Yamatake SDC10 Series User manual

1
Yamatake Corporation
Digital Controller SIO
Driver
1 System Configuration.......................................................................................................3
2 Selection of External Device............................................................................................8
3 Example of Communication Setting.................................................................................9
4 Setup Items....................................................................................................................65
5 Cable Diagram...............................................................................................................70
6 Supported Device.........................................................................................................103
7 Device Code and Address Code..................................................................................114
8 Error Messages............................................................................................................ 116

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 2
PREFACE
This manual describes how to connect the Display and the External Device (target Controller).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of External
Devices which can be connected and SIO type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External Device
to be connected and connection method.
)"2 Selection of External Device" (page 8)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting"
(page 9)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in off-line mode.
)"4 Setup Items" (page 65)
5Cable Diagram
This section shows cables and adapters
for connecting the Display and the
External Device.
)"5 Cable Diagram" (page 70)
Operation

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of Yamatake Corporation and the Display are
connected is shown.
Series CPU Link I/F SIO Type Setting
Example Cable Diagram
SDC10 C1005 Terminal block on
the controller RS422/485(2 wire)
Setting
Example 1
(page 9)
" Cable
Diagram5"
(page 89)
SDC15 C1503
C1506
Terminal block on
the controller RS422/485(2 wire)
Setting
Example 2
(page 11)
" Cable
Diagram6"
(page 96)
SDC20/21
C2003
C2005
C2010
C2104
C2107
C2109
Terminal block on
the controller RS232C Setting
Example 3
(page 13)
" Cable
Diagram 1"
(page 70)
C2002
C2004
C2009
C2103
C2106
C2108
Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 4
(page 15)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 5
(page 17)
" Cable
Diagram 3"
(page 75)
SDC25/26 C252
C262
Terminal block on
the controller RS422/485(2 wire)
Setting
Example 6
(page 19)
" Cable
Diagram6"
(page 96)
SDC30/31
C30040
C30041
C31045
C31446
C31546
Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 7
(page 21)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 8
(page 23)
" Cable
Diagram 3"
(page 75)
SDC35/36
C352
C354
C362
C364
Terminal block on
the controller RS422/485(2 wire)
Setting
Example 9
(page 25)
" Cable
Diagram6"
(page 96)
SDC40A
C40A3 Terminal block on
the controller RS232C Setting
Example 10
(page 27)
" Cable
Diagram 1"
(page 70)
C40A2 Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 11
(page 29)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 12
(page 31)
" Cable
Diagram 3"
(page 75)

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 4
SDC40B
C40B3 Terminal block on
the controller RS232C Setting
Example 13
(page 33)
" Cable
Diagram 1"
(page 70)
C40B2 Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 14
(page 35)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 15
(page 37)
" Cable
Diagram 3"
(page 75)
SDC40G C40G095 Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 16
(page 39)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 17
(page 41)
" Cable
Diagram 3"
(page 75)
DMC10 DMC10 Terminal block on
the controller RS422/485(2 wire)
Setting
Example 18
(page 43)
" Cable
Diagram4"
(page 82)
DCP31 P31A2 Terminal block on
the controller
RS422/485(4
wire)
Setting
Example 19
(page 45)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 20
(page 47)
" Cable
Diagram 3"
(page 75)
DCP32 P32A2 Terminal block on
the controller
RS422/
485(4wire)
Setting
Example 21
(page 49)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 22
(page 51)
" Cable
Diagram 3"
(page 75)
DCP551 DCP5512 Terminal block on
the controller
RS232C Setting Example 23
(page 53)
" Cable
Diagram 1"
(page 70)
RS422/485(4
wire)
Setting
Example 24
(page 55)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 25
(page 57)
" Cable
Diagram 3"
(page 75)
DCP552 DCP5522 Terminal block on
the controller
RS232C Setting Example 26
(page 59)
" Cable
Diagram 1"
(page 70)
RS422/
485(4wire)
Setting
Example 27
(page 61)
" Cable
Diagram 2"
(page 71)
RS422/485(2
wire)
Setting
Example 28
(page 63)
" Cable
Diagram 3"
(page 75)
Series CPU Link I/F SIO Type Setting
Example Cable Diagram

