Xirrus XR-320 User manual

Quick Installation Guide for XR-300 Models
The Xirrus XR-320 is a 2x2 802.11ac indoor wall access point (AP) with two fixed-band radios: one at 5 GHz and
one at 2.4 GHz. It includes an Ethernet wall switch with four 10/100/1000 ports, one of which may supply power.
Preparation
Run a data uplink cable (Cat5e/Cat6) for the 1 Gigabit uplink port.
Supply power—typically via IEEE 802.3af/at Power over Ethernet (PoE) on the same cable as the data uplink.
The total PoE uplink cable length must be no more than 100 m, including all cable segments. The Array must
be connected to PoGE networks without routing cables to the outside plant.
If you supply 802.3at PoE power to the uplink port, you may use the XR-320’s LAN4-PoE switch port to
supply 802.3af power and data to another device.
Alternatively, you may supply your own local 48 VDC power adapter meeting these specifications—
Pass-through port—this simply provides an Ethernet pass-through connection (with or without POE) from the
back of the unit to a port on the side of the XR-320.
LAN ports—these four switch ports on the bottom of the XR-320 allow you to provide Ethernet connectivity to
other devices. LAN4-PoE supplies 802.3af PoE, if a 48 VDC power adapter is used (Step 5 below), or if 802.3at
PoE power is supplied as described above.
Wall Installation
Figure 1
Locking
tab
XR-300 Series Access Points (APs) should be mounted on an inside wall.
1. Remove the blank wall plate from the wall with a screwdriver.
2. As shown in Figure 1, feed the Uplink (PoE) and Pass-through cables
through the opening in the supplied mounting bracket and secure the
bracket to the wall using the two screw holes previously occupied by
the blank wall plate. Ensure that the “UP” label is at the top, and that
the tab for the locking screw is on the left facing towards you.
Output Power +48VDC
Nominal Load
Current 0.63A
Ripple and Noise At 20Mhz, and output parallel with 0.1uF and
10uF capacitors to ground, temperature at 25°C,
at nominal input voltage
Connector Jack Plug 55*2.5*11.5mm
Polarity

XR300 Series Installation
2
3. Connect the cables as follows. Plug the Uplink-PoE and Pass-through cables into their respective sockets as
shown in Figure 2 (A). If the cables are not fitted with RJ45 jacks, they can be connected to the punch down
blocks using a dedicated network cable tool according to the sequence of colored wires marked on the back of
the AP, as shown in Figure 2 (B).
4. Move the AP into position against the bracket. Make sure that the locking tab mates with the locking slot as
indicated by the dotted line in Figure 2 (A). Secure the AP to the mounting bracket using the locking screw, as
shown in Figure 2 (C). The screw should be tightened to not more than 20Kgf and care should be taken not to
damage the equipment.
5. If you have not supplied power via PoE, use a local 48 VDC power adapter
(meeting the specifications on Page 1) as shown in Figure 3.
6. When the correct power is supplied, the POWER LED on the side of the unit
lights, and the XR-320 boots up.
Locking slot
Uplink PoE
Pass-through
Figure 2
AB
C
Install
Locking Screw
Locking tab
Figure 3

XR300 Series Installation
High Performance Wireless Networks
7ROO)UHHLQWKH86
6DOHV
)D[
&RUSRUDWH&HQWHU'ULYH
7KRXVDQG2DNV&$86$
7ROHDUQPRUHYLVLW
[LUUXVFRPRU
HPDLOLQIR#[LUUXVFRP
;LUUXV,QF$OO5LJKWV5HVHUYHG7KH;LUUXVORJRLVDUHJLVWHUHGWUDGHPDUNRI;LUUXV,QF
$OORWKHUWUDGHPDUNVDUHWKHSURSHUW\RIWKHLUUHVSHFWLYHRZQHUV&RQWHQWVXEMHFWWRFKDQJHZLWKRXWQRWLFH
812-0085-009 Rev B
Zero-Touch Provisioning and Management
XR-320 wireless APs are managed by XMS-Cloud as shown in this quick video guide: http://www.xirrus.com/
TV/Training/XMS-Cloud-Next-Generation. Your new APs appear in XMS even before you receive your
equipment. When the email arrives with your login information, use XMS-Cloud to specify the initial settings for
your APs. A Guided Tour will walk you through the basic steps of creating a profile containing configuration
settings, including creating SSIDs and firewall/application control rules. Once the installed AP has Internet
connectivity, it will automatically contact Xirrus for cloud-based zero-touch provisioning per your settings, install
the latest applicable license, and upgrade the AP to the latest software version as appropriate.
Manual Reset
If you need to manually reset the XR-320, the RESET button is located above the Pass-through port. Use a paper
clip to depress and hold the reset button (there should be a faint click). There are three actions that the XR-320 can
perform depending on how long the button is held down:
2 second hold time—LED test: all LEDs light for ten seconds.
4 second hold time—”Soft reset”: XR-320 reboots and uses the last saved configuration.
10 second hold time—Factory reset: XR-320 reboots and restores the factory default settings.