XtendLan DPM-571 User manual

APARTMENT VIDEO INTERCOM SYSTEM
USER’S MANUAL
Features
■7 inch touch screen
■Up to 120 pcs colour picture memory
■15 chord tunes selectable
■Intercom function
DPM-571

1. Parts and Function
Bracket
Right View
Bottom View
TOP Vie
w
1
2
10
8
7
6
5
4
3
9
UNLOCK
INTERCOM
MON/ TALK
IN USE
1. TFT Touch Screen
2. Aluminum Panel
3. Microphone
4. UNLOCK Button
5. INTERCOM Button
6. TALK/MONITOR Button
7. LED for Power, In-use
8. Loudspeaker
9. Mounting Bracket Hold
10. Connection Port
WARNING
Don’t attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer servicing to qualified service personnel.
- 1 -

2. OPERATION INSTRUCTIONS
■ Operation for Basic Video Doorphone
1. When visitor inputs room numbers in
Door Station of the building or main
entrance, the Monitor rings, at the same
time, the screen displays the visitor image.
2. Then press icon(or MON/TALK Button),
and you can talk with the visitor for 60 seconds.
During talking state, press icon(or MON/
TALK Button) to end the conversation. If nobody
answers the phone, the screen will be turned off
automatically after 30 seconds. If the system connects two or more Monitors, when any
Monitor starts to talk, the other Monitors will be automatically shut off.
3. Press icon(or Unlock Button) to open the door
during call waiting or talking.
4. When Monitor is standby, press anywhere on the screen
and the screen will show the main menu, then press
icon (or press MON/TALK Button directly in the standby),
the screen will display the view of the Outdoor Station. During monitoring, press
icon(or MON/TALK Button), you can talk with outside through the Outdoor Station;
press the icon(or press MON/TALK Button again) to exit. However, monitoring
state is limited to 30 seconds and will be shut off automatically.
NOTE1: During the monitoring state, Press icon at bottom right, all the icons on the
screen will hide out, press anywhere on the screen again to display the icons.
NOTE2: During the monitoring state, press icon to record the current image.
- 2 -

■Image and volume adjust operation
1. During the monitoring, press icon on
the screen, the ADJUST MENU will be
displayed.
2. Press the item that you want to adjust, then
the selected item will be displayed in red color.
Press or icon to decrease or increase
the value of the current item. Any change will be save instantly.
3. Press EXIT item to quit out the setting.
NOTE1: Total 4 SCENE modes can be selected in sequence: NORMAL, USER, SOFT
and BRIGHT. Whenever you modify BRIGHTNESS or COLOUR, SCENE item
will be set to USER mode automatically.
NOTE2: The RATIO can be shifted from 16:9 to 4:3.
NOTE3: The BRIGHTNESS and COLOUR item is for the screen setting, adjust the value
that you are comfortable with.
NOTE4: The TALK VOLUME is for voice volume adjust.
■ Operation for Color Memo
The picture can be recorded both manually and automatically. The image capacity is
about 120 pcs, and the oldest one will be replaced if the memory is full.
1. Automatic Record
If AWAY SET mode is set (see as below) in the Monitor, when Door Station calls, a
picture will be automatically saved after 2 seconds. If nobody answers the call, the
Message LED will be lighten.
- 3 -

2. AWAY SET Mode
During standbby, touch anywhere on the
screen to launch the MAIN MENU, then
press icon,the SET UP menu will
show as bellow.
Press the AWAY SET item to turn it on,
then the IN-USED LED will flashing in
green; press again to turn it off.
3. Playback
During standby, touch the screen to launch MAIN
MENU, then press icon, the latest picture in
the Memory will be showed. Press icon or
- icon to view the next or previous picture.
During the playback, press icon will exit. If
no key was pressed within 40 seconds, the screen
will be closed.
4. Delete picture
During playback, press icon, a tip ‘DELETE?’ will be showed on the upper
right of the screen, press icon again to confirm, the current picture will be
deleted. You can press or icon to cancel if you don’t want to delete.
5. Date and time setting
Follow installation configuration instructions as below to set the clock.
■Operation for extended Outdoor Camera(If installed)
1. Visitor can call Monitor in Outdoor Camera, operations are similar as Door Station
calls. If only an extended doorbell without camera is connected, the Monitor will
ring only.
2. Door Camera can be used to survey if installed, by pressing TALK/MONITOR
Button one more time in monitoring state, the image will be switched to the Outdoor
Camera.
- 4 -

