SEARCH Search recorded data on HDD
K i th SEARCH b tt f f d t b i
K
eep press
i
ng
th
e
SEARCH
b
u
tt
on
f
or a
f
ew secon
d
s
t
o
b
eg
i
n
playback directly
MENU Enter SYSTEM MENU
AUDIO Press AUDIO and channel button(1~4) together for Audio channel On.
Press AUDIO button alone to turn audio off.
MONITOR Switch screen between Spot and Monitor
STOP Stop for panic recording & playback, return to schedule recording,
cancel selected function key
4 BOOKMARK Bookmark
7

No Name Function
5 Direction Key Navigate in the menu (while playback)
OK/PAUSE/
FRZ
MENU(OK), LIVE(FREEZE), PLAY(PAUSE)
LEFT Backward playback (In FRZ mode: Step Backward)
RIGHT Forward Playback (In FRZ mode: step Forward)
UP Increase playback speed
(Press AUDIO and UP button together for audio volume up)
DOWN Decrease playback speed
(Press AUDIO and Down button together for audio volume
down)
down)
6 USB Port For recorded data backup and firmware upgrade
7 Camera Selection
/ PTZ Control
1~16 Button : Select camera channel in full screen mode
AUDIO + 1~4 Button : Select audio channel
1, + ZOOM IN
2
,
- ZOOM OUT
,
8 CD/DVD-RW For recorded data backup and firmware upgrade
8

1
2
3
4
7
11
10
2-2. Rear Panel
1
2
3
4
5
11
10
689
<Note>
No Name Function
1 RS485 Connection with PTZ Camera or other external devices using RS485
<Note>
You cannot mix NTSC and PAL equipment. For example you cannot use a PAL camera and a NTSC
monitor.
RELAY Output Relay Output terminal
SENSOR Input Sensor Input terminal
2 VGA VGA Output to CRT or TFT LCD Monitors
3 ETHERNET Connection to Ethernet devices
4 RS232C Connection to external devices such as PC using RS232C to control DVR
5 CAMERA Connection with NTSC/PAL Cameras
6 LOOP Camera Loop out
7 MONITOR Connection with NTSC/PAL Composite Monitor
8 SPOT Connection for Spot monitor
9 DC Power DC 12V 6.67A Adaptor
10 PS2 Mouse Connection to PS2 Mouse
11 Audio I/O Audio input/output & Microphone input
9

2-3. Connector Pin
[1] RS232
No Details No Details
1 N/C (Normal Close) 6 N/C (Normal Close)
2 RxD (Data Transmission) 7 N/C (Normal Close)
Connection with PC to view and control DVR.
3 TxD (Data Transmission) 8 N/C (Normal Close)
4 N/C (Normal Close) 9 N/C (Normal Close)
5 GND (Ground)
[2] VGA
VGA monitor output port to view screen via PC.
No Details No Details
1 Red Sig.(75Ω, 0.7 p-p) 9 N/C (Normal Close)
2 Green Sig.(75Ω, 0.7 p-p) 10 GND (Ground)
3 Blue Sig.(75Ω, 0.7 p-p) 11 GND (Ground)
4 N/C (Normal Close) 12 N/C (Normal Close)
5 GND
(
Ground
)
13 HYNC
(
Horizontal S
y
nc.
)
()
(y)
6 GND (Ground) 14 VSYNC (Vertical Sync.)
7 GND (Ground) 15 N/C (Normal Close)
8 GND (Ground)
No Details No Details
1 TX+ (Data Transmission) 5 N/C (Normal Close)
2
TX
(Data Transmission)
6
R/X
(Data Transmission)
[3] LAN
2
TX
-
(Data
Transmission)
6
R/X
-
(Data
Transmission)
3 RX+ (Data Transmission) 7 N/C (Normal Close)
4 N/C (Normal Close) 8 N/C (Normal Close)
10

[4] CAMERA input & LOOP output
[5] AUDIO
Camera Input
Loop Output
AIN1 ~ AIN 4: Audio Input CH1 ~ CH4
MIC: Microphone Input
AOUT: Audio Output
[6] RELAY OUT
Connection with PTZ camera, sensor, relay output.
No Details No Details No Details
1
RS485 D
10
ALARM D14
19
ALARM D7
3712 17 22126
1
RS485
D
-
10
ALARM
D14
19
ALARM
D7
2 RS485 D+ 11 ALARM D13 20 ALARM D6
3 GND 12 GND 21 ALARM D5
4 RELAY COM 13 ALARM D12 22 GND
5 RELAY NC 14
A
LARM D11 23
A
LARM D4
6 RELAY NO 15 ALARM D10 24 ALARM D3
7 GND 16 ALARM D9 25 ALARM D2
8 ALARM D16 17 GND 26 ALARM D1
9 ALARM D15 18 ALARM D8
11

