Xerox WORKCENTER 5222 User manual

Xerox Multifunction Devices
Customer Tips
PDL Reference Guide for the
WorkCentre 5222/5225/5230
dc08cc0440
October 23, 2008
…for the use
r
Accessing Extended Features
Overview
This document enables you to access the extended features of the WorkCentre
5222/5225/5230 in environments that do not have a custom print driver.
This document applies
to the stated Xerox
products Note: The commands and syntax used in this document requires familiarity with either
PostScript (PS) or Printer Command Language (PCL).
. It is assumed
that your device is
equipped with the
appropriate option(s)
to support the
information within this
document.
This document provides the Printer Description Language (PDL) commands and syntax
for each feature. The following items are also included:
•A PCL table that describes the PCL features the WorkCentre supports and the syntax
to use the feature.
•A PS table that describes the PS features the WorkCentre supports and the syntax to
use the feature.
This document is not intended to be a complete PS or PCL reference manual. It is a
guide for using the PS and PCL commands with the WorkCentre 5222/5225/5230. Refer
to these sources for additional PS and PCL information:
•PostScript Language Reference Manual, Third Edition, ISBN 0-201-38922-8,
•PCL5 Printer Language Technical Reference Manual
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13210/bpl13210.pdf),
•Printer Job Language Technical Reference Manual
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13208/bpl13208.pdf), a
Hewlett-Packard manual.
dc08cc0440
Customer Support Page 1

Using this Guide
Search the Feature Table to determine whether the feature you wish to use is supported.
Verify that the feature is supported by the platform. For example, the WorkCentre must have an optional
finisher installed to use stapling commands.
Follow across the table to find the syntax listed for the PDL examples shown. Reference the
“Dependencies/Caveats” section when working with PS and/or PCL commands.
PCL
This WorkCentre supports PCL5e and PCL XL emulations that enable the features listed in the following
table.
Feature Description
Job Name The value for Job Name is stored for printing on the banner page.
Custom Paper Size Customer designated paper size on which to print a job.
Media Size The size of media on which to print a job.
Media Source Specifies the tray to supply the job’s media.
Output Location Indicates the output bin where the completed print job is sent.
Stapling Indicates use and location of staple(s).
Punch Indicates use, location, and number of holes to be punched.
Booklet This command enables you to print documents as booklets. The pages are
reordered sequentially and are oriented so when folded, the paging is
correct.
Quantity Use this command to specify the number of collated sets of a document.
Resolution Resolution used to image a job.
Bits Per Pixel This command sets the color depth value.
Copies Use this command to specify the number of uncollated sets of a document
in a print job.
Simplex Delivers one-sided output.
Duplex Delivers two-sided output.
Orientation Delivers output in landscape or portrait orientation.
Force Short Edge
Feeding Rotates orientation of job.
Job Mode Specifies the Job Mode.
Job Type Specifies Confidential Print or Proof Print.
Interleaving Paper
(transparency
separator)
Insert blank media to separate sheets of transparent media.
Job Based
Accounting Allows entry of an accounting code and user ID. To enable this feature the optional Network Accounting kit is required.
Auditron
Delayed Print Specify the time to print a job.
Banner Sheet Turns on/off the banner sheet that prints at the beginning of every job.
dc08cc0440
Customer Support Page 2

PCL/PJL Implementation
The following table contains the PCL feature commands and shows the syntax required to use the feature.
After the table are examples of how to use these commands and examples of a PCL file.
Feature Implementation Values
Job Name @PJL SET JOBNAME =
"jobname-string" Where jobname-string is a maximum of 32 characters
Custom
Paper Size –
available only
for PCL
You have to specify by PCL:
<ESC>&l101A
Width of Custom Paper is specified by
<ESC>&f#I
where # equals decipoints (88.9 mm –
297.0 mm).
Length of Custom Paper is specified by
<ESC>&f#J
where # equals decipoints (98.4 mm –
432.0 mm).
For instance:
4.25-inch x 5.5-inch will give
<ESC>&f3060I3960J by
4.25-inch x 720 decipoints/inch = 3060
and
5.5-inch x 720 decipoints/inch = 3960.
dc08cc0440
Customer Support Page 3

