XtendLan DPC-D218ID User manual

DPC-D218ID
D oor Station
User Manual
RF CARD
1 2 3
4 5 6
7 8 9
* 0
#

1.Parts and Functions
350
EB+ EB- N.O LK+
LK-
+12V
Camera Lens
Night View LED
Speaker
LCD Screen
Adjustable Camera
ID Card Window
RF CARD
1 2 3
3 2 1 Connectiong Port
Digital Keypad
4 5 6
7 8 9
Microphone
*
0 #
128 mm
With rainy cover
2. Terminal Descriptions
SD Card Slot L1
L2
CN-LK
T/R -T/R+
3 2 1
Bus
RF CARD
3 2 1
J/KMB JP-LK
1 2 3
4 5 6
7 8 9
*
0 #
• +12V: 12VDC power output.
• LK-(GND): power ground.
• LK+(COM): common contact of the Relay .
• NO.:normally open contact of the Relay(refer to 2-wire technical guide for Lock
connection detail information).
• EB+: Exit button connection port.
• EB-: Exit button connection port.
• JP-LK: For electronic lock safety type setting(refer to Door Station Lock Connections).
• T/R-: USB-RS485 communication terminal negative.
• T/R+: USB-RS485 communication terminal positive.
• Bus(L1,L2): non-polarity bus line.

3.Door Station Mounting
1
Drill a hole and attach the
rainy cover to it
2
The view for rainy
cover after mounted
3
Camera
angle
Adjust the camera angle and attach the
metal to the panel and wire correctly.
4
Attach screws to fix the
metal box
5
Attach the unit to the rainy
cover correctly
6
Attach the baffle to protect
the unit from dropping
7
The last view for all mounting

4. Door Lock Connections
1. Internal Power Supply Mode
Use the power of the system to supply for the electronic lock, so that the lock can be
connected to the door station directly, without an additional power supply for the electronic lock.
Note that the door station can only output 12Vdc power, therefore the kind of lock is limited.
• The rated power of the lock must be less than 12Vdc 300mA when using internal power
supply mode
• The GND must connect to the negative of the lock, and the COM connect to the positive .
• Jumper set to 1-2 position for Power-to-Unlock safety type(Normally open mode); set
to 2-3 position for Power-off-to -Unlock type(Normally closed mode).Note that the
unlock relay mode is set on the Parameter tab of DT CONFIG software.
• If different unlocking time is needed to be configured, the DT CONFIG software can be
used to change the Unlock Timing on the Parameter tab(see the program section).
A. Connection for Power-to-Unlock type:
-
+
12V 300mA
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
set to Normally open on the
Unlock Relay mode on DT-config
software.
Jumper set to 1-2 position
JP_LK
B. Connection for Power--off-to-Unlock type:
-
+
12V 300mA
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
set to Normally Closed on the
Unlock Relay mode on DT-config
software.
Jumper set to 2-3 position
JP_LK

3 2 1
-
2. External Power Supply Mode
When the electronic lock is over 12 Vdc, additional power supply for the lock is needed.
• The power supply for the lock must be less than 48Vdc 1.5A.
• The Jumper must be removed when using external power supply. The default setting is
Power-to-Unlock type(Normally open mode), if use Power-off-to-Unlock type, change
the Unlock Relay mode to Normally closed mode .Note that the unlock relay mode is
set on the Parameter tab of DT CONFIG software.
• If different unlocking time is needed to be configured, please use the DT CONFIG
software to change the setting on the Parameter tab(see the program section).
C. Connection for Power-to-Unlock type:
+
-
+12V
+ LK -
(GND)
LK+(COM)
-
N.O.
EB+
EB -
set to Normally Open on the
Unlock Relay mode on DT-config
software.(default)
Note: Cut off this line when
Remove the Jumper
JP_LK
using external power supply
D. Connection for Power--off-to-Unlock type:
+
-
+12V
+ LK - (GND)
LK+(COM)
N.O.
EB+
EB -
set to Normally Closed on the
Unlock Relay mode on DT-config
software.
Note: Cut off this line when
Remove the Jumper
JP_LK
using external power supply

5. Door Station Configurations
1. About room code(address):
Room Code(also called room address) is a code assigned to each monitor, to identify different
monitors; each monitor have a unique room code in one buidling.The room Code is stored in
each Monitor’s inner EEPROM memory, and does not lose even the monitor is power off.
2. About Debug State:
The Debug State is your starting point for using all the applications on DPC-D218.
> > D e b u g S t a t e < <
0 - # R e d i a l
RF CA R D
1 2 3
1 - # To o l s
4 5 6
7 8 9
*
0 #
[ 9 0 0 8 ]
2 - # E x i t s
Please Input Password
When Door Station is in
standby, press '#' key
input '9008', then input the
Admin Code.(66666666 by
default)
Debug State menu is launched
Press "2#" key to exit out the debug state.
3. About Debug Tools:
During working at Debug State, press "1#" to enter tools page, Debug Tools overviews is
shown as below:
> > D e b u g S t a t e <
<
0 - #
R e d i a l
1 - # To o l s
2 - # E x i t s
Tools
Pres NO.
to select
*Back
1 . I n s t a l l e r S e t u p
2 . S e t u p
3 . C a r d M e m o r y
4 . O n l i n e M o n i t o r s
5 . O n l i n e D e v i c e s
6 . V o l t a g e M e a s u r e

