Xerox ColorStix 8200 Ink Sticks Series s User manual

User Guide 77
Specifications
Specifications
Material Safety Data Sheet for ColorStix® 8200 Ink
Sticks
SECTION 1- PRODUCT IDENTIFICATION
Trade NamesXerox Part No.
ColorStix®8200 Ink Sticks, Black016-2044-00, 016-2040-00
ColorStix®8200 Ink Sticks, Cyan016-2045-00, 016-2041-00
ColorStix®8200 Ink Sticks, Magenta 016-2046-00, 016-2042-00
ColorStix®8200 Ink Sticks, Yellow016-2047-00, 016-2043-00
Supplies Start-up Kit8200 SS 00, 8200 SS 01
Product Use: XEROX Phaser®8200 color printers
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Phaser®ColorStix®8200 Inks are a proprietary blend of polyethylene
and fatty amide waxes, resins, and dyes. The specific identity of ingredients is
withheld as a trade secret.
ColorStix®8200 solid inks are considered articles under Hazard
Communication regulations. This Material Safety Data Sheet is provided as a
customer service.
SECTION 3 - HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE: Skin
POTENTIAL HEALTH EFFECTS
Immediate Effects: None are known, when used as intended in Phaser®8200
Color Printers. See Section 11 for toxicology test information.
Chronic Effects: None are known
SIGNS AND SYMPTOMS OF EXPOSURE: None are known.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None are known.
SECTION 4 - FIRST AID MEASURES
EYES: Contact unlikely. If particles get into eyes, flush thoroughly with water.
INGESTION: Not applicable
INHALATION: Not applicable
SKIN: Wash skin thoroughly with soap and water
SECTION 5 - FIRE FIGHTING MEASURES
FLASH POINT: > 221 degrees C (>429 degrees F), Pensky-Martens closed
tester
FIRE & EXPLOSION HAZARDS: These inks will burn. During a fire, irritating
and toxic gases may be generated by thermal decomposition or combustion.
EXTINGUISHING MEDIA: All extinguishing agents classified as B and C are
effective, including dry powder(s), carbon dioxide, and halon.
FIRE FIGHTING INSTRUCTIONS: Avoid inhalation of smoke. As in any fire,

78 Phaser® 8200 Color Printer
Specifications
wear self-contained breathing apparatus, pressure demand, MSHA/NIOSH
approved, and full protective gear.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
SPILL OR LEAK: Not applicable
SECTION 7 - HANDLING AND STORAGE
HANDLING: No special precautions, when used as intended.
STORAGE: Avoid high temperatures. Keep ink below 60 degrees C
(140 degrees F)
SECTION 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
EXPOSURE GUIDELINES: None established.
ENGINEERING CONTROLS/PERSONAL PROTECTION: No special personal
protection indicated, when used as intended.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/ODOR: Waxy solid. Black, blue, red, or yellow in color/Faint
odor
SOLUBILITY IN WATER: Insoluble
MELTING POINT: Approximately 100 degrees C (212 degrees F)
SPECIFIC GRAVITY (Water = 1): Approximately 1, @ 25 degrees C
(77 degrees F)
SECTION 10 - STABILITY AND REACTIVITY
STABILITY: Stable.
CONDITIONS TO AVOID: Temperatures above 200 degrees C (392 degrees F)
INCOMPATIBILITY WITH OTHER MATERIALS: None
HAZARDOUS POLYMERIZATION: Will not occur
HAZARDOUS DECOMPOSITION PRODUCTS: Material may decompose into
toxic byproducts when heated to temperatures above 200 degrees C
(392 degrees F).
SECTION 11 - TOXICOLOGICAL INFORMATION
TOXICITY: Oral LD50 >5 g/kg (rats); practically non-toxic
SKIN IRRITATION: Primary Dermal Irritation Index = 0.0; not skin irritants.
CARCINOGENICITY: Components not listed by IARC, NTP, or OSHA.
SECTION 12 - ECOLOGICAL INFORMATION
No known impact

