XtendLan DPC-IP100 User manual

i
Door Station User’s Manual
DPC-IP100

i
Table of Contents
1 Overview .................................................................................................................... 1
2 Basic Functions........................................................................................................... 2
2.1 Call Residents................................................................................................................. 2
2.1.1 Call Status .......................................................................................................... 2
2.1.2 Communication status....................................................................................... 2
2.2 Monitor Function........................................................................................................... 2
2.3 Unlock Function............................................................................................................. 2
2.3.1 Unlock During the Dial Process.......................................................................... 2
2.3.2 Unlock During the Communication ................................................................... 3
2.3.3 Unlock During the Monitor Status..................................................................... 3
2.3.4 Unlock via ID card (Optional)............................................................................. 3
2.4 Environment Light Compensation Function.................................................................. 3
2.5 External Alarm Function ................................................................................................ 3
3 Changing IP address ................................................................................................... 4
4 Config the ‘group call funtion’.................................................................................... 6
5 Specifications ........................................................................................................... 11
6 Device Port ............................................................................................................... 13
7 FAQ........................................................................................................................... 16

1
1Overview
Connect the device to the power, the system booted up properly. It goes to the standby
interface. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
XtendLan LOGO
2
Photosensitive
Component
It can detect the environment light. It is a
compensation light option.
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Button
Call button. Click it to generate a cal to
the indoor station. It has the blue

2
backlight.
5
Speaker
Audio output
6
Camera
It is to monitor the video of the door.
7
Microphone
Audio input
2Basic Functions
2.1 Call Residents
2.1.1 Call Status
In the standby status, press the call button. You can generate a call to the resident indoor
station. The indoor station bell rings.
2.1.2 Communication status
After you generated a call to the indoor station, if there is response, you can go to the
communication status. It can realize the dual-way video phone. It returns to the standby
interface after the dialogue ended.
2.2 Monitor Function
The indoor station can enable the monitor function of this device. You can open the
camera and monitor the device video.
2.3 Unlock Function
2.3.1 Unlock During the Dial Process
During the dial process, the indoor station can open the e-lock of the device remotely.
There is a 15-second for you to confirm the unlock operation. During these 15 seconds,
the video is properly displayed. After the 15 seconds countdown, system auto hangs up
and returns to the standby interface.

3
2.3.2 Unlock During the Communication
During the communication process, the indoor station can open the e-lock of the device
remotely. There is a 15-second for you to confirm the unlock operation. During these 15
seconds, the communication is OK and the video is properly displayed. After the 15
seconds countdown, the phone automatically hangs up.
2.3.3 Unlock During the Monitor Status
During the monitor status, the indoor station can open the e-lock of the device remotely.
There is a 15-second for you to confirm the unlock operation. During these 15 seconds,
the video is properly displayed.After the 15 seconds, the video automatically disappears.
2.3.4 Unlock via ID card (Optional)
The door is open after you passed the authentication ID card and passed the station
verification.
2.4 Environment Light Compensation Function
This device has the light compensation function when it is in the low illumination
environments or it is at night. It includes the button backlight and the camera
compensation light.
2.5 External Alarm Function
The device has 1-channel alarm input. They can be used for the door status and other
alarm detect.
It has 1-channel alarm output. There are two modes: NO/NC.

4
3Changing IP address
1..run ’cmd’
1).open
2.Input ‘telnet ’device IP(e.g.10.22.5.182)
Then press ’Enter’key
3.Username: root
Press ‘Enter’ key
Then input ifconfig

5
4. If want change the IP to 10.22.2.188
Can input: setenv –I ipaddr –c 10.22.2.188
5. The last step: Input ‘reboot’ or device is rebooted itself automatically.

6
4Config the ‘group call funtion’
1. cmd：telnet outdoor station IP 2000 username ：admin Password：admin

7
2、LAN Config: Group Call ：Enable (After choose ‘Enable’, restore the station )

8
After config, please click the ‘Save’

9
Add the room number:
Choose the ‘VTH Manage’,click the ‘Enter’
Get this interface:

10
Then can config the room number here.
After add the new monitor, press the ‘Esc’on the keyboard,choose the ‘save’

11
5Specifications
Model
DPC-IP100
OS
Main Processor
Embedded micro processor
OS
Embedded LINUX OS
Video
Video
Compression
Standard
H.264
Input/Approaching
induction
1/3-inch color CCD camera，540 TVL，0.1lux/F1.2
Night Vision
Support
Audio
Input
Microphone
Output
Built-in speaker
Bidirectional Talk
Support dual-way bidirectional talk
Operation Mode
Input
One button input(With backlight)
Card
Built-in ID card induction reader(Optional)
Alarm
Input
1-channel
Output
1-channel
Vandal proof
Support(Optional)
Locker Status
Detect
Support (Optional)
Network
Ethernet
10M/100Mbps Self-adaptive
Network Protocol
TCP/IP
Storage
Memory
128MB
Others
Power
DC 10~15V
Power
Consumption
Standby≤1W ；work≤10W
Working
Environments
-10℃~+55℃
＜10~90%RH
Dimensions
230mm*151mm*60mm（L*W*H）
Weight
0.96kg

12

13
6Device Port
The device rear panel is shown as in Figure 6-1.
1
2
3
4
Figure 6-1
Please refer to the following sheet for detailed information.
SN
Port Name
Function
1
Alarm port
Connect to alarm signal.
2
Network Port
Connect to the RJ45 port.
3
Power Port
Connect to 12V DC.
4
E-lock control port
Connect to cable

14
Figure 1
Door Lock Control
Door phone is designed to be able to control the door lock. Figure 1 is its rear panel
diagram.
The interface “12DC”is for the power supply interface; “RJ45”for network cable; “door
lock interface area”for electric lock. This user’s manual is based on electric lock. Figure 2
is the outward appearance of the electric lock.

15
Figure 2
Figure-3 is the connection diagram of the connection between door phone and electric
lock.
Figure 3
It is a transformer power supply, 220V AC is to be connected to L and N respectively
to transform and then output 12 DC in order to supply power for the door phone and
electric lock. The electric lock has four binding posts, two are power-supply binding posts,
and the other two are unlock binding posts. There are four terminals in the unlock interface
area of the door phone, namely, COM terminal, NC (electricity-on unlock), NO (electricity-off
unlock) and GND. Connect the L+ of the electric lock to the DC 12V positive pole; L- to the
NO; then the COM to DC 12V negative pole.
Note:
1. The power-supply cable RVV2*1.0 is adopted for the door phone and electric
lock both.
2. User can select either NC or NO to connect according to actual requirements.

16
7FAQ
Q：I can not boot up the device, or I can not see the light or hear the audio.
A：Please check your power cable connection and socket connection.
Q：I can not call.
A：Please check your network connection. Please make sure your station and
extension cable connection is OK.
Q：The prompt says the dial number does not exist. What shall I do?
A：Please check the dial number is OK or not.
Q：The system says the card is invalid. What shall I do?
A：The card status is abnormal. Please contact your administrator to check.
Q：The system says the card number is wrong. What shall I do?
A：It means current card does not authenticate. Please contact your
administrator to check.
Q：I have some problems, I am not so sure or I can not fix.
A：Please contact your local retailer for help.

17
Note:
This manual is for reference only. Slight difference may be found in user
interface.
All the designs and software here are subject to change without prior written
notice.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local service engineer for more
information.