3
1 C fi ti
CHAPTER 3. INSTALLATION
3
-
1
.
C
on
fi
gura
ti
on
[Typical DVR Installation]
12

3-2. Detailed Configuration
1) Rack mount
1
1. Remove all 4 bolts on side caps.
IR
ALARM BOOKMARK
2
3
2) HDD (Hard Disk Drive) connection
2. Attach Rack mount bracket to DVR.
3. Attach DVR with rack mount bracket to 19” Rack.
1. Connect Main Board and HDD1 using SATA cable and HDD power cable.
2. When you use just one HDD, install the HDD onto HDD1 location.
3. When you use two HDDs, install the first HDD onto HDD1 location and then install the second
HDD onto HDD2 location in order.
4. Stick the HDD absorber (included in the package) on the bottom of case and then install the HDD
on top of them by using the bolts (included in the package).
HDD Cable Connection HDD Fix
5. Screws must be inserted from outside of the case bottom.
MAIN BOARD
CD-RW
(MASTER)
MAIN
BOARD
HDD1
(MASTER
1) HDD2
(MASTER
2)
HDD1 HDD2 MAIN BOARD
xx
xx
xx
xx
xx
xx
13

[3] Camera
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear view of CAMERA
Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.
[4] Monitor
VIDEO A VIDEO CVIDEO B
IN OUT IN OUTIN OUT
Connect the video output marked MONITOR to VIDEO-IN of Main Monitor.
[5] Power Cable
Connect DC 12V, 6.67A Adaptor.
Before turning on, be sure all necessary devices such as Power adaptor,
cameras and Monitor are connected
p
ro
p
erl
y
to the DVR!
This unit is for DC 12V. Inade
q
uate su
pp
l
y
of
p
ower ma
y
cause breakdown.
<Note>
pp y
14
qppyp y
Be sure to power off DVR when connecting external devices.

[6] SPOT
SPEAKER
PC
MIC
Connect with the spot monitor as needed.
[7] OTHERS
VGA
MONITOR
PC
PC
SENSOR
SIREN
PTZ
CAMERA
PAN /TILT
CAMERA
RS232C : Control DVR through RS232C port by using PC.
RS485 : Control external device such as PTZ Cameras.
(Pin No.1 ~ 2 at Terminal Block).
RELAY Output : (Pin No.4 ~6 at Terminal Block).
SENSOR Input : (Pin No.8 ~ 11 / No.13 ~ 16 / No.18 ~ 21 / No.23 ~ 26
at Terminal Block).
GND : Ground (Pin No.3 / No.7 / No.12 / No.17 / No.22
at Terminal Block).
ETHERNET
:
Connection to LAN WAN and
Internet
ETHERNET
:
Connection
to
LAN
,
WAN
and
Internet
.
VGA : Connection to VGA Monitor (CRT, TFT LCD Monitor)
Resolution is set to 800x600 60 Hz
User can change resolution in DEVICES/ DISPLAY SETUP /
VGA SETUP / VGA RESOLUTION.
Audio Input : Microphone Input (A IN1 ~ A IN4)
Audio Output : Speaker Output (1ch OUT)
Microphone
Input :
Microphone Input
(MIC)
Microphone
Input
:
Microphone
Input
(MIC)
15

CHAPTER 4. Display Configuration
3
2
1
4
1Current Status Date/Time, HDD, Playback
2
Displa Stat s
Di l t t i
2
Displa
y
Stat
u
s
Di
sp
l
ay s
t
a
t
us
i
cons
3Popup Menu Monitoring popup menu in live mode
Playback popup menu in playback mode
PTZ control popup menu in PTZ mode
4Toolbar Playback toolbar, PTZ toolbar
16

[
1
]
Date/Time
4-1. Current Status
[]
[2] HDD
Live mode : Shows current date & time
Playback mode : Shows recorded date & time of the playback image
Live mode : HDD recorded space is marked red on the percentage bar.
[3] Playback Mode
A
vailable remaining days/time at current record mode is shown.
Playback mode : Shows percentage of playback.
In Playback mode, F stands for Forward playback, B for Backward playback.
The numbers show playback speed.
Eg.) F 16x, B 2x
4-2. Display Status
[Continuous Recording]
[Stop Recording]
[Alarm Recording]
[Motion Recording]
[Motion detected]
[Panic Recording]
[Alarm-In detected]
17

