YASKAWA MP2300Siec User manual

MP23 iec
Hardware Manual
MP2300Siec
MP2310iec

Table of Contents
1
Table of Contents
1 Introduction
1.1 MP23iec Features - - - - - - - - - - - - - - - - - - - - - - 3
1.2 MP23iec Appearance - - - - - - - - - - - - - - - - - - - - 4
1.3 MP23iec Modules- - - - - - - - - - - - - - - - - - - - - - - 6
1.4 Dimensions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
2 Power Connections
5.1 Power Supply Connector - - - - - - - - - - - - - - - - - - - - - 9
5.2 System Connection Example (with E-Stop) - - - - - - - 11
3 Specifications
2.1 General Specifications - - - - - - - - - - - - - - - - - - - - - - 13
2.2 Product Specifications - - - - - - - - - - - - - - - - - - - - - - 14
2.3 Specifications of Controller - - - - - - - - - - - - - - - - - - - 15
4 Part Numbers
3.1 Component Model Numbers- - - - - - - - - - - - - - - - - - 17
4 Mounting
4.1 DIN Rail Method - - - - - - - - - - - - - - - - - - - - - - - - - - 19
6 EStop (RLY OUT) - MP2300Siec only
6.1 RLY OUT Connector Details- - - - - - - - - - - - - - - - - - 31
7 DIP Switches
7.1 Switch Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - 33
8 Self-Configuration
8.1 DIP Switch - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 35
9 LED Outputs
9.1 Indicators - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 37
10 Battery
10.1 Battery Installation - - - - - - - - - - - - - - - - - - - - - - - - 39

Table of Contents
2
11 MECHATROLINK-II
11.1 MECHATROLINK-II Connectors - - - - - - - - - - - - - - 41
12 Ethernet
12.1 Ethernet Connector Details- - - - - - - - - - - - - - - - - - 45
13 MECHATROLINK-II Devices
13.1 Devices Connectable via MECHATROLINK-II - - - - 49
14 Option Cards
14.1 AI-01 (Analog Input) Module - - - - - - - - - - - - - - - - - 51
14.2 AO–01 (Analog Output) Module - - - - - - - - - - - - - - 58
14.3 DO–01 (Digital Output) Module - - - - - - - - - - - - - - - 62
14.4 LIO-01/02 Module - - - - - - - - - - - - - - - - - - - - - - - - 67
14.5 LIO-04/05 Modules - - - - - - - - - - - - - - - - - - - - - - - 77
14.6 LIO-06 Module - - - - - - - - - - - - - - - - - - - - - - - - - - 92
15 Terminal Block Kits
15.5 CBK-U-MP2A-xx - - - - - - - - - - - - - - - - - - - - - - - - 105
15.6 CBK-U-MP2B-xx - - - - - - - - - - - - - - - - - - - - - - - - 106
15.7 CBK-U-MP2C-xx - - - - - - - - - - - - - - - - - - - - - - - - 107
16 Cable Shielding, Segregation & Noise Immunity 109
17 Firmware Upgrade Procedure - - - - - - - - - - - - - - - 111

1.1 MP23iec Features
3
1 Introduction
1.1 MP23iec Features
MP2300Siec and MP2310iec are small all-in-one machine controllers.
They are characterized by the following standard features:
Deterministic motion network MECHATROLINK-II
• Controls up to 16 axes of servos or inverters supporting
MECHATROLINK-II.
• Connects up to 21 total stations including remote I/O.
• Can include 6 virtual axes.
Ethernet (100Mbps)
• EtherNet/IP
• Modbus TCP
• Allows high-speed communications with MotionWorks IEC
• Enables communication with the application program by using a touch
panel
• Enables communication with the application program from another
controller

1.2 MP23iec Appearance
1.2.1 MP2300Siec Appearance
4
1.2 MP23iec Appearance
1.2.1 MP2300Siec Appearance
The following figure shows the external appearance of the Controller
with metal fittings for attachment. The dimensions in the figure do not
include the length of metal fittings.
Battery cover
MECHATROLINK- II
connector
(1 network, 2 ports)
DIP switch
(6 points+4 points)
Metal fittings
for attachment
LED
(8 points) MP LIO
3-pole connector
(24 VDC power supply)
Ethernet connector
with LEDs
2-pole connector
(RLY OUT)
Option slot
64 mm (2.52 in.)
130 mm(5.12 in.)
108 mm
(4.25 in.)
0001
23 Siec
0V
I/O
M-I/II