User Guide 79
Specifications
SECTION 13 - DISPOSAL CONSIDERATIONS
This product is not a hazardous waste as specified in 40CFR261. TCLP below
hazardous waste levels set by EPA. State and local waste disposal
requirements, however, may be more restrictive. Manage and dispose of waste
in accordance with all federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT: Not regulated.
SECTION 15 - REGULATORY INFORMATION
TSCA: This material has been manufactured in compliance with the EPA
Toxic Substances Control Act (TSCA).
RCRA (Resource Conservation and Recovery Act): Not a hazardous waste as
specified in 40CFR261. TCLP below hazardous waste levels set by EPA.
SECTION 16 - OTHER INFORMATION
Original preparation date: 11/27/01
Xerox Corporation
Office Printing Business
Environmental, Health & Safety
P.O. Box 1000
Mail Stop 60-512
Wilsonville, Oregon 97070
Safety Information: 800-828-6571
Health Information: 716-422-2177
Material Safety Data Sheet for Silicone Intermediate
Transfer Layer Fluid
SECTION 1- PRODUCT IDENTIFICATION
Trade Name: Xerox Silicone Intermediate Transfer Layer Fluid, impregnated
into printer's maintenance roller.
Xerox part number 016-1933-00 (replacement standard capacity maintenance
kit)
Xerox part number 016-1932-00 (replacement extended capacity maintenance
kit)
Product Use: Xerox Phaser® 8200 color printers
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Silicone Intermediate Transfer Layer Fluid is a proprietary blend of
silicone oils. Specific identities of components, and their percentage
composition, are withheld as a trade secret.

80 Phaser® 8200 Color Printer
Specifications
SECTION 3 - HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE: Skin, eyes
POTENTIAL HEALTH EFFECTS: Health effects from this product are expected
to be negligible, when product is used as intended in Xerox Phaser®8200
Color Printers.
Immediate Effects:
Inhalation: Not an expected route of entry
Skin: May cause mild irritation.
Eyes: May cause mild irritation.
Ingestion: Not an expected route of exposure.
Chronic Effects: None known or expected.
SIGNS AND SYMPTOMS OF EXPOSURE
Mild skin or eye irritation.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
None known
SECTION 4 - FIRST AID MEASURES
INHALATION: Not a route of exposure for this product.
EYES: Flush thoroughly with water. Seek medical attention if symptoms
occur.
SKIN: Wash thoroughly with soap and water. Seek medical attention if
symptoms of irritation occur.
INGESTION: Not a route of exposure for this product.
SECTION 5 - FIRE FIGHTING MEASURES
FLASH POINT: Flash point of fluid is 226 degrees C, Pensky-Martens
closed-cup tester.
EXTINGUISHING MEDIA: All extinguishing agents classified as B and C are
effective, including dry powder(s), CO2, and halon.
FIRE FIGHTING INSTRUCTIONS: As for any fire, wear self-contained
breathing apparatus, pressure demand, MSHA/NIOSH approved, and
protective gear.
FIRE AND EXPLOSION HAZARDS. During a fire, irritating and toxic
substances may be generated by thermal decomposition or combustion. No
unusual fire hazards expected.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
SPILL OR LEAK: Fluid is impregnated into maintenance roller. Small
amounts (ie., drops) may result from normal handling. Absorb and place in an
appropriate disposal container. Clean spills thoroughly because residue can
be slippery.
SECTION 7 - HANDLING AND STORAGE
HANDLING: Wash hands with soap and water after contact. Clean spills per
SECTION 6.
STORAGE: No special requirements.

