XtendLan TESTPTZ705ADHS User manual

TESTPTZ705ADHS
IP camera tester
User Manual

Content
1 .Safety information -----------------------------------------------------------------------------------------------------1
2. IP Camera Tester Introduction---------------------------------------------------------------------------------------1
2.1 General -----------------------------------------------------------------------------------------------------------1
2.2 Features-----------------------------------------------------------------------------------------------------------2
2.3 Function----------------------------------------------------------------------------------------------------------5
2.4 Packing list ---------------------------------------------------------------------------------------------------- 12
2.5 Function interface -------------------------------------------------------------------------------------------- 13
3. Operation -------------------------------------------------------------------------------------------------------------- 16
3.1 Installing the Battery----------------------------------------------------------------------------------------- 16
3.2 Instrument connection --------------------------------------------------------------------------------------- 17
3.2.1 IP camera connection-------------------------------------------------------------------------------------- 17
3.2.2 Analog camera connection ------------------------------------------------------------------------------- 18
3.2.3 HD Coaxial camera connection ------------------------------------------------------------------------- 18
3.2.4 HDMI IN ---------------------------------------------------------------------------------------------------- 19
3.3 OSD menu ----------------------------------------------------------------------------------------------------------- 19
3.3.1 Lite mode& Normal mode ------------------------------------------------------------------------- 20
3.3.2 Drop-down Menu------------------------------------------------------------------------------------ 23
3.3.3 Short cut-menu --------------------------------------------------------------------------------------- 24
3.3.4 Screen capture---------------------------------------------------------------------------------------- 25
3.3.5 TesterPlay --------------------------------------------------------------------------------------------- 26
3.3.6 Rapid video ------------------------------------------------------------------------------------------- 27
3.3.7 IP discovery------------------------------------------------------------------------------------------- 28
3.3.8 Rapid ONVIF test------------------------------------------------------------------------------------ 29
3.3.9 IP camera test----------------------------------------------------------------------------------------- 44
3.3.10 HDMI IN--------------------------------------------------------------------------------------------- 46
3.3.11 Video monitor test---------------------------------------------------------------------------------- 50
3.3.12 Color-bar generator (TV OUT)------------------------------------------------------------------ 59

3.3.13 CVI camera test------------------------------------------------------------------------------------- 61
3.3.14 TVI camera test------------------------------------------------------------------------------------- 68
3.3.15 AHD camera test ----------------------------------------------------------------------------------- 70
3.3.16 Network tool ---------------------------------------------------------------------------------------- 71
（1）IP address scan -------------------------------------------------------------------------------------- 71
（2）PING Test -------------------------------------------------------------------------------------------- 72
（3）Network test (Ethernet bandwidth test) --------------------------------------------------------- 72
（4）Port Flashing----------------------------------------------------------------------------------------- 76
（5）DHCP server----------------------------------------------------------------------------------------- 77
（6）Trace route ------------------------------------------------------------------------------------------- 77
（7）Link monitor ----------------------------------------------------------------------------------------- 78
3.3.17 Rapid IP Discovery -------------------------------------------------------------------------------- 79
3.3.18 PoE power / DC12V 2A and DC 5V 2A USB power output------------------------------- 80
3.3.19 Cable Test ------------------------------------------------------------------------------------------ 81
3.3.20 RJ45 cable TDR test------------------------------------------------------------------------------- 82
3.3.21 PoE Voltage test------------------------------------------------------------------------------------ 85
3.3.22 12V power input test------------------------------------------------------------------------------- 86
3.3.23 Audio Record --------------------------------------------------------------------------------------- 86
3.3.24 Data monitor ---------------------------------------------------------------------------------------- 87
3.3.25 Audio player----------------------------------------------------------------------------------------- 87
3.3.26 Media Player ---------------------------------------------------------------------------------------- 88
3.3.27 RTSP Player----------------------------------------------------------------------------------------- 88
3.3.28 Hik test tool------------------------------------------------------------------------------------------ 90
3.3.29 Dahua test tool-------------------------------------------------------------------------------------- 92
3.3.30 Update------------------------------------------------------------------------------------------------ 96
3.3.31 Office-------------------------------------------------------------------------------------------------97
3.3.32 LED Flashlight-------------------------------------------------------------------------------------- 97
3.3.33 Browser ---------------------------------------------------------------------------------------------- 98
3.3.34 Notepad:---------------------------------------------------------------------------------------------- 98