1.2 MP23iec Appearance
1.2.2 MP2310iec Appearance
5
1.2.2 MP2310iec Appearance
The following figure shows the external appearance of the Controller
100M
Ethernet
LINK
SW2
E-INIT
E-TEST ON
BATTERY
POWER
DC 0
DC24 M-I/II
RUN
ERR
BAT
SW1
RDY
ALM
MTX
STOP
SUP
INIT
CNFG
MON
TEST ON
IPTRX
MP2310iec
YASKAWA
DIP switch
(6 points+4 points)
LED
(8 points)
Battery cover
MECHATROLINK-II
connector
(1 line, 1 port)
3-pole connector
(24-V power supply)
Ethernet connector
with LED
Option Slots

1.3 MP23iec Modules
1.2.2 MP2310iec Appearance
6
1.3 MP23iec Modules
The following table shows the names and specifications of the
Controller and Option Modules.
Group Name Description Model Specifications
Option Modules
Motion
Modules
None currently supported
I/O Modules
Analog Input
Module AI-01 JAPMC-AN2300 Analog input, 8 channels
Analog Output
Module AO-01 JAPMC-AN2310 Analog output, 4 channels
Output Module DO-01 JAPMC-DO2300 64 outputs (sink mode output)
I/O Module LIO-01 JAPMC-IO2300
16 inputs, 16 outputs (sink mode
output)
1 encoder input
I/O Module LIO-02 JAPMC-IO2301
16 inputs, 16 outputs (source mode
output)
1 encoder input
I/O Module LIO-04 JAPMC-IO2303 32 inputs, 32 outputs
(sink mode output)
I/O Module LIO-05 JAPMC-IO2304 32 inputs, 32 outputs (source mode
output)
Multi-function
Option Card LIO-06 JAPMC-IO2305-E
8 digital inputs, 8 digital outputs (sink
mode), 1 analog input, 1 analog
output, 1 encoder input

1.4 Dimensions
1.4.1 MP2300Siec Controller
7
1.4 Dimensions
1.4.1 MP2300Siec Controller
/25KGE
Relay connector (2P)
Power connector (3P)
Terminating resistor
for MECHATROLINK
(attachment)
Model nameplate
DIN rail (35mm width)
(10: when DIN
rail is attached)
Units: mm
64 (42) 108
734-YE102
721-203/026-000
130
(9)
(14: when released)

1.4 Dimensions
1.4.2 MP2310iec Controller
8
1.4.2 MP2310iec Controller
* 1. The following cable-side connectors are attached to the power
connectors.
Power connector: 721-203/026-000
Note: Attachment
Handle for power connector (model: 231-131)
* These handles are used when connecting a cable to the cable-side
connector.
100M
Ethernet
LINK
RUN
ERR
BAT
SW1
SW2
RDY
ALM
MTX
STOP
SUP
INIT
CNFG
MON
TEST
E-INIT
E-TEST
ON
ON
BATTERY
POWER
DC 0V
DC24V
(4.5)
130
1214.5
(18) 108
120
111 4.5
(4.5)
111±0.2
Units: mm
121?0.2
Dimensions for mounting holes
4M4 taps
Four M4
mounting screws
Cable-end connector
(three poles)
721-203/026-000
M-I/II
IPTRX
MP2310
YASKAWA

2.1 Power Supply Connector
2.1.1 Specifications, Pin Arrangement, and Connection Procedure
9
2 Power Connections
2.1 Power Supply Connector
2.1.1 Specifications, Pin Arrangement, and Connection
Procedure
Supply 24VDC to the MP23iec. Connect the power supply
connector as shown in the diagram below.
Name Connector Name # of Pins Connector Model
Module Cable Manufacturer
Power Supply
Connector
POWER
3721-863 721-203/026 WAGO
Symbol Signal Name Description
24VDC
24V 24VDC input
0VDC
0V 0V input
FG Frame ground
(Ground to 100 or less.)
Use an insulated 24VDC power supply. Attach the power supply switch on the
AC side. If the switch is attached on the 24VDC side, there will be an inrush
current of approximately 40A when the power is turned ON.
DC
DC
24V
0V
POWER
AC input
24 VDC
0 V
24 VDC
0 V
24-VDC
power
MP2300Siec
POWER
FG FG
721-863
721-203/026
Wago Part #

