Xiaomi G9 Plus User manual

Vacuum Cleaner G9 Plus User Manual

1
Safety Instructions
This product is for household use only. Read this manual carefully before use, and retain it for future reference.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Do not use the product at an ambient temperature above 38°C or below 5°C or on a floor with liquids or sticky substances.
If the charger or battery pack is damaged, it must be replaced by a special cord or assembly available from the manufacturer or
its service agent.
To reduce the risk of fire, explosion, or personal injury, check to make sure the lithium-ion battery and charger are undamaged
before use. Do not use the vacuum cleaner if either the battery or charger is damaged.
Only use the vacuum cleaner on dry indoor surfaces. Do not install, charge, or use this product outdoors, such as in bathrooms,
or near a pool.
Do not touch the plug or any part of the vacuum cleaner with wet hands.
The high torque brush bar, mini electric brush, battery, extension rod, and the vacuum cleaner are electrically conductive and
should not be immersed in water or other liquid. Make sure all parts are thoroughly dry after you carry out cleaning on them.
To prevent injury caused by moving parts, turn off the vacuum cleaner before cleaning the high torque brush bar and mini electric
brush. The high torque brush bar, dust compartment, and filter must all be properly installed before using the vacuum cleaner.
Do not use the vacuum cleaner to pick up flammable or combustible liquids, such as gasoline, bleach, ammonia, or drain cleaners;
nor other liquids like water.
Do not use the vacuum cleaner to pick up drywall particles, ashes like fireplace ash, or smoking or burning materials such as coal,
cigarette butts or matches.
Do not use the vacuum cleaner to pick up sharp or hard objects, such as glass, nails, screws, or coins, which may damage the product.

2
Keep hair, loose clothing, fingers, and other parts of the body away from the vacuum cleaner's openings and moving parts. Do not
point the suction opening, extension rod, or other accessories at your eyes or ears or put them in your mouth.
Do not put any object into the vacuum cleaner's openings, nor use the vacuum cleaner with any opening blocked. Keep free of
dust, lint, hair, or other items which may reduce airflow.
Do not rest the vacuum cleaner against a chair, table, or other unstable surfaces, as this may cause damage to the product or
personal injury. If the vacuum cleaner malfunctions because of being knocked over or damaged, please contact the authorized
service department. Never attempt to disassemble the vacuum cleaner on your own.
The dust compartment cover, pre-filter, cyclone assembly, and filter must all be properly installed prior to using the vacuum cleaner.
Make sure the charger is unplugged when not used for extended periods as well as prior to performing any maintenance or repairs.
Please be extra careful when using the vacuum cleaner to clean stairs.
Fire Hazard Warning: Do not apply any type of fragrance to the vacuum cleaner's filter. These types of products are known to
contain flammable chemicals which may cause the vacuum cleaner to catch fire.
DO NOT expose the battery and appliance to fire as it may cause explosion.
DO NOT expose or submerge the battery and appliance in any water, salt water, or other liquids.
WARNING: Do not use any third-party battery pack and charger.
Use only with BLJ24W308080P-V charger.
Use only with V2209-7S1P-BCA battery pack.
Please strictly follow the instructions in this user manual when using the vacuum cleaner. Users are responsible for any loss or
damage that may arise from improper use of the vacuum cleaner.

3
Product Overview
Accessories List
Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to
product enhancements.
2-in-1 Crevice Nozzle
High Torque Brush Bar Mini Electric Brush
Extension Rod Charger
Storage Mount
(includes screw × 2, wall plug × 2, and mounting template sticker)

4
Battery Status Indicator
Charging Port
Power Button
Press: Turn on
Release: Turn off
Suction Level Switch
High Power
Standard
Eco
Component Name
Dust Compartment
Release Switch
Dust Compartment
Bottom Cover Release
Button
Dust Compartment
Battery Release Button

5
Installing the Accessories onto the Vacuum Cleaner
How to Install
Insert until it clicks into place
Note: Mini electric brush should not be used with the extension rod.

6
Note: The storage mount should be installed in a cool, dry place with an
electrical outlet nearby. Prior to installing, ensure that there are not any wires
or pipes in the space directly behind where the mount will be installed.
Installing the Storage Mount
1. Paste the mounting template sticker on the wall. Make sure that the bottom
edge of the sticker is parallel to and about 107 cm from the ground.
2. Use a power drill with an 8 mm drill bit to drill holes in the wall according to
the positions of the holes on the mounting template sticker. Then uses the
screws and wall plugs to install the storage mount.
Recommended Height: At least 1.07 meters from the ground
Baery Status Indicator
Charging
Once the vacuum cleaner is fully charged, the indicator will turn off after 5
minutes, and the vacuum cleaner will then enter the energy-saving mode.
Low battery
Note: means off, means on, and means blinking.
Fully chargedHalf battery
Nearly full
Battery Status
Indicator
Notes:
Fully charge the vacuum cleaner before using it for the first time. This will take
about 3.5 hours.
The vacuum cleaner cannot be used while charging.
Vacuuming at the highest suction level for a prolonged period will cause the
battery to heat up, which may increase the charging time. Before charging the
vacuum cleaner, it is better to cool it down for 30 minutes.
107 cm