3.3.35 System Setting -------------------------------------------------------------------------------------- 99
3.3.36 File explorer----------------------------------------------------------------------------------------104
3.3.37 Theme -----------------------------------------------------------------------------------------------105
3. 4 Audio test ----------------------------------------------------------------------------------------------------108
3.5 HDMI output-------------------------------------------------------------------------------------------------108
3.6 PoE power output--------------------------------------------------------------------------------------------108
3.7 DC12V 2A power output ----------------------------------------------------------------------------------109
4. Specifications --------------------------------------------------------------------------------------------------------111

Page.1.
1 .Safety information
◆The tester is intended to use in compliance with the local rules of the electrical usage and avoid to
apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc.
◆To prevent the functional decline or failure, the product should not be sprinkled or damped.
◆The exposed part of the tester should not be touched by the dust and liquid.
◆During transportation and use, it is highly recommended to avoid the violent collision and vibration
of the tester, lest damaging components and causing failure.
◆Don’t leave the tester alone while charging and recharging. If the battery is found severely hot, the
tester should be powered off from the electric source at once. The tester should not be charged over 8
hours.
◆ Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately and
move away other connected cables.
◆The tester should not be used in the environment with the flammable gas.
◆Do not disassemble the instrument since no component inside can be repaired by the user. If the
disassembly is necessary indeed, please contact with the technician of our company.
◆The instrument should not be used under the environment with strong electromagnetic interference.
◆ Don’t touch the tester with wet hands or waterish things.
◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to remove,
the soft cloth with water or neutral detergent can be used. But the cloth should be tweaked
sufficiently.
2. IP Camera Tester Introduction
2.1 General
The 7 inch touch screen IP camera monitor is designed for maintenance and installation of IP cameras,
analog cameras, TVI, CVI AHD, cameras, as well as testing 4K H.264 /4k H.265 camera via
mainstream, The 1280x800 resolution enables it to display network HD cameras and analog cameras in
high resolution. The unit supports many ONVIF PTZ and analog PTZ control. The combination of

Page.2.
touch screen and key buttons make the IP camera tester very user- friendly.
The tester is also a great tool for Ethernet network testing. It can test PoE power voltage, PING, and IP
address searching. You can use the blue cable tracer to locate individual connected cables from a bundle
of cables. Test LAN cable for proper connection termination. Other functions include providing 24W
PoE power to your camera, HDMI IN and out, CVBS loop test , testing IP and analog at the same time,
LED Flashlight, DC 12V 2A power output and much more. Its portability, user-friendly design and
many other functions make the IP tester an essential tool for all installers or technicians.
2.2 Features
New 7 inch IPS touch screen cctv tester,1280*800 resolution.
H.265&H.264, 4K display via mainstream.
IP and analog testing at the same time.
In HDMI IN mode, It can converter test from analog to digital with dual test window IP &
HDMI IN or Analog & HDMI IN
RJ45 cable TDR test and cable quality test, to test cable pair status, length, attenuation
reflectivity, impedance, skew and other parameter.
Screen capture, long press the key “enter”, can capture screen interface and save it in any time
12V power input test
“TesterPlay” app, support Tester, PC and mobile phone display at the same time. The android
version mobile phone install “TesterPlay ” app, or install VLC player in the PC, can real-time
receiving screen information from the tester Screen management, change function’s icons order,
create new directory.
Themes: Lite mode and normal mode can select , change the icons and desktop.
background ,change sliding effect etc.

Page.3.
Built in Wi-Fi ,display image from the wireless camera , create WIFI hotspot.
Rapid video, auto scan the IP camera address, via one key to view the image.
Screen lock : password lock and pattern lock are optional.
Office, quick office app (support excel, word, ppt format) doc. Editable.
Rapid IP scan , auto scan whole network or other network device ‘s IP address.
CVBS loop test , tester can receive and send the color bar generator ,to check BNC cable.
Traffic monitoring of the tester "Lan port", display network port or WIFI connection
real-time .upload and download speeds and other network parameters.
Shortcut button, drop-down menu ,PoE power switch ,IP setting, WLAN switch , HDMI IN
functions,screen lock, password lock screen or pattern lock etc.
IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan
the whole network segment IP, and auto-modify tester’s IP address.
Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate
Hikvision camera.
Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify
unactivated hikvision camera, also can display image from the Hikvision camera.
DH test tool app is design for Dahua Camera test, and modify IP, user name and password parameters etc.
ONVIF camera test, support 4K.
It is used unique hardware decoding, display image from the 4K camera via mainstream.
You can select sub-stream to test higher resolution camera.
ONVIF IP camera video testing.
Compatible with H.265/H.264/MPEG4/MJPEG IP cameras, such as Dahua, HIKVISION, and
ACTI Customized service are available.
Built in Wi-Fi, can receive image from wireless camera, as well as ONVIF and customized IP
cameras.
HD CVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call
camera OSD menu