4-3. Popup Menu
By clicking right button of mouse, Monitoring popup menu appears in live mode, Playback popup
menu a
pp
ears in
p
la
y
back mode
,
PTZ control
p
o
p
u
p
menu a
pp
ears in PTZ mode.
While in LIVE display, click right button of mouse and MONITORING popup appears.
In full screen mode: All sub-menus are activated.
In split screen mode: PTZ, Zoom, PIP menus are not activated.
In 16 s
p
lit screen mode: Previous Pa
g
e
,
Next Pa
g
e
,
PTZ Control
,
Zoom
,
PIP are not activated.
pp p y , p p p pp
1) MONITORING POPUP MENU
1) Channel selection ( go to Channel ) sub-menu : CAM01 ~ CAM16
pg,g,,,
go to CHANNEL
SPLITTER
PTZ CONTROL
FREEZE
ZOOM
SEQUENCE
CAM01
CAM02
CAM03
CAM04
CAM05
CAM06
CAM07
C
AM
08
MONITORING
PIP
AUDIO
PANIC
PLAYBACK
SEARCH
SETUP MENU
C08
CAM09
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16
CAM10
2) 2x2, 3x3, 4x4 Split
Displays in 4, 9, 16 Screen Division. go to CHANNEL
SPLITTER
MONITORING
go to CHANNEL
SPLITTER
MONITORING
For 4ch/8ch DVR, 3X3 and 4X4 split sub-menus
will not be activated.
PTZ CONTROL
FREEZE
ZOOM
SEPUENCE
PIP
AUDIO
PANIC
PTZ CONTROL
FREEZE
ZOOM
SEQUENCE
PIP
AUDIO
PANIC
PLAYBAC
K
SEARCH
SETUP MENU
PLAYBAC
K
SEARCH
SETUP MENU
18

3) Previous Page
In full screen mode, clicking Previous Page menu will switch screen to lower number channel.
After channel 1, it rotates to channel 16.
4) N t P
In split screen mode, clicking Previous Page menu will switch screen to lower number
channel groups.
e.g.) [ch1/2/3/4] →[ch13/14/15/16] →[ch9/10/11/12] →[ch5/6/7/8]
In 16 split display mode, this function is not available.
4)
N
ex
t
P
age
In full screen mode, clicking Next Page menu will switch screen to higher number channel.
After channel 16, it rotates to channel 1.
In split screen mode, clicking Next Page menu will switch screen to higher number channel
groups.
e g ) [ch1/2/3/4]
→
[ch5/6/7/8]
→
[ch9/10/11/12]
→
[ch13/14/15/16]
5) PTZ Control
PTZ Panel appears when PTZ Control menu is clicked.
Click buttons with mouse control, or press SEQUENCE button to shift keys.
e
.
g
.
)
[ch1/2/3/4]
→
[ch5/6/7/8]
→
[ch9/10/11/12]
→
[ch13/14/15/16]
In 16 split display mode, this function is not available.
[PTZ Control Toolbar]
See Chapter 7 7-1 Live Monitoring 5] PTZ mode for more details.
6) Freeze : On / Off
[Virtual Joystick]
[PTZ
Control
Toolbar]
go to CHANNEL
SPLITTER
MONITORING
In Full screen mode, FRZ icon appears and screen freezes.
In split screen mode, FRZ icon appears and all channels freeze.
To exit freeze mode, click any sub-menus from MONITORING
except Audio and Panic.
On
Off
SPLITTER
PTZ CONTROL
FREEZE
ZOOM
SEQUENCE
PIP
AUDIO
PANIC
PLAYBACK
SEARCH
SETUP MENU
19

11) Search
Only the Admin and Manager have authority to access this Menu.
It is to search recorded data easily and playback.
Search by Time/Date, Event list and Bookmark is available.
12) Setup Menu
Only the Admin and Manager have authority to access and change all settings on all Sub-Menus.
[2] PTZ CONTROL Popup
While in PTZ mode, click right button of mouse and PTZ popup appears.
1) Preset Tour : Pan/Tilt on preset directions.
2) Learn Tour : Repeat learned Pan/Tilt directions.
3
)
A
uto Pan : Pan left/ri
g
ht automaticall
y
.
<Note>
)
gy
4) Power : On/Off
5) Light : Light on at night.
6) Wiper : Wipe moisture or water drops.
7) Pump : Pump water to remove dust.
8) Device Menu : Show OSD Menu of PTZ camera.
9) Exit PTZ Control : Exit and go back to Live view mode.
[3] PLAYBACK Popup
<Note>
Menus from 1) to 7) may not be available according to PTZ camera models.
1) Bookmark : Clicking BOOKMARK button while in playback mode,
time/date will be remembered for Bookmark Search.
2) D
it l ClikDE
INTERLACE b tt hil i l b k d
While in Playback mode, click right button of mouse and Playback popup appears.
go to CHANNEL
SPLITTER
PLAYBACK
2)
D
e-
i
n
t
er
l
ace :
Cli
c
k
DE
-
INTERLACE
b
u
tt
on w
hil
e
i
n p
l
ay
b
ac
k
mo
d
e.
De-interlace is available via Interpolation.
3) Search : Clicking SEARCH button while in playback mode will stop
playback mode and go to search mode.
Other Menus are the same as the Menus in LIVE POPUP.
SPLITTER
AUDIO
BOOKMARK
DE-INTERLACE
SEARCH
EXIT PLAYBACK
20