Yale Z-Wave Plus v2 User manual

® ®
Yale Z-Wave Plus v2 Smart Module
Installation Guide
®
Adding a Yale Z-Wave Plus v2 Smart Module to your Assure Lock & Z-Wave System
1. Open Z-Wave system's smart home or alarm app and follow instructions for removing a device
4. Press the 3 key followed by the icon
2. On your lock keypad, enter your master entry code followed by the icon
5. Remove Yale Smart Module from slot above battery compartment
3. Press the 7 key followed by the icon
6. If you're adding a new Yale Smart Module, follow instructions included with it
• Reinstall batteries
IMPORTANT: Batteries must be removed before removing Yale Smart Module:
• Remove battery cover
• Remove Yale Smart Module
• Reinstall battery cover
• Remove batteries
P/N AYR-MOD-ZW3-MNL-0015 Rev A
®
®
Removing a Yale Z-Wave Plus v2 Smart Module from your Assure Lock & Z-Wave System
• Reinstall battery cover
2. Open Z-Wave system's smart home or alarm app on your smartphone or tablet
• Reinstall batteries
• Remove battery cover
• Remove batteries
3. If you have Smart Start* enabled with your Z-Wave System follow in-app prompts to add a new device
• Insert Yale Smart Module
If you don't have smart start or are not sure, follow steps 4 - 6
4. On your lock keypad, enter your master entry code followed by the icon
6. Press the 1 key followed by the icon
5. Press the 7 key followed by the icon
IMPORTANT: Batteries must be removed before inserting Yale Smart Module:
1. Install Yale Smart Module into slot above battery compartment
Please use this procedure only when network primary controller is
missing or otherwise inoperable.
If prompted, scan QR code
*SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a
controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10
minutes of being switched on in network vicinity.

!Warning: Changes or modifications to this device, not expressly approved by ASSA ABLOY
Residential Group could void the user's authority to operate the equipment.
24/7 Tech Support: 1-855-492-0505 • www.yalehome.com
Yale® is a registered trademark of ASSA ABLOY Residential Group. Other products' brand names may
be trademarks or registered trademarks of their respective owners and are mentioned for reference
purposes only. © Copyright 2020. All rights reserved. Reproduction in whole or in part without the
express written permission of ASSA ABLOY Residential Group is prohibited.
This device is a security enabled Z-Wave Plus v2 product that is able to use encrypted Z-Wave Plus v2 messages to
communicate to other security enabled Z-Wave Plus v2 products. This device must be used in conjunction with a
Security Enabled Z-Wave Controller in order to fully utilize all implemented functions. This product can be operated
in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Section 7.1.3 of RSS-GEN This Device complies with
Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: 1) this
device may not cause interference, and 2) this device must
accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS
standard exemptes de licence(s). Son fonctionnement est
soumis aux deux conditions suivantes: 1) ce dispositif ne
peut causer des interférences, et 2) cet appareil doit
accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
Class B Equipment
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
Interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
ŸReorient or relocate the receiving antenna.
FCC:
ŸConnect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Industry Canada:
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
ŸIncrease the separation between the equipment and
receiver.
Section 7.1.2 of RSS-GEN Under Industry Canada
regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
En vertu des règlements d'Industrie Canada, cet émetteur
radio ne peut fonctionner avec une antenne d'un type et un
maximum (ou moins) approuvés pour gagner de l'émetteur
par Industrie Canada. Pour réduire le risque d'interférence
aux autres utilisateurs, le type d'antenne et son gain
doivent être choisies de façon que la puissance isotrope
rayonnée équivalente (PIRE) ne dépasse pas ce qui est
nécessaire pour une communication réussie.
ŸConsult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
CAN ICES-3B/NMB-3B