User Guide 81
Specifications
SECTION 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
No special protection indicated when used as intended.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Clear liquid impregnated into maintenance roller.
ODOR: Mild
SOLUBILITY IN WATER: No data
SPECIFIC GRAVITY: Specific gravity of fluid is 0.97 (water=1)
SECTION 10 - STABILITY AND REACTIVITY
STABILITY: Stable.
INCOMPATIBILITY WITH OTHER MATERIALS: Strong oxidizing agents
HAZARDOUS DECOMPOSITION PRODUCTS: At elevated temperatures,
formaldehyde may be generated.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11 - TOXICOLOGICAL INFORMATION
No toxicology data on mixture
SECTION 12 - ECOLOGICAL INFORMATION
Not available.
SECTION 13 - DISPOSAL CONSIDERATIONS
Fluid is not listed as RCRA hazardous waste. Dispose of in accordance with
federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT: Not regulated.
SECTION 15 - REGULATORY INFORMATION
The following information pertains to the ingredients of Xerox Silicone
Intermediate Transfer Layer Fluid:
TSCA (Toxic Substances Control Act): Listed in the TSCA inventory as
verified by our suppliers.
RCRA (Resource Conservation and Recovery Act): Not listed as RCRA
hazardous wastes.
The ingredients of this fluid are not listed as carcinogenic by OSHA, IARC or
NTP.

82 Phaser® 8200 Color Printer
Specifications
SECTION 16 - OTHER INFORMATION
Original preparation date:11/27/01
Xerox Corporation
Office Printing Business
Environmental, Health & Safety
P.O. Box 1000
Mail Stop 60-512
Wilsonville, Oregon 97070
Safety Information: 800-828-6571
Health Information: 716-422-2177
Material Safety Data Sheet for CleanTex®Alcopad
SECTION 1 – PRODUCT IDENTIFICATION
Trade NamesXerox Part No.
Alcopad016-1845-00
Product identification numbers: 806B, 806C, 806H, 806T, 806Z, 806
Chemical name and synonyms: Isopropyl Alcohol
Chemical formula: CH2CH(OH)CH3
Emergency telephone numbers: CHEMTREC (Transportation): 1-800-424-9300
Product Use: Xerox Phaser® 8200 Color Printer
SECTION 2 – INFORMATION ON INGREDIENTS
Component CAS# % OSHA PEL (ppm) ACGIL TLV (ppm)
Isopropyl alcohol 67-63-0 91.0 400 400
Deionized water 7732-18-5 9.0 NA NA
SECTION 3 – HAZARDS IDENTIFICATION
Product is distributed as a single-use, presaturated pad, in which all the liquid
is absorbed by the applicator. Isopropyl alcohol is a flammable liquid. Eye
contact will cause local irritation and burning sensations with possible injury
if not removed promptly. Repeated or prolonged contact with skin may
produce irritation and cause dermatitis. Exposure above TLV may cause
irritation of respiratory tract and eyes along with headaches, dizziness and
CNS effects. May be harmful if swallowed.
Carcinogenicity (OSHA/NTP/IARC/ACGIH): Not Listed.
Medical Conditions Aggravated by Exposure: Not Listed.
SECTION 4 – FIRST AID MEASURES
EYE CONTACT: Flush with water for 15 minutes, including under eyelids.
Get Medical help.
SKIN CONTACT: Flush with water.
INHALATION: Remove to fresh air. Keep at rest. Restore and/or support
breathing as needed. Get prompt Medical attention.
INGESTION: In the unlikely event of ingestion of a wiper, first aid measures
should focus on removal of the object and preventing choking. Once removed,