Feature Implementation Values
Media Size @PJL SET PAPER = value Where value is one of the following:
A3: A3 (297 x 420mm)
A4: A4 (210 x 297mm)
A5: A5 (180 x 210mm)
JISB4: B4 (257 x 364mm)
JISB5: B5 (182 x 257mm)
STATEMENT: Statement (5.5 x 8.5”) †
EXECUTIVE: Executive (7.25 x 10.5”)
LETTER: Letter (8.5 x 11”)
JISEXEC: 8.5 x 13”
LEGAL: Legal (8.5 x 14”)
LEDGER: Tabloid (11 x 17”)
COM10: No. 10 Envelope (4.1 x 9.5”)
DL: DL Envelope (110 x 220mm)
MONARCH: Monarch Envelope (3.9 x 7.5”)
C5: C5 Envelope (162 x 229mm)
CUSTOM: Custom paper
†: Whether each paper is available depends
on NV memory setting.
The following paper sizes are only available with
bi-pass tray.
A6: A6 (105 x 148mm)
JISB6: B6 (128 x 182mm)
A4COVER: A4 Cover (223 x 297mm)
POSTCARD: Postcard (4 x 6")
50X70: 5 x 7”
8X10: 8 x 10”
SPANISH: 215 x 315mm
LETTERCOVER: 9 x 11”
11X15: 11 x 15”
JPOST: Postcard (100 x 148mm)
JPOSTD: Postcard (148 x 200mm)
TYOUKEI3: Envelope (120 x 235mm)
dc08cc0440
Customer Support Page 4

Feature Implementation Values
<ESC>&l int A Where int is one of the following:
27: A3 (297 x 420mm)
26: A4 (210 x 297mm)
25: A5 (180 x 210mm)
46: B4 (257 x 364mm)
45: B5 (182 x 257mm)
41: Statement (5.5 x 8.5”) †
1: Executive (7.25 x 10.5”)
2: Letter (8.5 x 11”)
18: 8.5 x 13”
3: Legal (8.5 x 14”)
6: Tabloid (11 x 17”)
81: No. 10 Envelope (4.1 x 9.5”)
90: DL Envelope (110 x 220mm)
80: Monarch Envelope (3.9 x 7.5”)
91: C5 Envelope (162 x 229mm)
101: Custom paper
†: Whether each paper is available depends
on NV memory setting.
The following paper sizes are only available with
bi-pass tray.
24: A6 (105 x 148mm)
44: B6 (128 x 182mm)
200: A4 Cover (223 x 297mm)
216: Postcard (4 x 6")
204: 5 x 7”
208: 8 x 10”
43: 215 x 315mm
201: 9 x 11”
217: 11 x 15”
71: Postcard (100 x 148mm)
72: Postcard (148 x 200mm)
218: Envelope (120 x 235mm)
Media
Source @PJL SET MEDIASOURCE = value Where value is one of the following:
TRAY1: Feed from paper tray1
TRAY2: Tray2
TRAY3: Tray3
TRAY4: Tray4
SMH: Tray5 (Bypass)
TRAY6: Tray6
dc08cc0440
Customer Support Page 5

