Xpelair Simply Silent SSWIN User manual

Simply SilentTM Contour Fan Window Kit
Installation and Maintenance Instructions
Model No. SSWIN (Cat No. 92996AA) Standard
Do read the entire instruction leaflet before commencing installation.
This window kit is designed to be used with Xpelair Simply Silent TM Contour Fans,
C4 series only and installed in a pre cut hole in a glazing unit.
Install fan in accordance with its installation instructions.
Do make sure the mains supply is switched off before attempting to make electrical
connections or carry out any maintenance or cleaning.
UK customers:
If you have any queries before or after installing this product call the Xpelair Technical
Hotline [phone].
Our engineers are there to help you during normal office hours.
Or you can fax at all other times on [phone].
Customers outside the UK should contact your local Xpelair distributor.
Please leave this leaflet with the fan for the benefit of the user.
Window Kit
Installed Fan
~Xpelair®

C4S/C4R - Operate the fan using an on/off switch (not supplied).
C4PS/C4PR - Operate the fan using an integral pull-cord.
C4TS/C4TR* - Built-in timer operates fan for a preset delay
from 30 seconds to 30 minutes.
C4HTS/C4HTR* - Operates when triggered automatically by the integral humidity
sensor, or by using an external on/off switch (not supplied).
In automatic mode: the built-in timer automatically operates the fan
for a pre-set delay time from 30 seconds to 30 minutes once humidity
drops below the pre-set Relative Humidity (RH) value.
External operation: When switched off using the external on/off switch
the fan continues to run for the preset delay from 30 seconds to 30
minutes.
* Factory settings: Timer 15 minutes, RH 75%
Kit must be installed with slots orientated downwards as shown.
Overall Dimensions (mm)
This window kit should only be installed by a competent person into a
suitable glazing unit with a pre prepared hole.
The competent person installing this kit should be aware of the dangers
associated with installing items in windows.
All Xpelair Simply SilentTM Contour AC fans have the following features:
Two speed extraction (Selectable at installation)
Built-in back draught shutter
[i]
0164
I 138
43
Maximum
Window
Thickness

Window Kit Component Parts
E
Minimum 30 seconds
Maximum 30 minutes
Installation
In a window glazing unit with a Ø115mm prepared hole at least 110mm in from the edges of
the glazing beads to the centre of the hole. With a maximum thickness of 43mm.
As far away as possible from and opposite to the main source of air replacement to ensure
airflow across the room (e.g. opposite the internal doorway).
Near the source of steam or odours.
Not where ambient temperatures are likely to exceed 50°C.
If installed in a kitchen, fans must not be mounted immediately above a cooker hob,
or eye level grill.
If installing in a room containing a fuel burning device which has a non-balanced flue, it is
the installer's responsibility to ensure that there is enough replacement air to prevent fumes
being drawn down the flue when the fan is operating up to maximum extract.
Refer to Building Regulations for specific requirements.
Exhaust air must not be discharged into a flue used for exhausting of fumes from appliances
supplied with energy other than electric. Requirements of all authorities concerned must be
observed for exhaust air discharge and intake flow rates.
Not suitable for use in possible chemical corrosive atmospheres.
What the installer will need.
No.1 or 2 Pozidrive screwdriver.
Method
Remove backing from gasket, insert window duct through hole and adhere window duct to
window. ENSURE slots in window duct face downwards as shown in diagrams.
Insert locator ring into window duct.
Insert the 4 pegs into the appropriate holes in the locator ring to ensure the minimum clearance
between peg and the outside surface of the window.
Gently tighten the 4 x M3 6mm long pan-head clamp screws to clamp the window kit in position.
(CAUTION over tightening may shatter the window).
Install fan in window kit in accordance with its installation instructions using the 3 x M4 8mm
long screws provided.
m
4 x M3 6mm LONG
PAN-HEAD SCREW
4xPEG~
f1
WINDOW
DUCT
LOCATOR
~
RING~
~

Guarantee.
UK only:
We, RXG Redring Xpelair, provide a guarantee against faulty parts and manufacture for a period of
2 years from the date of purchase. In the unlikely event of a product breakdown during the guarantee
period the product should be returned to the place of purchase or to RXG Redring Xpelair.
Exclusions:
This guarantee does not cover compensation for the loss of product or consequential loss of any kind
Damage or defects to the product arising from incorrect installation or lack of maintenance.
Transportation costs.
This guarantee does not affect your statutory rights
Technical advice and service
Customers outside UK - see international below.
United Kingdom
Xpelair have a comprehensive range of services including:
Free technical advice help-desk from Engineers on all aspects of ventilation.
Free design service, quotations and site surveys.
Service and maintenance contracts to suit all requirements.
Please ask for details:
By telephone on Techline: [phone]
By fax on Techfax: [phone]
At the address below
Head Office, UK Sales Office and Spares
RXG Redring Xpelair, Newcombe House, Newcombe Way, Orton Southgate, Peterborough, PE2 6SE, UK
Telephone: [phone] Sales/Spares Hotline: [phone]
Fax: [phone] Sales/Spares Faxline: [phone]
http:\\www.xpelair.co.uk
International.
Guarantee: Contact your local distributor or Xpelair direct for details.
Technical Advice and Service: Contact your local Xpelair distributor.
Cleaning (recommended once a month).
1. Before cleaning, isolate the fan completely from the mains supply.
2. Remove the front cover/baffle assembly by depressing the latch on the underside
of the cover and pulling off the front cover / baffle from the bottom.
3. To clean the front cover/baffle assembly, either wipe it with a damp, lint free cloth
or wash it with warm soapy water. Thoroughly dry the front cover and refit.
4. Do not immerse the fan in water or other liquids to clean any other parts of the fan.
5. Do not use strong detergents, solvents or chemical cleaners
6. Allow fan to dry thoroughly before use.
7. Apart from cleaning, no other maintenance is required.
Disposal
This product should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority for recycling advice.
Part No: 25587AB (Revision A)
~Xpelair ® 01 CE
() RXG
Redring Xpelair
FM02118 ISO 9001: 2000

Check out our full range of Bathroom Accessories
Bathroom Accessory Sets
Heated Towel Rails
Bathroom Extractor Fans
Bathroom Lighting
Shower Seats
Grab Rails
Shower Curtains
Toilet Brushes
Bathroom Cleaning Products
Wall Mounted Bathroom Accessories
Robe Hooks
Bathroom Tumblers
Toilet Roll Holders
Soap Dishes
Towel Rings
Shower Caddies
Bathroom Mirrors
Standard Bathroom Mirrors
LED Bathroom Mirrors
Shaving Mirrors