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 5
Connection Configuration
[Connection example 1:n]
[Connection example 1:n When using COM1 or COM2]
[Connection example 1:n When using COM1 and COM2]
*1 You can connect maximum 16 units of External Device. Note that maximum 15 units can be connected if
DMC10 is included.
• Do not add the termination resistance when the Controller to be connected using 1:n connection
includes the following series.
- SDC15
- SDC25/26
- SDC35/36
- DMC10
Display Controller
Display Controller
n*1
Controller Controller
n*1
Display
n*1
COM1 COM2
Controller Controller Controller
Controller Controller Controller

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 6
COM Port of IPC
When connecting IPC with External Device, the COM port which can be used changes with series and SIO type.
Please refer to the manual of IPC for details.
Usable port
Dip switch setting: RS-232C
Series Usable port
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
PS-2000B COM1*1 , COM2,
COM3*1, COM4
*1 The RI/5V can be switched. Please switch with the change switch of IPC.
--
PS-3650A, PS-3651A COM1*1 --
PS-3700A (Pentium®4-M)
PS-3710A COM1*1, COM2*1,
COM3*2 , COM4
*2 It is necessary to set up the SIO type with the Dip switch. Please set up as follows according to SIO
type to be used.
COM3*2 COM3*2
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
Dip switch Setting Description
1 OFF Reserve (always OFF)
2OFF
SIO type: RS-232C
3OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Does not Exist
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Does not Exist
9OFF
RS (RTS) Auto control mode: Disable
10 OFF

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 7
Dip switch setting: RS-422/485 (4 wire)
Dip switch setting: RS-422/485 (2 wire)
Dip switch Setting Description
1 OFF Reserve (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Does not Exist
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Does not Exist
9OFF
RS (RTS) Auto control mode: Disable
10 OFF
Dip switch Setting Description
1 OFF Reserve (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Exist
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Exist
9ON
RS (RTS) Auto control mode: Enable
10 ON

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 8
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Maker Select the maker of the External Device to be connected. Select "Yamatake Corporation".
Driver
Select a model (series) of the External Device to be connected and connection method.
Select "Digital Controller SIO".
Check the External Device which can be connected in "Digital Controller SIO" in system
configuration.
)"1 System Configuration" (page 3)
Use System Area Cannot use in this driver.
Port Select the Display port to be connected to the External Device.

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 9
3 Example of Communication Setting
Examples of communication settings of the Display and the External Device, recommended by Digital
Electronics Corp., are shown.
3.1 Setting Example 1
Setting of GP-Pro EX
Communication Settings
To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.
• When using SDC10, you need to set Wait To Send to 70ms or more.

Digital Controller SIO Driver
GP-Pro EX Device/PLC Connection Manual 10
Device Setting
To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific
Settings] of [Device/PLC Settings].
Settings of External Device
Use the PARA key, ENT key, down key and up key in front of the Controller for communication settings of the
External Device. Please refer to the manual of the Controller for more details.
Procedure
1.Press and hold the PARA key in operation mode (3 seconds) to move to the parameter mode.
2.Press and hold the PARA key in parameter mode (3 seconds) to move to the setup mode.
3.Press the PARA key several times to display the setup items.
4.Use the down/up keys to select the setting contents. (Setting value will blink.)
5.When you stop operating for 2 seconds, blinking of the setting value ends to confirm the change.
6.Press and hold the PARA key (3 seconds) to move to the standard display.
Setting Value
Setup Items Setting Value
C22 1
C23 0
• Parameters to be set vary depending on the Controller. Please refer to the manual of the Controller
for more details.