Xiaomi Truclean W10 Pro B302GL User manual

Truclean W10 Pro Wet Dry Vacuum User Manual

Safety Instructions
This product is for household use only. Read this manual carefully before use, and retain it for future reference.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
This appliance contains batteries that are only replaceable by skilled persons.
The appliance is only to be used with the power supply unit provided with the appliance.
Do not touch the plug or any part of the vacuum with wet hands.
This vacuum is for indoor use only. Do not use or install it in outdoor, industrial, or sommercial environments. Do not use the self-cleaning charging dock in humid environments such as bathrooms.
A hazard may occur if the appliance runs over the supply cord.
The plug must be removed from socket-outlet before cleaning or maintaining the appliance.
EU Declaration of Conformity
We, Beijing Shuanzao Technology Co., Ltd., hereby declare that this equipment is in compliance with the applivable Directives and European Norms, and amendments. The full text of the EU declaration of conformity is available
at the following internet address: http://www.mi.com/global/service/support/declaration.html
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions such collection points.
To reduce the risk of fire, explosion, or personal injury, check before use to make sure the power supply is undamaged. Do not use the vacuum if the power supply is damaged.
Do not immerse the vacuum or the self-cleaning charging dock in water or other liquids for cleaning.
Clean the dirty water tank in time to avoid the decrease of suction and overheating of the motor caused by obstruction. Otherwise, the service life of the vacuum may be affected. Do not use the
vacuum if the roller brushbar, the dirty water tank, and the filter are not installed in place.
Make sure to turn off the vacuum before cleaning or replacing the roller brushbar.
Neither use the vacuum cleaner to pick up flammable or explosive liquids such as gasoline, nor other liquids such as water or toxic liquids like bleach, ammonia, and drain cleaners.
Do not use the vacuum to clean up toner used in laser printers and copiers, as toner may cause fire or explosion.
Do not use the vacuum to pick up smoking or burning materials such as charcoal, cigarette butts, or matches.
Do not use the vacuum to pick up sharp or hard objects, such as glass, nails, screws, or coins, which may demage the vacuum.
Do not use the vacuum to clean stains of thick oily substances, strong adhesives, or dyes, such as shoe polish, paints and pigments.
Keep hair, loose clothing, fingers, and other parts of the body away from the vacuum‘s openings and moving parts.
Do not put any objects into the vacuum‘s openings, nor use the vacuum any opening blocked. Keep free of dust, lint, hair, or other items which may reduce airflow.
Do not shake the vacuum up and down or hit it violently to prevent dirty water from flowing into the motor.
Do not lift or move the vacuum while the motor is operating, nor tilt it to one side to prevent dirty water from entering the motor.
Do not place the vacuum on unstable surfaces such as chairs or tables to prevent damage or personal injury caused by its falling of. If the vacuum malfunctions because of being knocked over or
damaged, please contact the authorized service department. Never attempt to disassemble the vacuum on your own.
Do not charge or store the vacuum near heat sources or in humid areas, such as by a radiator or in a kitchen or bathroom.
Only use replacement parts that are approved by Xiaomi.
Do not repair the vacuum on your own when it breaks down or has problems like electric leakage, overheating motor, making unusual sounds, overheating main body, giving off odors, or weak
suction.
Keep the cleaning brush out of reach of children.
Please be extra careful when using the vacuum to clean stairs.
Do not apply any type of fragrance to the vacuum‘s filter. These types of products are known to contain flammable chemicals which may cause the vacuum to catch fire.
Strictly follow the instructions in this user manual to charge the vacuum at an ambient temperature of 6˚C to 40˚C. Improper charging may result in damage to the battery.
Please strictly follow the instructions in this user manual when using the vacuum. Users are responsible for any loss or damage that may arise from improper use of the vacuum.
For detailed e-manual, please go to www.mi.com/global/service/userguide.
Do not use any third-party battery or power supply. Only use the BLJ24WD260090P-V power supply provided with the appliance.
WARNING:
Regulatory Compliance Information

