Xerox 4850 HighLight Color User manual

XEROX
Xerox 4850/4890 HighLight Color
Laser Printing Systems
Message Guide
Version 5.0
November 1994
720P93620

Xerox Corporation
701 S. Aviation Boulevard
El Segundo, CA 90245
© 1994 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of
copyrightable material and information now allowed by statutory
or judicial law or hereinafter granted, including without limitation,
material generated from the software programs which are
displayed on the screen, such as icons, screen displays, looks,
etc.
Printed in the United States of America
Publication number: 720P93620
Xerox® and all Xerox products mentioned in this publication are
trademarks of Xerox Corporation. Products and trademarks of
other companies are also acknowledged.
Changes are periodically made to this document. Changes,
technical inaccuracies, and typographic errors will be corrected in
subsequent editions.
This document was created on the Xerox 6085 Professional
Computer System using VP software. The typefaces used are
Optima, Terminal, and monospace.

Table of contents
Introduction v
Conventions v
1. COMPRESS (CP) command messages 1-1
2. Data Capture Utility (DCU) messages 2-1
System failure or reload messages 2-6
3. Disk Save and Restore (DSR) messages 3-1
4. File Conversion Utility (FCU) messages 4-1
5. General floppy utility (FLF) messages 5-1
FLF messages 5-15
6. Forms compilation (FD) messages 6-1
7. Host Interface Processor (HIP) messages 7-1
8. Interpress font utility (IFU) messages 8-1
9. Operating system software (OSS) messages 9-1
OS level 0: Confirmation messages 9-1
OS level 1: Informational messages 9-10
OS level 2: Routine maintenance messages 9-41
OS level 3: Printer problem messages 9-66
OS level 4: System or tape problem messages 9-71
OS level 6: Job integrity problem messages 9-75
OS level 7: System problem messages 9-96
OS level 8: Probable severe software errors 9-101
OS level 9: Probable severe hardware errors 9-107
10. Job source library compilation (PDL) messages 10-1
11. PURGE (PG) command messages 11-1
12. Printer subsystem controller (PSC) command messages 12-1
13. Queue management (QM) messages 13-1
14. SCALE command messages 14-1
15. Status file creation utility (SFC) command messages 15-1
16. Status file services (SFS) command messages 16-1
17. System verification error messages 17-1
XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE iii

TABLE OF CONTENTS
18. Interpress (IP) error messages 18-1
Appearance error messages 18-2
Appearance warning messages 18-4
Appearance warning: 18-5
Appearance warning (page n): 18-5
Fatal error messages 18-7
Fatal Error: 18-7
Fatal Error (page n): 18-8
Informational messages 18-11
Master error messages 18-14
Master warning messages 18-21
Page error messages 18-21
System problem messages 18-22
System Problem: 18-22
System Problem (page n): 18-23
19. Finishing configuration (FCG) messages 19-1
20. HARDCOPY graphics printing (PR) command messages 20-1
21. HSPP or SDI messages 21-1
Appendix A-1
A. Abbreviations A-1
iv XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE

Introduction
The Xerox 4850/4890 HighLight Color Laser Printing System
Message Guide provides a description of all messages that may
appear on your system controller display or printed summary
sheet, and the appropriate action or actions to take, if any are
required.
This guide is intended for users who have some experience using
a Xerox laser printing system (LPS).
Conventions
This guide uses the following conventions:
<> Angle brackets are used for names of keys.
Bold Bold is used for text you enter.
italics Italics is used for variable information and names of books.
UPPERCASE Uppercase letters are used for command names.
<ENTER> Use the <ENTER> key to execute commands.
function key Press the function key to invoke the specified action. Do not
also press <ENTER>.
XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE v