7
Using Different Accessories
Note: The high torque brush bar can
be attached directly to the vacuum
cleaner.
High Torque Brush Bar: For cleaning
different types of flooring such as
wood, marble, tile, and carpet.
How to Use
Notes:
If any rotating part becomes stuck, the vacuum cleaner may shut off automatically.
Remove any trapped foreign objects, then resume use.
When the high-temperature protection for the battery is triggered, the vacuum
cleaner will automatically stop working. Wait until the battery temperature returns
to normal, then resume use.
Note: Do not put the vacuum
cleaner alone on the storage mount.
Place it on the storage mount after
connecting it with the extension rod
and the high torque brush bar.
Storage Mount: The vacuum cleaner
can be placed on the storage mount
when it is not in use.
Note: Press the release button on the 2-in-1 crevice nozzle to adjust the position
of the brush to meet your cleaning needs.
2-in-1 Crevice Nozzle: Suitable for vacuuming hard-to-reach places, such as
corners of doors, windows, walls, and stairs, as well as sofas and table surfaces.
Mini Electric Brush: For vacuuming dirt, pet hair, and other stubborn debris from
sofas, bedding, and other fabric surfaces.

8
Care & Maintenance
Always use genuine parts to keep your warranty from being voided.
If the filter, extension rod, or high torque brush bar becomes clogged, the
vacuum cleaner will stop working shortly. To restore its functionality, clean
the clogged component.
If the vacuum cleaner will not be used for an extended period, fully charge
it and disconnect it from the power then store it in a cool, low-humidity
environment away from direct sunlight. To avoid over-discharging the battery,
recharge the vacuum cleaner at least once every three months.
Maintenance Precautions
Wipe the vacuum cleaner with a soft, dry cloth.
Cleaning the Vacuum Cleaner
Cleaning the Dust Compartment, Pre-filter, and Cyclone
Assembly
1. The vacuum cleaner's cleaning ability will be reduced if the dust
compartment is filled to the "MAX" mark. To regain performance, empty the
dust compartment in a timely manner. Before emptying the compartment,
make sure the vacuum cleaner is disconnected from the power, and do not
press its power button.

9
2
1
2. Press the dust compartment bottom cover release button, then empty the
contents.
3. Pull the dust compartment release switch in the direction illustrated in
image , then remove the dust compartment from the vacuum cleaner as
illustrated in image .
Dust Compartment Release Switch

10
4. Remove the pre-filter first, then lift the handle of the cyclone assembly
and turn to counterclockwise until it stops, then pull to lift out the cyclone
assembly.
1
2
Pre-filter
5. Rinse the pre-filter, cyclone assembly, and dust compartment with water
until they are clean, then set each component aside to thoroughly dry for at
least 24 hours.
Notes:
The dust compartment should be rinsed out at least once a month.
The pre-filter and cyclone assembly should be cleaned once every 3 to 4
months.
Pre-filter Cyclone Assembly Dust Compartment

11
6. Wipe the contact points of the vacuum cleaner with a soft dry cloth if they
are dirty.
Do not use detergents, polishes, or air fresheners to clean the dust
compartment.
Do not clean the dust compartment, pre-filter, or cyclone assembly in a
dishwasher or washing machine, nor attempt to dry any component in a
tumble dryer, oven, microwave, or near an open fire.
Notes: 1. Insert the cyclone assembly vertically into the dust compartment, and make
sure that the handle of the cyclone assembly line up with the slot on the left
side of the dust compartment. Turn the handle clockwise until it locks, then
flip the handle down.
2. Place the pre-filter with its front side facing up into the cyclone assembly.
Installing the Dust Compartment, Pre-filter, and Cyclone
Assembly
2
1Pre-filter

12
3. Slightly tilt the dust compartment so its slot aligns with the clip on the
vacuum cleaner. Then gently push the dust compartment until it clicks into
place.
1
2Insert until it
clicks into place
Cleaning the Filter
1. Remove the dust compartment as shown in the figure.
1
2
Dust Compartment Release Switch
It is recommended to clean the filter once every 4 to 6 months.
It is recommended to replace the filter once every 6–12 months according
to the actual using condition of the filter.
Notes:

13
2. Remove the filter from the vacuum cleaner by pulling it down in the direction
shown in the figure.
3. Clean the filter with clean water. Make sure you rotate the filter 360° to
thoroughly remove all dust caught in the filter. Lightly tap the filter several
times to remove any excess dirt.
Notes:
Only use clean water to clean the filter. Do not use detergent.
Do not attempt to clean the filter with a brush or finger.
4. Allow the filter to thoroughly dry for at least 24 hours.
1. Insert the filter into the vacuum cleaner and gently press down, as illustrated.
Installing the Filter

14
1
2
2. Reinstall the dust compartment.
Insert until it clicks
into place
Cleaning the High Torque Brush Bar
2. Use scissors to cut and pick out any hair or other debris tangled around the
roller brush. Wipe away excess dust from the slot and clear plastic cover
using a dry cloth or paper towel.
1. Turn the lock counterclockwise until it stops, then remove the roller
brush from the high torque brush bar.