Handle Roller Brushbar Cover
(Pre-installed)
Filter
(Pre-installed)
Vacuum
Self-cleaning
Charging Dock
Power Supply Accessory Container Mounting Clip
Clean Water Tank
(Pre-installed)
Dirty Water Tank
(Pre-installed)
Roller Brushbar Holder Roller Brushbar
Mop Pad
Cleaning Brush
(Rotate the handle of the cleaning brush to
remove blade)
Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.
Accessories for Installing on the Self-cleaning Charging Dock Other Accessories
Accessories for installing on the Vacuum
Accessory List

Product Overview
Vacuum Display
Self-cleaning Button:
When the vacuum is
charging and its battery
level is equal to or over 10 %,
press to enable or disable
the self-cleaning.
Handle Release
Button
Auxiliary Wheel
Voice Button:
Press to change
languages.
Press and hold
for three seconds
to enable/disable
voice notification.
Dirty Water
Tank Release
Button
Dirty Water
Tank
Roller
Brushbar
Lock
Clean Water Tank
Release Button
Clean Water Tank
Roller Brushbar
Cover Release
Button
Roller Brushbar
Display
Handle
Power Button:
Press to turn on/off the
vacuum.
Press to switch mode during
cleaning.
Mode Button:
Battery Level
Indicator
Insufficient
Water in the
Clean Water
Tank
Full Dirty
Water Tank
Auto Mode
Water
Absorbing
Mode
Dirtiness/Error
Indicator
Common
Error
Tangled
Roller
Brushbar
Self-cleaning
Mode
Turbo Mode
Dirtiness/Error Indicator
Green: Clean
Yellow: Dirty
Orange: Very dirty
Red: Error

Charging
Contacts
Place Cleaning Brush Here
Place Roller Brushbar Here
Place Filter Here
Power port
Mounting Clip
Installation Slot
Water Inlet
Water Tank Plug
Dust Compartment Release Button
Dust Compartment
Water Level Sensor
Dirty Water Tank
Dirty Water Tank
Self-cleaning Charging Dock Clean Water Tank

Installing the Roller Brushbar
How to Install
Warning: Turn on the vacuum after installing the roller brushbar onto the floor brush and
making sure it is secured in place.
1. Pinch both roller brushbar cover release buttons to remove the roller brushbar cover.
2. Remove the inner holder inside the roller brushbar mop pad.
Roller Brushbar
Mop Pad Inner Holder
3. Hold the roller brushbar holder by its upper part, put into the roller brushbar mop pad, and
press them into place.
4. Install the roller brushbar onto the floor brush, and turn the roller brushbar lock to the locked
position. Then reinstall the roller brushbar cover.

Installing the Handle
Insert the handle into the vacuum. The handle is installed when you hear a click.
Caution: Make sure that the handle is secured in place after installation.
To remove the handle, use a non-sharp tool, such as a chopstick, to press and hold the
handle release button on the back of the vacuum, and simultaneously pull the handle
upwards vertically.
Installing the
Handle
Click
Removing the Handle
3. Installing the Accessory Container
Install the accessory container onto
the mounting clip.
1. Installing the Power Cord
Plug the power cord into the power port at
the bottom of the self-cleaning charging
dock, then wind and store the excess
power cord.
Installing the Self-cleaning Charging Dock
2. Installing the Mounting Clip
Install the mounting clip onto the
installation slot on either side of the
bottom of the self-cleaning charging dock.
4. Storing the Accessories
The container can store the cleaning
brush, the roller brushbar, and the filter.
Note:
The spare roller brushbar and the spare
filter need to be purchased separately.

5. Connecting to an Electrical Outlet
Place the self-cleaning charging dock on a flat surface and connect it to
power via the power supply.
Note:
Do not place the self-cleaning charging dock near heat sources or in humid
areas, such as by a radiator, in a kitchen, or in a bathroom.
6. Charging on the Self-cleaning Charging Dock
After the self-cleaning charging dock is plugged in, align the charging contacts at the
bottom of the vacuum‘s floor brush with the charging contacts on the dock. The vacuum
starts charging when you hear the voice prompt.
Notes:
The number on the display represents
the current battery level in a
percentage during charging.
The display will go out if no operation
is performed in 20 seconds after the
charging is completed.
Notes:
Fully charge the vacuum before first use and after each use. The total charging time is about 5 hours.
Working at the turbo mode for a prolonged period will cause the battery to heat up, and the charging
time may increase or the battery level may not grow in a short time during charging. This is normal.