Feature Implementation Values
<ESC>&l int H Where int is one of the following:
0: Feed paper from default tray
4: Tray1
1: Tray2
5: Tray3
8: Tray4
7or 20 = Auto
2or 3or 6= Tray5 (Bypass)
21: Tray6
Output
Location @PJL SET OUTBIN = value Where value is one of the following:
UPPER: Center output tray (w/o finisher)
MAINTRAY: Center output tray (w/o
finisher)
CENTERTRAY: Center output tray (w/o
finisher)
MAINTRAY2: Center output tray (w/ B-
Finisher)
LOWER: Side Tray (facing up) (w/ side tray)
SIDETRAY: Side Tray (facing up) (w/ side
tray)
OUTBIN101: Finisher tray (w/ finisher)
<ESC>&l int G Where int is one of the following:
0: Automatic Selection
1: Center output tray (w/o finisher)
2: Side Tray (facing up) (w/ side tray)
4: Center output tray (w finisher)
6: Finisher tray (w/ finisher)
Stapling @PJL SET STAPLE = value Where value is one of the following:
TOPDUAL
TOPLEFT
TOPRIGHT
BOTTOMDUAL
BOTTOMLEFT
BOTTOMRIGHT
LEFTDUAL
RIGHTDUAL
SADDLE
NONE
Punch @PJL SET PUNCH =
value1
@PJL SET JOBATTR =
”@PNHN = value2”
Where value1 is one of the following:
TOP
RIGHT
LEFT
BOTTOM
NONE
Where value2 is one of the following:
TWO: 2 holes
THREE: 3 holes
FOUR: 4 holes
dc08cc0440
Customer Support Page 6

Feature Implementation Values
Booklet @PJL SET JOBATTR =
“@BKLT = value1”
@PJL SET JOBATTR =
“@BKSG = value2”
@PJL SET JOBATTR =
“@BKDN = int1”
Where value1 is one of the following:
NONEDIVIDE: Compile a booklet as long
as the number of sheet does not exceed the
limit
MANUALDIVIDE: Divide sheets based on
the specified limit manually(The number of
sheets is specified with “@BKDN”).
OFF: Do not compile a booklet
Where value2 is one of the following:
RIGHT = Right / Bottom Bind
LEFT = Left / Top Bind
Where int1 is:
1~9999 = Booklet dividing number for each
set
Quantity @PJL SET QTY = int Where int is:
1-999
(If you use this parameter, it also indicate
use collate mode automatically.)
Resolution @PJL SET RESOLUTION =
value Where value is one of the following:
600
Bits Per Pixel @PJL SET BITSPERPIXEL
= value Where value is one of the following:
1: 1 bit per pixel (per plane)
Copies @PJL SET COPIES = int Where int is:
1-999
(This parameter used for uncollated mode.)
<ESC>&l int X Where int is:
1-999
Simplex @PJL SET DUPLEX =
value1 Where value1 is one of the following:
OFF: simplex
<ESC>&l int S Where int is one of the following:
0: simplex
Duplex @PJL SET DUPLEX =
value1
@PJL SET BINDING =
value2
Where value1 is one of the following:
ON: duplex
Where value2 is one of the following:
LONGEDGE
SHORTEDGE
(value2 is used combined with value1=ON)
<ESC>&l int S Where int is one of the following:
1: Duplex Long Edge Binding
2: Duplex Short Edge Binding
Orientation @PJL SET ORIENTATION
= value Where value is one of the following:
PORTRAIT
LANDSCAPE
dc08cc0440
Customer Support Page 7

Feature Implementation Values
<ESC>&l int O Where int is one of the following:
0: Portrait
1: Landscape
2: Reverse Portrait
3: Reverse Landscape
Force short
edge feeding @PJL SET PAPERDIRECTION = value Where value is one of the following:
SEF: Short Edge Feed
LEF: Long Edge Feed
Job Mode @PJL JOB MODE = value Where value is one of the following:
PRINTER for Printer
Job Type @PJL SET HOLD = value1
See Example 3,4
@PJL SET HOLDKEY
="four-digit string"
Where value1 is one of the following:
PROOF: proof print
STORE: confidential print (secure
print)
The HOLDKEY variable acts as a password
without encryption to protect a held job.
Four-digit string can be any four-digit value
from 0000 to 9999. The default value is "".
When "" (null) is specified, no password is
required.
Interleaving
Paper(Transp
arency
Separator)
@PJL SET SLIPSHEET =
value Where value is one of the following:OFF:
Job Based
Accounting
Or
Auditron
@PJL SET JOBATTR =
"@JOAU = string1"
@PJL SET JOBATTR =
"@JOAP = string2"
@PJL SET JOBATTR =
"@DAID = string3"
Where string1 is a maximum of 32 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as job owner (Capital character
& small character is distinguished)
Where string2 is a maximum of 12 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as password without encryption.
It can be null (zero length string)
Where string3 is a maximum of 32 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as account ID. It can be null
(zero length string)
Note: Auditron and JBA cannot be used at the
same time. So the same command works for
both modes.
Delay Print @PJL SET JOBATTR =
"@PRTM =
YYYY:MM:DD:hh:mm"
YYYY:MM:DD:hh:mm
YYYY: year(AD 2000～2099)
MM: month (1～12)
DD: day (1～31)
hh: hour(0～23)
mm: minute(0～59)
dc08cc0440
Customer Support Page 8