15
3. After extended use, the roller brush may become dirty and should be washed.
After washing, allow the roller brush to dry thoroughly by standing it upright
in a well-ventilated area for at least 24 hours.
4. Make sure the roller brush is completely dry, and then align the lock on the
top of the roller brush with to reinsert it. Turn the lock clockwise to to
install the roller brush in place.
1. Use a proper tool to turn the lock counterclockwise until you hear a click.
2. After unlocking the roller brush, remove it from the mini electric
brush, then rinse and clean the roller brush.
Cleaning the Mini Electric Brush

16
3. After washing, allow the roller brush to dry thoroughly by standing it upright
in a well-ventilated area for at least 24 hours.
4. Once the roller brush is dry, reinstall it by following the disassembly steps in
reverse.
The vacuum cleaner contains a removable rechargeable lithium-ion battery
pack which has a limited number of recharge cycles. After extended use, the
battery pack may no longer hold a charge. If this happens, it means the battery
pack has reached the end of its life cycle and needs to be replaced.
Baery Pack
1. Press down the battery pack release button and slide the battery pack to the
right, as illustrated, to remove it.
2. Install the new battery pack.

17
Specifications
Cordless Vacuum Cleaner
Model B206 Rated Voltage 25.2 V
Charging Voltage 30.8 V Battery Capacity 2500 mAh (Nominal Capacity)
2400 mAh (Rated Capacity)
Rated Power 400 W Dust Compartment Capacity 0.6 L
Charging Time Approx. 3.5 hours Net Weight 3.4 kg
Item Dimensions 1286 × 214 × 256 mm
High Torque Brush Bar Mini Electric Brush
Model G9-01 Model 1C-02
Rated Power 40 W Rated Power 20 W
Rated Voltage 25.2 V Rated Voltage 25.2 V
Charger
Manufactured by Zhongshan Baolijin Electronic Co., Ltd. Average Active Efficiency 87.5%
Model BLJ24W308080P-V Efficiency at Low Load (10%) 77.9%
Input 100–240 V~ 50/60 Hz 0.8 A No-load Power Consumption 0.10 W
Output 30.8 V 0.8 A
Rechargeable Lithium-ion Baery Pack
Model V2209-7S1P-BCA Nominal Capacity 2500 mAh
Nominal Voltage 25.2 V Rated Capacity 2400 mAh
Energy 60.48 Wh

18
Regulatory Compliance Information
The lithium-on battery pack contains substances that are hazardous to the environment. Before disposing of the vacuum cleaner, please first remove the battery
pack, then discard, or recycle it in accordance with local laws and regulations of the country or region it is used in.
Under abusive conditions, liquid may be ejected from the battery. Avoid contact with liquid, as it may cause irritation or burns. If contact occurs, flush with water. If
liquid contacts eyes, seek medical help.
We Dreame (Tianjin) Information Technology Co., Ltd., hereby, declare that this equipment is in compliance with the applicable Directives
and European Norms, and amendments. The full text of the EU declaration of conformity is available at the following internet address:
http://www.mi.com/global/service/support/declaration.html
For detailed e-manual, please go to www.mi.com/global/service/userguide
WEEE Information
EU Declaration of Conformity
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with
unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated
collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and
recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for
more information about the location as well as terms and conditions of such collection points.
Baery Safety Precautions

19
Troubleshooting
Issue Possible Cause Solution
The vacuum cleaner does not work.
It is out of battery or has low battery. Fully charge the vacuum cleaner, then resume use.
It enters into overheat protection mode triggered
by a blockage.
Clear any blockages and restart the vacuum
cleaner when it cools down.
Its suction opening or airway passage is blocked. Clear any blockages from suction opening or
airway passage.
The suction power reduces.
The dust compartment is full and/or the filter is
clogged. Empty the dust compartment and clean the filter.
The high torque brush bar, the extension rod, or
other parts are blocked.
Clear any blockages from the high torque brush
bar, the extension rod, or other parts.
The motor makes a strange noise. The main suction opening or the extension rod is
blocked.
Clear any blockages in the main suction opening or
the extension rod.
The battery indicator does not light up while
charging.
The charger is not connected to the vacuum
cleaner. Make sure the charger is plugged in correctly.
The battery is fully charged and went into sleep
mode. The vacuum cleaner can be used normally.
If the problem still persists after ruling out the above two possibilities, please contact after-sales service
for help.
The battery charges slowly. The battery temperature is too low or too high. Wait until the battery temperature normalizes,
then resume use.