1. Press the clean water tank release button, and simultaneously pull the tank out.
2. Open the clean water tank plug, slowly fill the tank with clean water up to the maximum water
level mark, and insert the plug back. Then reinstall the clean water tank to the vacuum. It is
secured in place when you hear a click.
Click
MAX
Note: Do not add hot water or disinfectant to avoid damaging the vacuum and other components.
Remove the vacuum from the self-cleaning charging dock, step on the floor brush with one
foot and pull back the handle to tilt the vacuum.
Press the button to turn on the vacuum.
Turning on
Water Adding
How to use

Switching Modes
Press the button to cycle through the modes of auto, water absorbing, and turbo.
Auto Mode Water Asorbing Mode Turbo Mode
Daily stains cleaning Water stains cleaning
(not for vacuuming dust) Stubborn stains cleaning
Do not rotate the vacuum from side to side while lying it down for cleaning to prevent the floor
brush from tilting up or dirty water from running out.
CAUTION:
Pausing/Turning off
Hold the vacuum in the
upright position to puse
cleaning, or press the
button to turn off the
vacuum. To avoid dirty
water residues, the vacuum
will continue running for a
few seconds before turning
off. Place the vacuum back
onto the self-cleaning
charging dock after it
completely stops working.
When the vacuum is
paused in the upright
position or turned off, pull
the handle backward, and
push the vacuum to the
self-cleaning charging dock
with the help of wheels.
Then you can use the dock
for storage, charging, and
self-cleaning.
Notes:
Put the vacuum back
onto the self-cleaning
charging dock properly
after using it to prevent
the vacuum from tipping
over due to improper
placement.
Do not lift the vacuum
vertically as illustrated to
prevent dirty water from
flowing out.

The vacuum can be used to clean different types of hard-surface flooring
such as wood, tile, and marble.
The vacuum can be placed flat at 180° for cleaning the floor underneath the furniture.
Using Scenarios
Cautions:
Do not use the vacuum on fabric surfaces, such as carpets and blanets.
Do not tilt the vacuum forward or shake it violently while cleaning to avoid dirty water flowing
into the vacuum and thus damaging it.

Care & Maintenance
Clean and maintain the relevant components when the vacuum is paused in the upright
position or turned off.
Move the self-cleaning charging dock away before cleaning the vacuum.
Maintenance Frequency
Replacement Frequency
Component
Dirty water tank components (including the dirty water
tank, the dust compartment, and the water level sensor) Clean after each use.
Dirty water outlet pipeline (including the dirt
detection sensor)
Water & air separator
Floor brush (overall)
Roller brushbar
Filter
Self-cleaning charging dock
Recommended
Maintenance Frequency
Clean when prompted by
relevant voice notification.
1-3 months
Clean once a week, depending
on the dirtness.
Self-cleaning is required after
each use.
Clean once a week.
Clean once a week.
The following recommended replacement frwquencies are for reference only. Components should
be replaced promptly if damaged.
Component Recommended Replacement Frequency
Roller Brushbar
Filter
3-6 months
6-12 months
Self-cleaning
When the vacuum is charging and its battery level is equal to or more than 10%, press to
start self-cleaning.
Press the button or the button to stop self-cleaning.
Based on how dirty the roller brushbar is, it will take about 2 to 3 minutes for the vacuum to
complete the self-cleaning.
Notes:
Clean the dirty water tank in time after self-cleaning to prevent odors.
It is recommended to remove the roller brushbar after self-cleaning and place it in the
accessory container for drying to prevent odors.
It is recommended to regularly clean parts that cannot be cleaned by self-cleaning, such as
the roller brushbar cover and the parts around the custion port.