User Guide 83
Specifications
keep affected person at rest. Call physician immediately.
SECTION 5 – FIRE-FIGHTING MEASURES
FLASH POINT (TCC): 56 degrees F
FLAMMABLE LIMITS (% BY VOLUME): LEL: NA UEL: NA
AUTOIGNITION TEMPERATURE degrees F (degrees C): NA
EXTINGUISHING MEDIA: Isopropyl-alcohol fires may be extinguished using
carbon dioxide, dry chemical or alcohol foam. Water may be used to cool
containers exposed to the fire.
UNUSUAL FIRE OR EXPLOSION HAZARDS: Isopropyl alcohol may release
vapors which may ignite at or above flash point.
NFPA RATING: HEALTH (1)
FLAMMABILITY (3)
REACTIVITY (0)
Formulation is classified as an OSHA Class IB Flammable Liquid
NA = Not Available
SECTION 6 – ACCIDENTAL RELEASE MEASURES
Since the isopropyl-alcohol solution is completely absorbed by the applicator
and the amount of isopropyl alcohol per applicator is small, the chance of a
significant spill occurring is small. In the event however, that a significant
amount of liquid is released, ventilate the area, especially low areas where
vapors may collect, and remove all sources of ignition. Cleanup personnel
need protection against liquid contact and vapor inhalation.
SECTION 7 – HANDLING AND STORAGE
Store in a clean, cool, ventilated area away from sources of ignition and
oxidizing agents. Handle and store in a manner suitable for an OSHA class IB
Flammable Liquid. Electrical services must meet applicable codes. Use
non-sparking tools.
SECTION 8 – EXPOSURE CONTROL – PERSONAL PROTECTION
Provide ventilation to maintain TLV. Use non-sparking tools. Avoid
inhalation of vapors, contact with eyes and repeated or prolonged contact with
skin. Do not take internally.
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT (80 degrees C) (180 degrees F)
% VOLATILE BY VOLUME @ 25 degrees C: 100
VAPOR PRESSURE (mmHg @ 25 degrees C): 33
EVAPORATION RATE (BUTYL ACETATE-1) >1
VAPOR DENSITY (AIR = 1): <1
FORM: liquid
% SOLUBLE IN WATER @ 25 degrees C: 100
ODOR: alcohol
SPECIFIC GRAVITY (G/CC @ 25 degrees C): 0.79
APPEARANCE OF LIQUID: clear

84 Phaser® 8200 Color Printer
Specifications
SECTION 10 – STABILITY AND REACTIVITY
STABILITY: Stable
HAZARDOUS POLYMERIZATION: Will not occur.
INCOMPATIBILITIES / CONDITIONS TO AVOID: Caustics, amines,
alkanolamines, aldehydes, ammonia, strong oxidizing agents and chlorinated
compounds.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide
SECTION 11 – TOXICOLOGICAL INFORMATION
Not Available
SECTION 12 – ECOLOGICAL INFORMATION
Not Available.
SECTION 13 – DISPOSAL CONSIDERATIONS
Follow Federal, State and Local Regulations.
SECTION 14 – TRANSPORT INFORMATION
DOT CLASSIFICATION: Not Regulated.
Proper Shipping Name:
Hazard Class:
UN Number:
Packing Group:
Hazard Labeling:
IATA / ICAO CLASSIFICATION: Not Regulated.
Proper Shipping Name:
Hazard Class:
UN Number:
Packing Group:
Hazard Labeling:
IMDG CLASSIFICATION: Not Regulated.
Proper Shipping Name:
Hazard Class
IMDG Page #
Packing Group:
Flash Point (degrees C):
Marine Pollutant:
SECTION 15 – REGULATORY INFORMATION
SARA TITLE III REPORTING:
Toxic Chemical (Section 313): Not Listed.
Extremely Hazardous Substance: Not Listed.
Section 302, 304, 311, 312)
Hazard Class:
Chronic Health: Yes
Acute Health: Yes
Fire Hazard: Yes
Pressure Hazard: No

User Guide 85
Specifications
Reactivity Hazard: No
TSCA INVENTORY STATUS: All components listed are on the TSCA
inventory.
SECTION 16 – OTHER INFORMATION
The information provided herein is compiled from internal reports and data
from professional publications. It is furnished without warranty of any kind,
expressed or implied. It is intended solely to assist in evaluating suitability
and proper use of the material and in implementing safety precautions and
procedures. Employees should use this information as a supplement to other
information gathered by them and must make independent determination of
suitability and completeness of information from all sources to assure proper
use of these materials. All information used must be determined by the user to
be in accordance with applicable federal, state and local laws and regulations.
PREPARED BY:
CleanTex Products
33 Murray Hill Drive
Nanuet, NY 10954
June 1997