■Operation for Guard Unit related function
If Guard Unit is installed in the system, you can contact it by the operation as below.
1. When standby, press anywhere on the screen,
then press icon(or press INTERCOM
Button in standby), to activate the INTERCOM
FUNCTION MENU as shown on the at right.
2. Press CALL GUART UNIT item, a message
will be sent to Guard Unit, after the screen
displays CALL MESSAGE SEND OUT...,
you can turn off and wait Guard Unit to call
back. When receiving the call from Guard Unit, the Monitor will rings in a different
tune from other calls, and the screen may be in shut-off state (which depends on the
system configuration).
3. Press DIRECT DIAL GUARD UNIT item, it will directly dial to the Guard Unit,
then the screen will displays DIALING GUARD UNIT... PLEASE WAIT. If Guard
Unit answers the call, you can talk with the guard person. However, If the system is
busy, you have to try again later.
■Operation for Intercom
1. Intercom among Monitors can be started
by direct dialing the target room code.
2. When standby, press anywhere on the
screen, then press icon(or press
INTERCOM Button in standby), to activate
the INTERCOM FUNCTION MENU. Then
press the INTERCOM CALL item, you will
see a keypad on screen as right.
3. To call the room in the same building with you, just left the Building code to be
“000”, and directly input the Room code and then press [#] to dial; to call Monitor in
other buildings, you should input Building code after the Room code, then press [#]
to dial. During input state, press [*] to backspace and re-input number.
4. Note: Intercom will be available only when the system is free. Intercom function is
prior to monitor function, but calling function is always the first.
- 5-

■ Basic Setup instructions
1. During standby state, press anywhere on
the screen to display MAIN MENU, then
press icon to enter SETUP MENU.
2. The DOOR STATION and GUARD UNIT item
are for chord ring selection. You can select
different chord rings to identify different
calling source, press or icon to change
the chord ring, and the change will be saved
automatically.
3. The RING VOLUME item is for ring volume
adjust, press or icon to change the value.
4. The INSTALLATION…is for system
setting, when you press this item, a
password is asked. Input password
‘2008’, and press [#] icon to enter.
5. ROOM CODE item can only be configured
by the installer.
6. DATE AND TIME SET… item is
for clock setting, use the
touch screen keypad to input
numbers, and press “#” to save and
exit.
7. The INFORMATION… item is for the system information includes: the software
version, the hardware version and the producing date.
- 5 -- 6 -

3. Mount Illustration
1) Installation height of Monitor is usually from 145 to 160CM
2) Fix bracket on 86 Installation Box or wall surface directly, then install the Monitor.
4. Specifications
1) Power supply: DC 15~18V (by system Power Supply)
2) Power consumption: <0.5W in standby, <15W in working
3) Video signal: 1Vp-p, 75Ω, CCIR standard
4) Resolutions: 7 Inch TFT-LCD in 1440(H)*234(V)
5) Touch Screen: IPO film
6) Door Camera power: DC 10~12V (Supplied by Monitor)
7) Door Camera lens: 3.6mm, 72 degree horizontal visual angle
8) Monitor timing: 15 seconds
9) Talking timing: 60 seconds
10) Wirings: 6 wires with system, 4 wires with Door Camera
11) Ring tune: 15 chord tunes, user configurable
12) Color Memo capacity: 120 images
13) Dimensions：224(W)×153(H)×25(D)
14) Operating temperature: 0 ~ +40 centigrade
5. Precautions
1) All parts should be protected from violence vibration. And not allow be impacting,
knocking and dropping.
2) For clean the Lens& Screen, using hands or wet cloth is forbidden. Please do the
cleanness with soft cotton cloth, do not use the organic or chemical clean impregnate.
Image distortion may occur if the video door phone is mounted too close to magnetic
field e. g. Microwaves, TV, computer etc.
3) Please keep away the video door monitor from wet, high temperature, dust, and
caustic and oxidation gas in order to avoid any unpredictable damage.
- 7 -