Page.4.
HD TVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call
camera OSD menu
AHD camera image display, zoom, video record and playback, Coaxial PTZ control and call
camera OSD menu
HDMI signal output, supports up to 1080P.
Analog camera image display, auto adapt and display the video format of NTSC/PAL.
Support more than 30 protocols, such as PELCO-P,PELCO-D,SAMSUNG etc.
Video image digital zoom to view the image in greater detail.
Snapshot function allows you to save the current image as a JPG file in the SD card.
Built in enhanced image generator, send the color, pure blue and black image, test monitor
transmission channel and debug display device, observe whether there are light spots or black
spots on the monitor.
LED Flashlight.
8GB Micro SD card included.
LCD screen brightness/contrast/color Saturation adjustable.
Enhanced Color bar generator, PAL/NTSC multi-system color bar video generator (Eight-system
switchable, transmit/receive eight-system colorful images).
Ping test, PING is the most conventional network debugging tools; it is used for testing if the
connected IP camera or other network equipment’s Ethernet port is working normally and the IP
address is correct.
In digital IP surveillance applications, if the IP camera’s IP address is not known, the device
cannot be used. An IP address scan can quickly search for the connected IP camera or other
network device’s IP address.
The PoE voltage test can test for PoE voltage when a POE switch is supplying POE power to IP
camera.
Cable test , Test LAN cable or telephone cable,UTP cable etc ,cable type and the sequence of
wires will be displayed.
Support RS485,rate 600 ～115200bps adjustable.

Page.5.
PTZ protocol analysis, control protocol command displays to check RS485 transmission
whether is normal, easy to find the fault device.
PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and
sets and the preset position.
DC5V 2A power output for USB charging (No USB data exchange, voltage only)
PoE power output, supply temporary power for PoE camera.
DC5V 2A power output, as a power bank.
Audio input and output, test and output the audio signal.
7.4V Lithium Ion Polymer Battery ,Working time lasts 10 hours, after charging for 6 ~7 hours.
2.3 Function
H.265 mainstream test
With the new hardware decoding, display the image from the 4 K H. 265 camera.
IPS display and touch screen operation
7 inch IPS touch screen cctv tester , 1280*800 resolution.
Intelligent interface
You can select “Lite mode or “Normal mode”. In normal mode, self-define desktop, press functions
icons to enter screen management status. You can move the icon to any pages; self-define the number of
icons in any page,Make interface sample and individuality.
HDMI HD digital signal input
HDMI digital input , support resolution 720×480p /720×576p /1280×720p /1920×1080p
/1024×768p/1280×1024p /1280×900p /1440×900p. Digital video recorder and other devices can display
images of the tester through the HDMI input.

Page.6.
RJ45 cable TDR test
RJ45 cable TDR test and cable quality test, to test cable pair status, length, attenuation reflectivity,
impedance, skew and other parameter.
Screen capture
Screen capture, long press the key “enter”, can capture screen interface and save it in any time
12V power input test
show the current adaptor input voltage and power.
TesterPlay
“TesterPlay” app, support Tester, PC and mobile phone display at the same time. The android version
mobile phone install “TesterPlay ” app, or install VLC player in the PC, can real-time receiving screen
information from the tester
It can converter test from analog to digital with dual test window IP & CVBS.
Dual test window ,IP & HDMI IN or Analog & HDMI IN.
Theme
Set function apps background, you can select 4 different colors at the same time. Set the desktop and
application interface background, you can choose pure colors or custom pictures. You also can change
RGB to set color. When you choose sliding effect, "three-dimensional, folding, left and right folding,
rotation, ombre effect" are optional.
Rapid video
Auto scans whole network IP address, by one key to detect all network cameras and auto display the
images.
Wireless WIFI
Built in Wi-Fi, can receive WIFI network camera images (ONVIF or customized camera) or network

Page.7.
data, etc. create Wi-Fi hotspot.
Screen lock
You can choose password Lock screen, pattern Lock screen or “NO”.
Office Software
Built in Quick office app ,can edit the documents, spreadsheets, and presentations etc.
Speed IP exploration
Search IP address of the connected IP camera or other network equipments in whole network segment.
Traffic monitoring
Traffic monitoring of the tester "LAN port", display network port or WIFI connection real-time upload
and download speeds and other network parameters.
Drop-down menu
Press and slide at right top right corner twice to open shortcut menu. The shortcut menu includes POE
power output, IP settings, Wi-Fi, HDMI IN, CVBS, Video OUT, LAN, Brightness, settings etc.
CVBS loop test
“TV out” testing app, it can send and receive color bar generator through the tester’s video out and
video in”.
IP discovery
IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan the
whole network segment IP, and auto-modify tester’s IP address.
Rapid ONVIF
Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate
Hikvision camera.
Hik test tool