2.1 Power Supply Connector
2.1.2 Connection Procedure
10
2.1.2 Connection Procedure
The power supply terminal has a removable connector. Use the
following procedure to wire the terminal to the power supply
connector. Use 0.2 mm2to 0.51 mm2(AWG24 to AWG20) twisted-
pair cable.
1. Strip approx. 6.5 mm from the end of the wire.
2. Open the wire insert opening on the terminal with the tool shown in
Fig. A or Fig. B.
3. Insert the wire into the opening and then close the opening by
releasing the lever or removing the screwdriver.
6.5 mm
Fig. A (with lever) Fig. B (with screwdriver)

2.2 System Connection Example (with E-Stop)
2.1.2 Connection Procedure
11
2.2 System Connection Example (with E-Stop)
Note: Only the MP2300Siec is equipped with an E-Stop connector.
The following diagram shows a 200 VAC power supply connection
example of a system using the MP2300Siec.
* Select the SERVOPACK, 24VDC power supply to use in accordance with the
input power supply specification.
2MC
1MC
1MC 2MC
1MC
SUP
SUP
RST
1MCCB
RA1
SUP
RA1
㧗24V
㧜
24 V
SGDS
L1
L2
L1C
L2C
B1/
B2
㧙
U
V
W
C
N
3
C
N
6
C
N
1
ޓޓޓ ޓޓޓ ޓޓޓ
R
S
T
㧞MC
㧝MC
r
t
PGMPGMPGMPGM
RA1
&%
4.;
176 'VJGTPGV
&%
8
.+0-
/
0V
MP2300Siec
;#5-#9#
6'56
4&;
#./
/6:
64:
470
'44
$#6
+2
59

59

/10
%0()
+06
572
5612
$#66'4;
㪧㪦㪮㪜㪩
'
M-I/II
+0+6
01
01
'6'56
*1
*1
*1
*1
SUP: Surge suppressor
200-VAC power supply
Noise filter Turn ON the
control power
Shut OFF the
control power
Turn ON the
servo power
Shut OFF the
servo power
Emergency
stop
Terminating Resistor
24-VDC
power
supply 1
24-VDC
power
supply 2
I/O module
Ground resistance:
100Wor less
Load
equipment
Panel Programming device
HUB
Machine
I/O
Terminating
resistance
SGDS SGDS SGDS
L1
L2
L1C
L2C
B1/
B2
㧙
C
N
3
C
N
6
C
N
1
U
V
W
L1
L2
L1C
L2C
B1/
B2
㧙
C
N
3
C
N
6
C
N
1
U
V
W
L1
L2
L1C
L2C
B1/
B2
㧙
C
N
3
C
N
6
C
N
1
U
V
W
(or switch network)

2.2 System Connection Example (with E-Stop)
2.1.2 Connection Procedure
12
This page left intentionally blank.

3.1 General Specifications
13
3 Specifications
3.1 General Specifications
Item Specifications
Environmental
Conditions
Ambient Operating
Temperature 0 to 55C
Ambient Storage
Temperature -25 to 85C
Ambient Operating
Humidity 30 to 95% (with no condensation)
Ambient Storage
Humidity 5 to 95% (with no condensation)
Pollution Level Pollution level 1 (conforming to JIS B 3501)
Corrosive Gas There must be no combustible or corrosive gas
Operating Altitude 2,000 m above sea level or lower
Mechanical
Operating
Conditions
Vibration
Resistance
Conforming to JIS B 3502:
• 10 to 57 Hz with single-amplitude of 0.075 mm
• 57 to 150 Hz with fixed acceleration of 9.8 m/s2
• 10 sweeps each in X, Y, and Z directions
(sweep time: 1 octave/min)
Shock Resistance
Conforming to JIS B 3502:
Peak acceleration of 147 m/s2(15 G) twice for 11 ms
each in the X, Y, and Z directions
Electrical
Operating
Conditions
Noise Resistance
Conforming to EN 61000-6-2, EN 55011 (Group 1,
Class A)
Power supply noise (FT noise): 2 kV min., for one
minute
Radiation noise (FT noise): 1 kV min., for one minute
Installation
Requirements
Ground Ground to 100 Max
Cooling Method Natural convection cooling

