Yaesu FT-710 Use and care manual

3/27/23 (Revised)
FT-710 Firmware Update Information
Download the FT-710 [FT-710_Firmware_update_202303] from the following website:
https://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdI
D=615ADFEAB5EDBC65EBE1D64835F209DB&DivisionID=65&isArchived=0
[FT-710_Firmware_update_202303]zip Contains:
•MAIN: V01-09 /FT-710_MAIN_V0109.SFL 3/27/23 (New)
•DISPLAY: V01-07 /FT-710_DISPLAY_V0107.SFL 3/27/23 (New)
•DSP: V01-01 /FT-710_IFDSP_V0101.SFL 3/27/23 (New)
•SDR: V01-04 /FT-710_SDR_V0104.SFL 3/27/23 (New)
•Firmware_Ver_Up_Manual_ENG_FT-710_2211A 11/14/22
IMPORTANT:
After installing the firmware completely, the FT-710 MUST be RESET: Turn the Main Power
OFF, remove the SD card from the FT-710, then press [DSP REST] and [FINE/FAST] buttons
together, while pressing the Main Power ON. Main frequency display 7.000.000 MHz will
appear.
Implements improvements:
1. AESS settings can now be saved for each mode.
2. Improved DNR characteristics.
3. Changed the MENU notation of CW WAVE SHAPE.
4. Fixed a bug that MIC EQ was enabled in DATA mode.
5. Fixed a bug that some items were not reflected when calling QMB.
6. Fixed a bug that the band stack was not memorized properly when the power was
turned OFF.
7. Fixed a bug that the cursor position was not memorized in CURSOR mode.
8. Fixed the problem that the icon may be lost when the power is restarted with TUNER
ON.
9. Improvement to permit shifting to PMS with the CAT command.
10. The repeater shift frequency is reflected in the FA and FB commands.
11. Fixed a bug that CAT-AI was not output when operating PRESET items.
12. Fixed a bug in the operation of the EX command "TUN/LIN PORT SELECT".
13. Fixed the problem that the response was not performed normally when CAT
commands were received continuously.
14. Other improvements and optimizations have been made.

SD Card Preparation
Refer to FT710 Operation Manual (2211W-DS-3) Page 68 [Formatting a SD card].

How to Update the Firmware Version
When the update screen appears on the FT-710, a check mark will be in the [YAESU FT-710
FIRM UPDATE] Display, and then enter a check mark in all 4 boxes [MAIN, DISPLAY, DSP,
and SDR]. Refer to FT-710 Firmware Upgrade Manual. Now do the updates, and after the last
one has been completed, do a factory reset.
IMPORTANT:
After installing the firmware completely, the FT-710 MUST be RESET: Turn the Main Power
OFF, remove the SD card from the FT-710, then press [DSP REST] and [FINE/FAST] buttons
together, while pressing the Main Power ON. Main frequency display 7.000.000 MHz will
appear.
If you already have the above firmware versions, it is not necessary to update the FT-710 again.
We hope this new firmware will increase your enjoyment of your FT-710. Thank you for
choosing Yaesu radios. If you have any problems or questions, please contact Yaesu Amateur
Tech Support [e-mail].
Yaesu USA | 6125 Phyllis Drive | Cypress, CA 90630 | 714.827-7600 | FAX: [phone]
http://www.yaesu.com