Page.8.
Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify unactivated
hikvision camera, also can display image from the Hikvision camera.
DH test tool
DH test tool app is design for Dahua Camera image test, modify IP, user name and password
parameters etc.
IP camera test
The device is designed for ONVIF IP camera testing. It can display the image from an IP camera and
change the IP address.
The 7 inch 1280x800 screen display allows the user to view the image with a sufficient screen size.
With the ONVIF tool, you can display the image from an IP camera and use the PTZ functions.
Currently the IP camera tester supports more than 80 brands IP cameras, such as ACTi, Dahua,
Hikvision, Samsung, Honeywell and many more.
OEM service is available. Users can send us the IP camera for our engineers try to add the protocols to
the tester, or send us the mobile apps (Android version. APK files) to install in the tester.
Analog camera test
Supports PAL & NTSC formats. The LCD screen's back light brightness, video image brightness,
contrast and color saturation are all adjustable.
PTZ controller
Displays and allows for analysis of analog video and controls Pan/tilt/zoom function of PTZ analog
cameras. For PTZ testing, setup the controlling parameters from the meter to match those of the camera:
e.g. PTZ protocol (PELCO-D, etc.), communication port (RS-485, etc.), baud rate, PTZ camera ID and
pan/tilt speed.
Enhanced Color bar generator
The tester sends out color bars via its BNC output to the monitor. This is used to test for a problem in

Page.9.
the cable going from the camera back to the monitoring area.
12VDC 2A power output port and 5VDC 2A USB power port
The unit can power a camera with its DC 12V 2A power output. Also included is a built in DC 5V 2A
power output port used to charge USB devices. NOTE: This USB port is for charging only and has no
ability to transfer data.
Audio testing
Test the audio from mic level input devices. Connect the tester and mic level device with the audio
cable. Supports audio recording and output. to monitor and / or record audio.
Cable tester
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting
status, cable type and the sequence of wires will be displayed, as well as display the serial number of
the cable tester kit.
PTZ data analysis
Search the Control protocol code from Multifunction keyboard or DVR by RS485 interface, test the
PTZ control command data whether received anomaly and RS485 data transmission.
Screen displays 16 hexadecimal codes such as
PELCO-P:A0 00（Add）xx xxxxxx AF xx
PELCO-D:FF 01（Add）xx xxxxxxxx
Digital Image zoom on the monitor
Set image zoom up to 4X to get a closer look at all the image detail. Supports analog and many IP
cameras
Video screenshot, record and playback
Capture the video image displayed and save as a JPEG file. You can also record and save the current
video to the SD card. The recorded files can play directly via Media player or under the function of
“Playback”.

Page.10.
Improvement color bar generator
Video generating, the PAL/NTSC multi-system color bar video generator and pure blue /black colorful
images, by receiving the video color bar to test the video channel whether transmit normally. And judge
whether the color is different, because of the transmission loss or interference, it suitable for Video
transmission of the field tests, such as optical video transmitter and receiver, video cable etc.
The new function color bar can test the image whether shift.
The color bar (red, green, blue, white, black) test the monitor whether have white or black dot etc.
DHCP dynamic address assignment
Built in DHCP server: Dynamically assign IP address for the IP camera or network device.
Access the dynamic IP address
The IP tester can directly access a dynamic IP address assigned from its DHCP server and use it as the
tester’s IP address. No need to set a IP address manually.
Multiple network IP Cameras Test
Supports Multi- segmented Static IP address setting which can simultaneously test different segments of
IP network Cameras.
IP address scan
The IP address scan can quickly search for connected IP cameras or another network device IP address.
PING Test
PING is the most conventional network debugging tool,it is used for testing if the connected IP camera
or other network equipment is working normally and the IP address is correct.
Port Finder
The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable
the installer to easily and quickly find the connected port for an Ethernet cable.
PoE Test