3.2 Product Specifications
14
3.2 Product Specifications
Item Specification
MP2300Siec MP2310iec
Number of Optional Slots 1 slot 3 slots
Number of Control Axes Up to 16 axes
MECHATROLINK-II
Communication System MECHATROLINK-II (32 byte)
Communication Cycle (M-II) 0.5 ms, 1.5 ms, 2.0 ms, 2.5 ms, 3.0 ms, 3.5 ms,
and 4.0 ms
Maximum Number of
Connectable Stations (M-II) 21 Slave nodes (up to 16 servo/inverter stations)
Ethernet Ethernet/IP
MODBUS TCP
100Base-TX
1 port
I/O On-board I/O (via option card)
Memory Capacity
SDRAM 32 MB
SRAM 512 KB (Battery backup)
FLASH 8 MB
Program Capacity 5.5 MB
Programming
Language
IEC 61131-3
Ladder Language Yes
Structured Text Yes
Function Block Diagram Yes
SFC Yes

3.3 Specifications of Controller
MP2300Siec Hardware Specifications
15
3.3 Specifications of Controller
MP2300Siec Hardware Specifications
Item Specifications
Classification Controller
Name MP2300Siec
Model Number PMC–U–MP23S (See page 17)
Power
Unit
Input Voltage 24VDC (20%)
Input Current 1A Max (during input/output rating)
Inrush Current 40A Max (full discharge state, during output rating, or the secondary
output of the external 24V power supply is turned ON)
Rated Voltage 5.0V
Rated Current 2.0A
Output Current Range 0.0 to 2.0A
Constant Voltage
Precision 2% Max (including input voltage and output load fluctuations)
Battery Battery for memory retention attachable
Motion Network
MECHATROLINK-II: 1 channel
SERVOPACK and I/O for up to 20 slave nodes connectable
(SERVOPACK for up to 16 axes)
Baud rate: 10 Mbps (MECHATROLINK-II)
Communication Function Ethernet: 100BASE-TX/10BASE-T
Calendar Seconds to year timer
(Battery backup)
Connectors Power supply to Ethernet RLY OUT
Indicators RDY(green), RUN(green), ALM(red), ERR(red), MTX(green),
BAT(red), TRX(green), IP(green), LINK(yellow), 100M(green)
Switches STOP, SUP, INIT, CNFG, MON, TEST, E-INIT, E-TEST
Current Consumption 1A Max
Dimensions (mm) 64 130 108 (W H D)
Mass 390 g
For the external 24V power supply, select a power supply which satisfies the
specifications below as well as the rated current (not more than 1A):
Allowable output load capacity: 1200F or more
Overcurrent detection is automatically restored by removing causes
However, except that the primary side (AC side) of the external 24V power
supply is turned ON/OFF.

3.3 Specifications of Controller
MP2310iec Hardware Specifications
16
MP2310iec Hardware Specifications
Item Specifications
Classification Basic Module
Name MP2310
Model Number JEPMC-MP2310-E
Power
Unit
Input Voltage 24VDC (20%)
Input Current* 1 A max. (during input/output rating)
Inrush Current* 40 A max. (full discharge state, during output rating, or the secondary
output of the external 24V power supply is turned ON)
Rated Voltage 5.0 V
Rated Current 2.0 A
Output Current Range 0.0 to 2.0 A
Constant Voltage
Precision 2% max. (including input voltage and output load fluctuations)
Battery Battery for memory retention attachable
Flash Memory 12 MB (User area 7.5 MBytes)
SDRAM 32 MB
SRAM
2 MB: M registers, S registers, trace memory, alarm history (battery backup)
Motion Network
MECHATROLINK: 1 channel
SERVOPACK and I/O for up to 21 stations connectable (SERVOPACK
for up to 16 axes)
Baud rate: 4 Mbps (MECHATROLINK-I) or 10 Mbps
(MECHATROLINK-II)
Communication Function Ethernet: 100BASE-TX/10BASE-T
Calendar Seconds to year timer
(Battery backup)
Connectors
POWER: Power supply connector
M-I/II: MECHATROLINK connector
Ethernet: Ethernet connector
Indicators RDY(green), RUN(green), ALM(red), ERR(red), MTX(green),
BAT(red), TRX(green), IP(green), LINK(yellow), 100M(green)
Switches STOP, SUP, INIT, CNFG, MON, TEST, E-INIT, and E-TEST
Current Consumption 1A max.
Dimensions (mm) 120 130 108 (W H D)
Mass 450 g
For the external 24V power supply, select a power supply which satisfies the
specifications below as well as the rated current (not more than 1A):
Allowable output load capacity: 1200F or more
Overcurrent detection is automatically restored by removing causes
However, except that the primary side (AC side) of the external 24V power
supply is turned ON/OFF.
Note: Recommended external 24V power supply: RTW24-2R2 (manufactured by TDK)

