XtendLan DPC-518ID User manual

User Manual
Door Station
Please read this manual carefully before using the product you purchase, and keep it well for future
use.We reserve the right to modify the specication in this manual at any time without notice.
1 2 3
654
7 8 9
#0
*
RF CARD
DPC-518ID

Contents
1. Parts and Functions..................................1
2. Terminal Descriptions ...............................1
3. Door Station Mounting..............................2
4. Basic System Connection ..........................3
5. Door Lock Connections .............................4
6. Door Station Congurations ......................6
7. Language and UI updating .......................11
8. Specication ..........................................12

1.Parts and Functions
2. Terminal Descriptions
Camera Lens
Night View LED
Speaker
Adjustable Camera
Connectiong Port
With rainy cover
350 mm
128 mm
1 2 3
654
7 8 9
#0
*
RF CARD
LCD Screen
ID Card Window
Digital Keypad
Microphone
12
3
T/R -
CN-LK
T/R+
J/KMB JP-LK
RS-485
P - P+
JWP
JWB(OUT)
SD Card Slot
EB+ EB- N.O LK+ LK-
+12V
12
3
12
3
• +12V:12VDCpoweroutput.
• LK-(GND):Powerground.
• LK+(COM):CommoncontactoftheRelay.
• NO.:NormallyopencontactoftheRelay(Canbesettobenormallyclosed)
• EB+:Exitbuttonconnectionport.(ShortEB+&EB-tounlock)
• EB-:Exitbuttonconnectionport.
• JP-LK:Forelectroniclocksafetytypesetting(refertoDoorStationLockConnections).
• T/R-:USB-RS485communicationterminalnegative.
• T/R+: USB-RS485communicationterminalpositive.
• JWP(P+,P-): Powerinputfordoorstation
• JWB(OUT): BUSOutput(IncludingData,audioandvideosignal)
• SD Card Slot: forupdatingthelanguageandUIofdoorstation -1-

3.Door Station Mounting
1 2 3
4
7
5 6
Drill a hole and attach the
rainy cover to it
Attach screws to fix the
metal box
Attach the unit to the rainy
cover correctlly
Attach the baffle to protect
the unit from droping
The last view for all mounting
The view for rainy
cover after mounted
Adjust the camera angle and attach the
metal to the panel and wire correctly.
Camera
angle
4
2mm
147mm
395mm
-2-

4. Basic System Connection
Thebasicsystemconsistsof:Doorstation,Distributor,Monitor,Powersupplyandlock.
-3-
C5-F4
C5-F4
Connect to next C5-F4
T/R -
CN-LK
T/R+
J/KMB JP-LK
EB+ EB- N.O LK+ LK-
+12V
12
3
12 V DC lock
- +
PS5
1 2 3
654
7 8 9
#0
*
RF CARD
85~260AC
PS5
P+ P-

5. Door Lock Connections
JP_LK
12V 300mA
Jumper set to 1-2 position
+
-+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
1 2 3
set to Normally open on the
Unlock Relay mode
12V 300mA
Jumper set to 2-3 position
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
+
-
set to Normally Closed on the
Unlock Relay mode
JP_LK
1 2 3
-4-
1. Internal Power Supply Mode
Usetheinternalpowertosupplyfortheelectroniclock,sothatthelockcanbeconnected
tothedoorstationdirectly.Notethatthedoorstationcanonlyoutput12Vdcpower,Anyhigh-
powerlockshoulduseexternalpowerconnectionoritmightcausedamagetothedoorstation.
• Theratedpowerofthelockmustbelessthan12Vdc300mAwhenusinginternalpower
supplymode
• TheGNDmustconnecttothenegativeofthelock,andtheCOMconnecttothepositive.
• Jumpersetto1-2positionforPower-on-to-Unlocksafetytype(Normally open mode);
setto2-3positionforPower-off-to-Unlocktype(Normally closed mode).
• Ifdifferentunlockingtimeisneededtobeconfigured,changetheUnlock Timingon
doorstation.
A. Connection for Power-on-to-Unlock type:
B. Connection for Power--off-to-Unlock type:

+
+
-
-
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
Remove the Jumper
set to Normally Open on the
Unlock Relay mode (default)
JP_LK
1 2 3
Note: Cut off this line when
using external power supply
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
Remove the Jumper
set to Normally Closed on the
Unlock Relay mode
+
+
-
-
JP_LK
1 2 3
Note: Cut off this line when
using external power supply
-5-
2. External Power Supply Mode
Whentheelectroniclockisover12Vdc,additionalpowersupplyforthelockisneeded.
• Thepowersupplyforthelockmustbelessthan48Vdc1.5A.
• TheJumpermustberemovedwhenusingexternalpowersupply.Thedefaultsettingis
Power-on-to-Unlocktype(Normally open mode),ifusePower-off-to-Unlocktype,
changetheUnlockRelaymodetoNormally closed mode.
• Ifdifferentunlockingtimeisneededtobecongured,changetheUnlock Timingon
doorstation.
C. Connection for Power-to-Unlock type:
D. Connection for Power--off-to-Unlock type:

6. Door Station Congurations
About Debug State:
TheDebugStateisyourstartingpointforusingalltheapplications.Toopenthedebug
state,pleaserefertothefollowingsteps:
WhenDoorStationisin
standby,press'#'key
Press"2#"keytoexitoutthedebugstate.
Input'9008',theninputthe
AdminCode.(66666666by
default)
DebugStatemenuislaunched
[ 9 0 0 8 ]
Please Input Password
1 2 3
654
7 8 9
#0
*
RF CARD
>> Debug State <<
1 - # To o l s
0 - # R e d i a l
2 - # E x i t s
About Debug Tools:
DuringworkingatDebugState,press"1#"toentertoolspage,DebugToolsoverviewisshown
asbelow:
1. Installer Setup
2. Setup
3. Card Memory
4. Online Monitors
5. Online Devices
6. Voltage Measure
Pres NO.
to select
*Back
Tools
>> Debug State <<
0 - # R e d i a l
2 - # E x i t s
1 - # To o l s
-6-

Item Submenu
1. Installer Setup
1.IDCode[0]
2.UnlockTiming[05]
3.UnlockOutput[0]
4.CardMemory[0]
5.DoorplateMode
6.AudioOptions...
7.Parameters...
8.InstallerCode...
9.Default...
2. Setup
1.Language[1]
2.ToneSelect[03]
3.ToneVolume[08]
4.UnlockCode[1111]
5.DisplayMode
6.Clock...
7.SetupCode...
8.About...
9.Default...
3. Card Manage
1.AddCard...
2.DeleteByCard
3.DeleteByM.code
4.CardsInformation
5.Format
4. Online Monitors
Tosearchtheonlinemonitors,inputthestarting
numberandendingnumber,thedoorstation
Willsearchallthemonitorsinbetweenonebyone
Table1:Menuoverview
-7-

Basic Tools Detail:
Item Description Factory
set
IDCode
1.WhenthereisonlyonedoorstationandnoC5-IPC,
setto0.Andsetthetypeofdistributorusedwithit.
WhenC5-IPCisconnected,mustnotbesetto0.
2.WhenC5-MDSisconnected,besettofrom1~8
accordingtowhichportitisconnectedontheC5-MDS
3.Whenusedascommondoorstation,setto9
[0-11]
Standalone
Usedwith
C5-F4
UnlockTiming Tosetthetimethathowlongthedoorkeepsopen
whendoorisreleased.Rangefrom01to99seconds.
[05]
5seconds
UnlockOutput
Tosettheunlockmodetomatchthecorresponding
lock.Rangefrom0to1.
0:Power-on-to-UnlockMode(NormallyOpenMode)
1:Power-off-to-UnlockMode(NormallyClosedMode)
0
CardMemory
Tochoosetousethememoryofdoorstationorthatof
C5-IPCwhenaccesscardsareinuse
0-UsememoryofDSforaccess
1-UseC5-IPCforaccess
0
DoorplateMode
Tochoosetheinputmodewhenyoucallmonitor.It
canbesettofrom1to8digits.totally8numbersor8
lettersormixedareavailable
4digits
AudioOptions...
Tosettheaudiomatchifthereisaudioproblem
causedbybadmatch.
1.audiomatchbetweendoorstationandmonitor
2.audiomatchbetweendoorstationandguardunit
0
Parameters... Toshowtheparameters,pleaserefertotable2.1
InstallerCode... Tochangedoorstationadministratorcode [66666666]
Default...
Toretrievetheoriginalconfigurationofdoorstation.
Notethisoperationisanirreversibleoperation.Once
restoreisdone,theparametersincludingInstaller
CodeandSetupCodewillreturntofactorydefault
Table2(InstallerSetup):
-8 -