1. Press the dirty water tank release button, and simultaneously pull the tank out.
Dust Compartment
Water Level Sensor
Dirty Water Tank
2. Hold the lower end of the dirty water tank with one hand, press the dust compartment release
button with the other, and remove the dust compartment upwards. Then empy the dust and
dirty water respectively.
3. Rinse the dirty water tank, the dust compartment, and the water level sensor until they are
clean.
Notes:
The cleaning brush can be used to assist in cleaning.
The water level sensor should be cleaned frequently to avoid the detection accuracy being
affected by the stains adhered to the sensor.
4. Put the dust compartment back, then reinstall the dirty water tank onto the vacuum. The tank
is secured in place when you hear a click.
Cleaning the Dirty Water Tank
Click

Cleaning the Floor Brush
1. Pinch both roller brushbar cover release buttons to remove the roller brushbar cover.
Note:
Do not remove the roller brushbar while the vacuum is on the self-cleaning charging dock.
2. Turn the roller brushbar lock counterclockwise until is unlocked, and pull the roller brushbar
outward.
3. Rotate the handle of the cleaning brush to remove the blade. Use the blade to cut the hair
tangled on the roller brushbar and the floor brush.

4. Use tap water to rinse the roller brushbar and its cover until they are clean, and then put
them in the accessory container for drying to prevent odors.
Note: Do not expose the roller brushbar to direct sunlight.
5. Use a dry cloth or paper towel to remove the hair, dirt, and foreign objects blocked at the suction
port.
Notes:
Do not rinse the floor brush directly.
Do not touch the gearbox right after using the vacuum to avoid scalds.
Gearbox
Click
6. Reinstall the roller brushbar and its cover in order. When reinstalling the roller brushbar cover,
align it with the mounting position, and it is secured in place when you hear a click.

It is normal to find a small amount of dirty water around the water & air separator after removing
the dirty water tank. Please wipe the dirty water away.
Pull out the filter from the top left corner of the dirty water tank‘s mounting slot as illustrated.
Rinse the filter clean under tap water, then dry it or put it in the accessory container to dry
before reinstalling to prevent odors.
Take out the dirty water tank, and use the cleaning brush to clean the dirt detection sensor and
the pipeline of the dirty water outlet.
Cleaning the Water & Air Separator Cleaning the Dirt Detection Sensor
Cleaning the Filter

Cleaning the Self-cleaning Charging Dock Cleaning the Vacuum
Disconnect the self-cleaning charging dock from the power supply before cleaning the dock.
Use a dry cloth or paper towel to clean the dust from the self-cleaning charging dock.
Note:
Do not rinse the self-cleaning charging dock directly with water to prevent short circuits.
Stand the vacuum upright, and use a dry cloth or paper towel to clean the dust from the
vacuum.

The display will show an error message or a voice notification will be played when the vacuum is
not working normally, please refer to the table to find the solution. If the error cannot be solved
by the solution, please contact the after-sales service team in time.
The clean water tank is short of
water, please add water.
Add water to the clean water tank
before use.
The roller brushbar is tangled
with foreign objects, please
check and clean it.
The dirty water tank is full,
please clean it.
Reinstall the roller brushbar.
Check and clean the roller brushbar.
Clean the dirty water tank and
reinstall it.
Reinstall the roller brushbar properly.
The air vent is blocked, please
clean the pipeline and the dirty
water tank.
The sensor is dirty, please clean
the pipeline of the vacuum.
The vacuum malfunctions, and
it has voice alert with error
code.
Check whether the suction port of
the floor brush and the pipeline of
the dirty water outlet are blocked,
and clean the dirty water tank.
Clean the dirt detection sensor.
Contact the after-sales service team.
The vacuum does not work.
The vacuum cannot recycle
dirty water properly.
A false alert for a full dirty water
tank is triggered.
The vacuum cannot be
charged.
Please refer to the table below to find the troubleshooting for common issues.
The battery is depleted.
The battery has
overheating protection.
The vacuum has no voice
notification.
The vacuum cannot carry out
self-cleaning.
Clean water tank, dirty
water tank, or roller
brushbar is not installed.
The dirty water tank is full.
The clean water tank is
out of water.
The suction port of the
floor brush or the pipeline
of the dirty water outlet is
blocked.
The roller brushbar is
tangled with foreign
objects.
The filter is not installed.
The water level sensor is
dirty.
The self-cleaning charging
dock is not connected to
power.
The power supply being
used is not original.
The voice notification is
disabled.
The clean water tank is
out of water.
The clean water tank is
not installed.
The dirty water tank is full.
The dirty water tank is not
installed.
The battery is low or
depleted.
The self-cleaning charging
dock is not connected to
power.
Fully charge the vacuum before
use.
Try again after the battery
temperature returns to normal.
Install the clean water tank/
dirty water tank/roller brushbar
properly.
Clean the dirty water tank and
reinstall it.
Add water to the clean water
tank and reinstall the tank.
Clean the suction port of the
floor brush and the pipeline of
the dirty water outlet.
Clean the roller brushbar.
Install the filter before use.
Clean the water level sensor.
Use the original power supply to
charge the self-cleaning
charging dock.
Use the original power supply.
Press and hold the voice
button for three seconds to
enable voice notification.
Add water to clean water
tank and reinstall the tank.
Reinstall the clean water tank.
Clean the dirty water tank and
reinstall it.
Reinstall the dirty water tank.
Carry out self-cleaning when
the battery level is sufficient.
Use the original power supply
to charge the self-cleaning
charging dock.
Error Icon Voice Notification Solution
Common Issue Possible Cause Solution
Troubleshooting