4.1 Component Model Numbers
17
4 Part Numbers
4.1 Component Model Numbers
System Components
Type Model Part Number Note
Controller Base
MP2300Siec
PMC-U-MP23S04 4 axis, no I/O module
PMC-U-MP23S08 8 axis, no I/O module
PMC-U-MP23S16 16 axis, no I/O module
PMC-U-MP23S04L1 4 axis, LIO-01 module
PMC-U-MP23S08L1 8 axis, LIO-01 module
PMC-U-MP23S16L1 16 axis, LIO-01 module
PMC-U-MP23S04L2 4 axis, LIO-02 module
PMC-U-MP23S08L2 8 axis, LIO-02 module
PMC-U-MP23S16L2 16 axis, LIO-02 module
MP2310iec
PMC-U-MP23104 4 axis, no I/O module
PMC-U-MP23108 8 axis, no I/O module
PMC-U-MP23116 16 axis, no I/O module
Accessories
Battery JZSP-BA01 Replacement
Panel Mounting Bracket JEPMC-OP2300S-E Only required for screw mounting
DIN Rail Clips for
MP2000iec JEPMC-OP300 Set of 2 clips
RLY OUT Connector 734-YE102 Replacement (MP2300Siec only)
Power Supply
Connector 721-203/026 Replacement
I/O Option cards
AI-01 (Analog inputs) JAPMC-AN2300
MP2300Siec:
Select one local I/O module
MP2310iec:
Select up to 3 local I/O modules
AO-01 (Analog outputs) JAPMC-AN2310-E
DO-01 (Digital outputs) JAPMC-DO2300
LIO-01 (16 in, 16 out,
enc) JAPMC-IO2300
LIO-02 (16 in, 16 out,
enc) JAPMC-IO2301
LIO-04 (32 in, 32 out) JAPMC-IO2303
LIO-05 (32 in, 32 out) JAPMC-IO2304
LIO-06 (Multi-function
card) JAPMC-IO2305-E
Other
I/O
IO2310/IO2330
(64 Point I/O Module)
JEPMC-IO2310
JEPMC-IO2330
IO2310: Sinking Output Type
IO2330: Sourcing Output Type
Ethernet Cable N/A Use common shielded ethernet cable

4.1 Component Model Numbers
18
Option Card
Cables (Pigtail)
AI-01 JEPMC-W6080-xx
xx denotes length:
A5: 0.5 meter
01: 1.0 meter
03: 3.0 meter
AO-01 JEPMC-W6090-xx
LIO-01 / LIO-02 JEPMC-W2061-xx
LIO-04 / LIO-05 / DO-01 JEPMC-W6060-xx
LIO-06 JEPMC-W2064-xx-E
Terminal Block Kits
LIO-01 / LIO-02 CBK-U-MP2A-xx xx denotes length
A5: 0.5 meter
01: 1.0 meter
03: 3.0 meter
LIO-04 / LIO-05 / LIO-06 CBK-U-MP2B-xx
IO2310/IO2330
(64 Point I/O Module) CBK-U-MP2C-xx
MECHATROLINK-II Cables
Network cable with
connector at both ends JEPMC-W6002-xx xx denotes length: 0.5 meter
1.0 meter
3.0 meter
5.0 meter
10.0 meter
20.0 meter
30.0 meter
40.0 meter
50.0 meter
Network cable with
connector at both ends,
including ferrite core
JEPMC-W6003-xx
Network Termination
Resistor JEPMC-W6022 Resistor built into connector plug
Software
MotionWorks IEC
Express PDE-U-IESx denotes MotionWorks IEC Version
C = 1 2 = 2
x denotes number of software licenses
A = 1 B = 5 C = 10
MotionWorks IEC Pro PDE-U-IEPx
OPC Server PDE-U-OPCPx x denotes number of software licenses
A = 1 B = 5 C = 10 D = 20
System Components
Type Model Part Number Note