Xerox WorkCentre M24 Color Service manual

SA Guide -- WorkCentre M24
Product Overview
Start Install Steps
WorkCentre M24 SA Guide
Network
Connectivity Print Drivers Enabling Scanning Scan to E-mail and Fax Internet Services Trouble shooting Trademarks & Notices
Welcome to the WorkCentre M24 guide for System Administrator's.
This guide will help you install printing and other optional services on your network.
Click here to begin.
Click here for a Quick Install page.
(Use your browser's Print function to print it for reference.)
Click here for instructions on using this guide.
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/index.htm [9/4/03 8:32:24 AM]

Product Overview
WorkCentre M24 Product Overview
Standard Features
Options
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Specifications.htm [9/4/03 8:32:26 AM]

Standard Features
Standard Features
●Printer engine with Integrated controller
●Scanner with Stand
●Duplex Automatic Document Feeder (DADF)
●Standard High Capacity A4 Tray
●Electronic Pre-Collation (EPC)
●Face-Up Output Tray
●Offset Catch Tray
●Scan to mailbox
●600x600; 600x1200 & 1200x1200 printing resolution -
200x200; 300x300 & 600x600 copying resolution
●EA1 toner - No Oil Required! - No Streaks
●SRA3 / 12x19", 64x220 gsm / 16-110 lb index media - Full Bleeds on A3/11x17"
●Up to 3,140 sheet capacity
●Excellent Reliability of 3 calls/year at 7K AMPV; 1.2 hours MSH
●45 sec warm-up; 7 sec color FCOT
●Fuser Belt Module
●Token Ring - Not Available
Return to Product Overview Menu Proceed to Options
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/StdFeatures.htm [9/4/03 8:32:26 AM]

Options
Options
●1000 Sheet Finisher (stapler)
●Base Machine with stand (see below)
●Tandem Tray (see below)
●Three Tray Module (see below)
Base Machine with Stand
(Shown with optional
DADF and Finisher.)
Three Tray Module Tandem Tray Module
Return to Product Overview Menu
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/options.htm [9/4/03 8:32:27 AM]

SA Guide -- WorkCentre M24
Welcome to the WorkCentre M24 guide for System Administrator's.
This guide will help you install printing and other optional services on your network.
Click here to begin.
Click here for a Quick Install page.
(Use your browser's Print function to print it for reference.)
Click here for instructions on using this guide.
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/GuidePage.htm [9/4/03 8:32:27 AM]

Step 1 - Install
Installation
Step 1. Connect one end of a Category 5 twisted pair cable to a live network drop. Connect the opposite end
of the cable to the RJ-45 socket at the rear of the Printer.
Click to continue
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_1.htm [9/4/03 8:32:27 AM]

Step 2 - Install
Installation
Step 2. Set the printer's power switch to ON and wait until the Main (multiple tabbed) screen is displayed.
Click to continue
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_2.htm [9/4/03 8:32:27 AM]

Step 3 - Install
Step 3.
Follow the procedure outlined below to print a Settings List.
To print a copy of this procedure, go to the Network Connectivity tab of the guide and select
Settings List.
You can then use your browser's Print function to print the procedure.
Settings List
To print a Settings List, with the Printer switched ON, perform the following steps:
1. Press the Machine Configuration (Confirmation) button. This is the lowest of the three square
buttons to the immediate left of the Control Panel’s numeric keypad.
2. Press the Billing Meter/Print Report Tab on the Control Panel’s touch screen. This is the second Tab
from the left side of the screen.
3. Press the Print Report/List button. This is the lowest of the two buttons displayed vertically on the
touch screen.
4. Press the Copy Mode Settings button. This is the center button in the upper row of three buttons
displayed horizontally on the touch screen.
5. Press the Square (Settings List) button displayed by itself on the screen.
6. Press the large, green, Start button, located to the immediate right of the Control Panel’s numeric
keypad.
7. The printing process will be graphically displayed on the touch screen. Upon receipt of the Settings List,
note that the three page print is formatted into two columns with horizontal ruled lines indicating four
distinct data display areas on the print. The first area displays System Settings. The second area
displays Copy Settings. The third area displays Print Settings. The fourth area displays
Communication Settings.
Click to continue
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_3.htm [9/4/03 8:32:27 AM]

Step 4 - Install
Step 4:
Network
Connectivity
All of the instructions referenced below are obtained by first opening the Network
Connectivity Tab. Use the Back function of your browser to return to this step, should you
go to any of the referenced procedures now.
Refer to the Settings List and verify that the appropriate ports and protocols are enabled for your Network
environment.
Verify the following:
●The TCP/IP protocol stack should be enabled to support communicating with the Printer's Internet
Services. The Printer should also have a valid IP Address, Subnet Mask, and Gateway. If this is not the
case, select NOS Selection Menu, click TCP/IP Protocol Configuration, and follow the instructions
supplied.
●If Internet Services on the Printer is shown as "disabled" on the Settings List, follow the instructions to
Enable Internet Services.
●If you will be using SNMP Management software with this printer, select SNMP Configuration and
follow the instructions supplied.
●If you will be using the Parallel Port and wish to view or change its configuration, select Parallel Port
Configuration and follow the instructions supplied.
Follow the instructions referenced for performing necessary configurations.
Click to continue
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_4.htm [9/4/03 8:32:28 AM]

Network Connectivity Menu
Network
Connectivity
Install Steps A1
Settings List A6
Ethernet Speed Setting A2
Enable Internet Services A9
Parallel Port Configuration A7
SNMP Configuration A8
NOS Selection Menu
Changing the Administrator Password A10
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/NetConnectMenu.htm [9/4/03 8:32:28 AM]