1. COMPRESS (CP)
command messages
COMPRESS (CP) command messages may appear during the
process of compressing the system disk.
This chapter lists and describes each CP message and provides
the appropriate actions to take as required. Refer to your Xerox
4850/4890 HighLight Color LPS Command Reference for
additional information.
CP1010 COMPRESS now restoring the print file
You entered the COMPRESS command. The process has moved
the print file to a different area of the system disk.
Action None.
CP1020 NOW PROCESSING DP0:
CP1030 NOW PROCESSING DP1:
CP1040 NOW PROCESSING DP2:
CP1050 NOW PROCESSING DP3:
You entered the COMPRESS command. The system is currently
compressing the indicated disk pack unit.
Action None.
CP1800 COMPRESS processor aborting.
You entered the ABORT command during the compress process.
The system disk is partially compressed.
Action None.
CP1900 Insufficient working memory for COMPRESS.
Not enough dynamic memory exists for the compress process.
Action Contact your service representative to obtain additional memory
capacity.
CP2700 Invalid keyin.
You entered the COMPRESS command incorrectly.
Action Reenter the command correctly.
XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE 1-1

COMPRESS (CP) COMMAND MESSAGES
CP2710 Keyins are not allowed at this time.
The compress process started, and the system cannot process
any other commands at this time.
Action 1. Wait for the compress process to complete.
2. Reenter the command.
CP2720 Invalid start command.
You entered the COMPRESS command incorrectly.
Action Reenter the command correctly.
CP9100 File integrity error. Edit and print CPR000.TMP
The system detected a sector that was allocated multiple times
and terminated the compress function. The system lists the
sector in a special file (CPR000.TMP).
Action 1. Print the CPR000.TMP error log to locate the problem.
2. Call your service representative and be prepared to provide
the information contained in the log.
1-2 XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE

2. Data Capture Utility
(DCU) messages
Data Capture Utility (DCU) records console activity such as
message displays and operator keyins, and allows a redisplay or
printout of this data. You can use the DCU to track and monitor
system activity, and as a training tool. It is also helpful in
analyzing system problems.
DCU messages may appear when entering DCU commands,
capturing data, or playing back console activity. This chapter lists
and describes each DCU message and provides appropriate
actions to take as required. Refer to the Xerox 4850/4890
HighLight Color LPS Command Reference for additional
information on DCU commands.
DC0100 Reminder set to nminutes for device(s): CONSOLE
You entered the DCU CAPTURE command with the REMINDER
option or you entered the DCU REMINDER command. Your
requested reminder message is in effect for n minutes. The
default value for the reminder period is 60 minutes.
Action None.
DC0130 DCU capturing CONSOLE for ndays
You entered the DCU CAPTURE command. All console data is
currently being captured and retained on the system for ndays.
Action None.
DC0140 Reminder OFF for device(s): CONSOLE
You entered DCU REMINDER OFF or DCU REMINDER 0. All
reminders are now off for the console device.
Action None.
DC1020 DCU disconnecting all devices, and initializing all files
You entered the DCU RESET command and responded with Yes
to the confirmation prompt. All devices are being disconnected
and all captured data is being deleted. Data Capture is now off.
Action None.
XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE 2-1

DATA CAPTURE UTILITY (DCU) MESSAGES
DC1030 DCU exiting.
You entered the DCU EXIT command and responded with Yes to
the confirmation prompt. DCU has now stopped capturing data.
Action None.
DC1040 DCU formatting to console: CONSOLE
You entered the DCU FORMAT CONSOLE DISPLAY command.
This message indicates formatting is taking place and is being
output to the console.
Action None.
DC1041 DCU formatting to printer: CONSOLE
You entered DCU FORMAT CONSOLE PRINT. Formatting is
taking place and is being output to the printer.
Action None.
DC1045 DCU formatting stopped. No captured data to format.
You entered the DCU FORMAT command. The requested
captured data was not present in the DCU database because it
was deleted or because the DCU was inactive for the specified
time.
Action Enter DCU CAP to restart DCU capturing if DCU was turned off.
DC1060 Data capturing is currently inactive
You entered the DCU SHOW STATUS command when DCU was
turned off.
Action Enter DCU CAP to restart DCU capturing.
DC1080 DCU disconnecting from device: CONSOLE
This informative message displays in response to a DCU
CAPTURE OFF command.
Action None.
DC1090 Invalid DCU command: Retention period >40 days
You entered the DCU CAPTURE command with a retention
period greater than 40 days. The command was rejected.
Action Reenter the command using a retention period of 40 days or
less.
2-2 XEROX 4850/4890 HIGHLIGHT COLOR LPS MESSAGE GUIDE