Feature Implementation Values
Banner Sheet @PJL SET JOBATTR=
"@BANR=value"
@PJL SET JOBATTR=
"@BCMT=comment string"
Where value is one of the following:
START: start sheet
DEVICE: depend on device setting
OFF: no banner sheet
Where string is a maximum of 255 characters
(ASCII characters in the range 20h - 7Eh are
allowed Only) as comment for banner.
PJL Template
This section illustrates a standard PJL template that is used to access general print features as
well as WorkCentre Product specific features. This template lists each feature and the syntax,
both PCL commands and PJL, required to use these features. The next section of this document
contains other examples of how to use these commands.
Section 1 (Opening Command, Required for all files)
<ESC>%-12345X@PJL JOB MODE=PRINTER
Section 2 (PJL Set Commands)
@PJL SET RESOLUTION=600
@PJL SET COPIES=1
Section 3 (PCL Code used to invoke PCL Language)
@PJL ENTER LANGUAGE=PCL
Section 4 (PCL Data Stream or ASCII Document inserted here for Options such as
selection Different Fonts, Simplex, Duplex, etc.)
,,,,,,,,,,
Section 5 (Closing Command, Required at end of Document)
<ESC>%-12345X@PJL EOJ
Sample PJL Headers
This section contains examples of these commands in use.
Example 1 Simple Print
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL COMMENT Beginning PCL Job<CR><LF>
@PJL SET OUTBIN=MAINTRAY<CR><LF>
@PJL SET QTY=1<CR><LF>
@PJL SET RESOLUTION=600<CR><LF>
@PJL SET JOBATTR="@JOAU=John"<CR><LF>
Example 2 Finishing Options (Stapling)
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=OUTBIN101<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET STAPLE=TOPLEFT<CR><LF>
dc08cc0440
Customer Support Page 9

Example 3 Finishing Options (Punch)
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=OUTPIN101<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET PUNCH=LEFT<CR><LF>
@PJL SET JOBATTR="@PNHN=TWO"<CR><LF>
Example 4 Finishing Options (Saddle stapling and folding)
It is an example of division in every 5 sheets.
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=ON<CR><LF>
@PJL SET STAPLE=SADDLE<CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>
@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
@PJL SET JOBATTR="@BKDN=5"<CR><LF>
Example 5 Finishing Options (Bi-Folding(multi page))
It is an example of division in every 5 sheets.
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=NONE<CR><LF>
@PJL SET STAPLE=NONE <CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>
@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
@PJL SET JOBATTR="@BKDN=5"<CR><LF>
@PJL SET QTY=1<CR><LF>
Example 6 Finishing Options (Bi-Folding(single page))
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>
@PJL SET FINISH=NONE<CR><LF>
@PJL SET STAPLE=NONE <CR><LF>
@PJL SET JOBATTR="@FOLD=BIFOLDINSIDE"<CR><LF>
@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>
Example 7 Proof Print
<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>
@PJL SET HOLD=PROOF <CR><LF>
@PJL SET USERNAME="John" <CR><LF>
@PJL SET JOBNAME="Job1" <CR><LF>
dc08cc0440
Customer Support Page 10