Specifications Environmental Notice
CAUTIONS:
Xiaomi Truclean W10 Pro Wet Dry Vacuum
Self-cleaning Charging Dock
Power Supply
Name
Rated Voltage
Wet and Dry Vacuum Cleaner Model B302GL
21.6 V
26.0 VCharging Voltage
IP Class IPX4
Net Weight (Vacuum)
Rated Power
Net Weight
(with Accessories)
200 W
5,4 kg
6,4 kg
Name
Rated Input
Net Weight
Charging Dock
26.0 V 0.9 A
0,65 kg
Model
Rated Output
B302CN-JZ
26.0 V 0.9 A
Manufacturer
Model
Input
Output
Zhongshan Baolijin Electronic
Co., Ltd.
BLJ24WD260090P-V
100-240 V 50/60Hz 0.8 A
26.0 V 0.9 A 23.4 W
Average Active
Efficiency
Efficiency at Low Load
(10%)
No-load Power
Consumption
87.00%
79.20%
0.06 W
The lithium-ion battery pack contains substances that are hazardous to the environment.
Before disposing of the vacuum, please first remove the battery pack, then discard, or recycle it
in accordance with local laws and regulations of the country or region it is used in.
Before disposing of the vacuum, remove the battery first.
The vacuum must be turned off before removing the battery.
The battery should be disposed of safely.
Remove the entire battery pack together, and make sure not to damage the outer casing of
the battery pack to prevent short-circuiting or leakage of harmful substances.
In the event of a battery leak, avoid contact with the liquid. If the liquid enters the eyes, rinse
with plenty of water and seek medical attention immediately.
The battery should not be removed by non-professionals. Otherwise, it may lead to a short
circuit or other risks. It is recommended to send the product to the professional after-sales
service team or a government--approved recycling facility for removal.
1. Use a non-sharp tool to press and hold the handle release button on the back of the vacuum,
and simultaneously pull the handle upwards vertically.
2. Remove the dirty water tank.
3. Unscrew the display assembly to remove it.
4. Remove the rear cover of the vacuum by unscrewing the bottom cover, the front cover, and
the rear cover of the vacuum.
5. Unscrew the battery pack assembly to remove it.
6. Unscrew the top and bottom covers of the battery pack assembly and remove the top cover.
7. Unscrew the battery pack assembly, and unplug the battery pack to remove it.
Steps to Remove the Battery:

WARRANTY NOTICE
THIS WARRANTY GIVES SPECIFIC RIGHTS, AND YOU MAY HAVE OTHER RIGHTS CONVEYED BY LAWS OF YOUR COUNTRY, PROVINCE OR STATE. INDEED, IN SOME COUNTRIES, PROVINCES OR
STATES, CONSUMER LAW MAY IMPOSE A MINIMUM WARRANTY PERIOD. OTHER THAN AS PERMITTED BY LAW, XIAOMI DOES NOT EXCLUDE, LIMIT OR SUSPEND OTHER RIGHTS YOU MAY HAVE.
FOR A FULL UNDERSTANDING OF YOUR RIGHTS WE INVITE YOU TO CONSULT THE LAWS OF YOUR COUNTRY, PROVINCE OR STATE.
1. LIMITED PRODUCT WARRANTY
2. REMEDIES
3. HOW TO OBTAIN WARRANTY SERVICE
4. EXCLUSIONS AND LIMITATIONS
XIAOMI warrants that the Products are free from defects in materials and woekmanship under normal use and use in accordance with respective Product user manual, during the Warranty Period.
The duration and conditions related to the legal warranties are provided by respective local laws. For more information about the consumer warranty benefits, please refer to Xiaomi‘s official website
https:// www.mi.com/en/service/warranty/.
Xiaomi warrants to the original purchaser that its Xiaomi Product will be free defects in materials and workmanship under normal use in the period mentioned above.
Xiaomi does not guarantee that the operation of the Product will be uninterrupted or error free.
Xiaomi is not liable for damages arising from non-compliance with the instructions related to the use of the Product.
If a hardware defect is found and valid claim is recieved by Xiaomi within the Warranty Period, Xiaomi will either (1) repair the product at no charge, (2) replace the product, or (3) refund the Product,
excluding potential shipping costs.
To obtain warranty service, you must deliver the Products, in its original packaging or similar packaging providing an equal degree of Product protection, to the adress specified by Xiaomi. Except to the
extent prohibited by applicable law, Xiaomi may require you to present proofs or proof of purchase and / or comply with registration requirements before reciving warranty service.
Unless otherwise stipulated by Xiaomi, this Limited Warranty applies only to the Product, manufactured by or for Xiaomi and identifiable by tradearks, trade name or “Xiaomi” or “Mi” logo.
The Limited Warranty does not apply to any (a) Damage due to acts of nature or God, for example, lightning strikes, tornadoes, flood, fire, earthquake or other external causes; (b) Negligence; (c)
Commercial use; (d) Alterations or modifications to any part of the Product; (e) Damage caused by use with non-Xiaomi products; (f) Damage caused by accident, abuse or misuse; (g) Damage caused
by operating the Product outside the permitted or intended uses described by Xiaomi or with improper voltage or power supply; or (h) Damage caused by service (including upgrades and expansions)
performed by anyone who is not a representative of Xiaomi.
It is your responsibility to backup any data, software, or other materials you may have stored or preserved on the product. It is likely that the data, software or other materials in the equipment will be lost
or reformatted during the service process, Xiaomi is not responsible for such damage loss.
No Xiaomi reseller, agent, or employee is authorized to make any modification, extension, or addition to this Limited Warranty. If any term is held to be illegal or unenforceable, the legality or enforceability
of the remaining terms shall not be affected or impaired.
Except as prohibited by laws or otherwise promised by Xiaomi, the after-sales services shall be limited to the country or region of the original purchase.
Products which were not duly imported and/or were not duly manufactured by Xiaomi and/or were not duly acquired from Xiaomi or a Xiaomi‘s official seller are not covered by the present warranties. As
per applicable law you may benefit from warranties from the non-official retailer who sold the product. Therefire, Xiaomi invites you to contact the retailer from whom you purchased the product.
The present warranties do not apply in Hong Kong and Taiwan.
5. IMPLIED WARRANTIES
Except to the extent prohibited by applicable law, all implied warranties (including warranties of merchantibility and fitness for a particular purpose) will have a limited duration up to a maximum duration
of this limited warranty. Some jurisdictions do not allow limitations on the duration of an implied warranty, so the above limitation will not be applied in these cases.
6. DAMAGE LIMITATION
Except to the extent prohibited by applicable law, Xiaomi shall not be liable for any damages caused by accidents, indirect, special or consequential damages, including but not limited to loss of profits,
revenue or data, damages resulting from any breach of express or implied warranty or condition, or under any other legal theory, even if Xiaomi has been informed of the possibility of such damages.
Some jurisdictions do not allow the exclusion or limitation of special, indirect, or consequential damages, so the above limitation or exclusion may not apply to you.
7. XIAOMI CONTACTS
For customers, please visit the website: https://www.mi.com/en/service/warranty/
The contact person for the after-sale service may be any person in Xiaomi‘s authorized service network, Xiaomi‘s authorized distributors or the final vendor who sold the products to you. If in doubt please
contact the relevant person as Xiaomi may identify.