Page.11.
Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an
Ethernet cable.
LED Flashlight
Press the LED On/Off button to use the LED flashlight.
WIFI
With built in WIFI, you can view the video from a wireless camera (ONVIF or customized camera) or
connect to a Wireless network.
CVI camera test
HD CVI video surveillance testing, support720p 25,30,50,60fps / 1080p 25,30fps / 2560x1440P
25/30 fps, when CVI signal input, HD CVI camera image display, zoom, view photos, video
record and playback, Coaxial PTZ control and call up the camera OSD menu.
TVI camera test
HD TVI video surveillance testing, support720p 25,30,50,60fps/ 1080p 25,30fps/ 2048x1536P
18fps/ 2688x1520P 15fps/ 2560x1944P 12.5fps, when TVI signal input , HD TVI camera image
display, zoom ,view photos ,video record and playback .Coaxial PTZ control and call up the
camera OSD menu.
AHD camera test
AHD video surveillance testing, support 720p 25,30fps/ 1080p 25,30fps/ 2048x1536P 18,2
5,30fps/ 2560x1440P 15,25,30fps,when AHD signal input , AHD camera image display, z
oom ,view photos ,video record and playback ,Coaxial PTZ control and call up the came
ra OSD menu.
PoE power supply
Supports PoE 802.3at power at 48V and up to 24W.
HDMI signal output

Page.12.
The HDMI output port supports up to 1080p 60Hz resolution output.
Network bandwidth testing
The network bandwidth test needs two IP tester meters to test bandwidth: one as a transmitter, the other
as a receiver.
Screen image rotates 180 degrees
You can manually rotate the display 180 degrees using the settings.
FTP Server
Start the tester’s Wi-Fi or connect the tester’s LAN port to the network. Once the tester is online, start
its FTP Server and directly access files from the tester’s SD card. This also allows for the user to
upgrade the tester firmware.
2.4 Packing list
1). Tester
2). Adaptor DC12V 2A
3) Network cable tester
4) Polymer lithium ion battery (7.4V DC 5400mAh)
5). BNC cable
6). RS485 cable
7). Output Power cable
8). Audio cable
9). Safety cord
10). Tool bag
11). Manual
12).8GB SD card

Page.13.
2.5 Function interface

Page.14.
1
Press more than 2 seconds, turn on or off the device ,short press to turn on or off
the menu display
2
Menu key
3
4xzoom the image displays.
4
Far focus: Focus the image faraway
5
Near focus: Focus the image nearby
6
TELE: zoom in the image
7
WIDE: zoom out the image
8
Open/set ,Confirm the setting of parameters, open or enlarge the aperture
9
Return/Close : Return or cancel while setting parameters of the menu, close or
decrease the aperture
10
Upward, set function or add parameter. Tilt the PTZ upward
11
Rightward, select the parameter whose value will be changed. Add the value of the
parameter. Pan the PTZ right
12
Downward, set function or reduce the value of the parameter. Tilt the PTZ
downward
13
Leftward, select the parameter whose value will be changed
14
Confirm key
15
Return/Close : Return or cancel while setting parameters of the menu, close or
decrease the aperture
16
Patch
17
The charge indicator: it lights red while the battery is being charged. As the
charging is complete, the indicator turns off automatically
18
The RS485 data transmission indicator: it lights red while the data is being

Page.15.
transmitted
19
The data received indicator: it lights red while the data is being received
20
The power indicator: it lights green while the tester is powered on by the adapter
Top interface
Bottom interface
21
DC12V2A power output , for provisional DC power supply
22
HDMI IN
23
CVBS IN/AHD /TVI/CVI Coaxial interface /（BNC interface）
24
Video signal output（BNC interface）/ cable tracer interface
25
LED lamp
26
RS485 Interface: RS485communication for the PTZ
27
HDMI output interface
28
Micro SD card moveable,(comes with 8GB, supports up to 32GB)

Page.16.
29
UTP cable port: UTP cable tester port/ Cable tracer port
30
PSE power sourcing equipment. Tests PoE voltage
31
PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera)
32
Audio output and earphone interface
33
Audio input
34
USB 5V 2A power output (used only for power, not data)
35
DC12V2A charging interface
36
DC12V2A power output , for provisional DC power supply
3. Operation
3.1 Installing the Battery
The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery
cabin should be disconnected for safety during transportation!
Prior to the use of the instrument, the battery cables inside the battery cabin should be well
connected.
Usually it doesn’t need to disconnect the cable at the normal use
Pressing the key continuously can power on or off the tester.
Notice:Pls use the original adaptor and connected cable of the device!
When the battery icon is full or the charge indicator turns off automatically, indicate the battery
charging is completed.
Notice: When the Charge Indicator turns off, the battery is approximately 90% charged.
The charging time can be extended for about 1 hour and the charging time within 12 hours will not
damage the battery.
Notice :Press the key several seconds to restore the default settings when the
instrument works abnormally.