Table 1:
Item
Submenu
1. Installer Setup
1. ID Code [1]
2. Unlock Timing [05]
3. Unlock Output [0]
4. Card Memory [0]
5. Doorplate Mode
6. Audio Options ...
7. Parameters ...
8. Installer Code ...
9. Default ...
2. Setup
1. Language [1]
2. Tone Select [03]
3. Tone Volume [08]
4. Unlock Code [1111]
5. Display Mode
6. Clock ...
7. Setup Code ...
8. About ...
9. Default ...
3. Card Manage
1. Add Card ...
2. Delete By Card
3. Delete By M.code
4. Cards Information
5. Format
4. Online Monitors
To search the online monitors,input the monitor code
number to search
5. Online Devices
To search the online door stations.Max.4 door station
can be searched
6. Voltage Measure
To check the voltage of the monitor,note that the
monitor must be online.

Basic Tools Detail:
Table 2(Installer Setup):
Item
Description
Factory
set
ID Code
If only one door station is installed in this building, set
to 1;
If multi door stations are installed, primary door station
must be set to 1, and other slave door stations must
be set from 2 to 4. Note that max. 4 door stations is
available in one building
[1]
Single
Unlock Timing
To set the time that how long the door keeps open
when door is released. Range from 01 to 99 seconds.
[05]
5 seconds
Unlock Output
To set the unlock mode to match the corresponding
lock.Rand from 0 to 1
0
Card Manage
To set the card location.If set to 0,the card is saved in
door station.If set to 1, the card is saved in DPA-D2-IPC
0
Doorplate Mode
To set the calling mode.If set to 0,it's the auto
mode,that means the calling will be activated directly
after inputting 2 digits code.If set to 1,it's the manual
mode,that means you should press "#" button to
activate the calling after inputting the code.
[0]
Auto mode
Audio Options ...
To set the talking mode.If set to 0,hands free mode is
activated.If set to 1,handset mode is activated.
0
Parameters ...
To show the parameters,please refer to table 2.1
Installer Code ...
To change door station administrator code
[66666666]
Default ...
Note this operation is irreversible. Once restore is
activated, all parameters will return to factory default
setting except the information of access card.

Table 2.1(Parameters):
Item
Description
Factory
set
Monitor Timing
To show the monitor time,Range from 6s to 600s
30s
Switch Timing
To show the surveillance time for each Door Station or
CCTV camera.Range from 6s to 600s
40s
Wait Timing
To show the calling wait time,Rang from 10s to 600s
30s
Talk Timing
To show the limitation time of talking,Range from 10s
to 600s
90s
Monitor & Speack
To enable Indoor Monitor under monitoring state can
speak to Door Station at same time. If set to 1, talk
enabled; set to 0, disabled.
Monitor & Unlock
To enable Monitors under monitoring state can open
the door at the same time.If set to 0, unlock function
is disabled; Set to 1, unlock is enable;Set to 2,unlock
is enable and close at once;Set to 3,unlock is enable
and close in 5s.
[1]
Ring Numbers
To show ring times when door station calls monitor.4
options for choice. If set to 0, ring once. If set to 1,ring
twice. If set to 2, ring three times.If set to 3,cycle ring
[1]
NameList Display
Mode
To show the namelist display mode.If set to 0,it's the
DT-Config display mode.If set to 1,it's the Simulate
display mode
[0]
Working Mode
To show the working mode.If set to 0,it's the apartment
system mode.If set to 1,it's the villa mode.
[0]
Note: this section is set on DT-Config software, for more detail informations, please refer to the
DT-Config software user instructions.

Table 3(Setup):
Item
Description
Factory
set
Language
To change language.the code format is 4 digits.Please refer
to part 5,section 10(change door station language) for more
detail informations.
01
Tone Select
Select the chime of Door Station in calling wait state, 12
chord tunes are available, key in 01 to 12 to select.
03
Tone Volume
Adjust the tone volume for dooor station in calling.Rang from
01~15
08
Unlock Code
To change unlock code in Common Code Unlock mode, in
4-digits format. 1111 is the default unlock code.
[1111]
Display Mode
To select the Door Station screen menu .If set to 0,the
screen displays the visitor's image when talking.If set to 1,the
screen displays icons when talking.
[0]
Clock ...
To set date and time.
Date format:if set to 0,date format is DD/MM/YY,if set to
1,date format is MM/DD/YY.
Time format: if set to 0,time format is 24 hour standard.If set
to 1,time format is12 hour standard.
Setup Code
To change the Program Code.
[88888888]
About ...
1. Hardware version---To show the Door Station(including
ACS) hardware information
2. Software version ---To show the Door Station(including
ACS) software information
3. Manufacture Date---To show the manufacturing date
4. Dialing Counts---To show the call operation counts
5. Calls Counts---To show the established calling counts
6. Unlock Counts---To show the unlock operation counts
7. Standby Voltage---To show the voltage that the door
station in standby.
8. Working Voltage---To show the voltage that the door
station in working.
9. Video Standard---PAL or NTSC standard
10. UI_CODE---To show the UI byte counts and check box
11. MCM-VER---To show the version and language for MCM
12. Updated---To show the updated time for UI
Default ...
Restore all Setup parameters to factory default setting,Please
note that this operation is an irreversible