YASKAWA A1000 Series User manual

Custom Software Supplement
MANUAL NO. TM.A1000SW.029
To properly use the product, read this manual thoroughly and retain
for easy reference, inspection, and maintenance. Ensure the end user
receives this manual.
Software Number: VSA91019□
Drive Models: AU□A□□□□□□□
Traverse Application
YASKAWA AC Drive-A1000

YASKAWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 3
Table of Contents
1 PREFACE AND SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 PRODUCT OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 APPLICATION SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Refer to the A1000 Technical Manual for content not described in this document.
Copyright © 2013 YASKAWA ELECTRIC CORPORATION
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of
Yaskawa. No patent liability is assumed with respect to the use of the information contained herein. Moreover, because
Yaskawa is constantly striving to improve its high-quality products, the information contained in this manual is subject to
change without notice. Every precaution has been taken in the preparation of this manual. Yaskawa assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information
contained in this publication.

4YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
This Page Intentionally Blank

1 Preface and Safety
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 5
1 Preface and Safety
Yaskawa manufactures products used as components in a wide variety of industrial systems and equipment. The selection
and application of Yaskawa products remain the responsibility of the equipment manufacturer or end user. Yaskawa
accepts no responsibility for the way its products are incorporated into the final system design. Under no circumstances
should any Yaskawa product be incorporated into any product or design as the exclusive or sole safety control. Without
exception, all controls should be designed to detect faults dynamically and fail safely under all circumstances. All systems
or equipment designed to incorporate a product manufactured by Yaskawa must be supplied to the end user with
appropriate warnings and instructions as to the safe use and operation of that part. Any warnings provided by Yaskawa
must be promptly provided to the end user. Yaskawa offers an express warranty only as to the quality of its products in
conforming to standards and specifications published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR
IMPLIED, IS OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses, or claims
arising from misapplication of its products
Applicable Documentation
The following manuals are available for the A1000 Drive:
Supplemental Safety Information
Read and understand this manual and the A1000 Quick Start Guide before installing, operating, or servicing this option
unit. Install the drive according to the A1000 Quick Start Guide and local codes. Observe all cautions and warnings in this
document and the standard drive technical manuals.
Refer to the A1000 Quick Start Guide and Technical Manual for safety information and to install and start-up the drive.
This document is a supplement to the standard drive technical manual. It describes the effects on the drive parameters and
functions with the software installed.
• Custom software is provided to add functionality to a standard drive to enhance or enable use in a specific application.
• The software is loaded to the flash ROM area of the control board, and replaces the standard drive software.
Obtaining Support
When seeking support for a drive with custom software, it is imperative to provide the unique part number shown on the
drive nameplate. The software is flashed to the control board memory and the operation of parameters, functions, and
monitors are different than the standard drive software, as described herein.
Refer to Yaskawa office locations listed on the back cover of this manual.
Custom Software Supplement
Yaskawa AC Drive - Traverse Application A1000 Custom Software Supplement
Manual No: TM.A1000SW.029
Read this manual first. This supplement is an addendum to the A1000 Quick Start Guide and Technical Manual. It lists the
effects of this custom software on the parameters in the drive and function descriptions in the manual.
To obtain the supplement access this site: U.S: http://www.yaskawa.com
Yaskawa Drive
Yaskawa AC Drive -
A1000 Quick Start Guide
To obtain instruction manuals for Yaskawa products access these sites:
U.S.: http://www.yaskawa.com
Europe: http://www.yaskawa.eu.com
Japan: http://www.e-mechatronics.com
Other areas: contact a Yaskawa representative.
For questions, contact the local Yaskawa sales office or the nearest Yaskawa
representative.
Yaskawa AC Drive -
A1000 Technical Manual
SUPPLEMENT

6 YASKAWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
2 Product Overview
2 Product Overview
About This Product
This custom software is designed specifically for use in Traverse applications.
Applicable Models
This custom Traverse application software is available for the A1000 drive models listed in Table 1.
Table 1 Applicable Models
Voltage Class Models Software Version <1>
<1> See “PRG” on the drive nameplate for the software version number.
200 V Three-Phase AU2A0004F to 2A0211F,
AU2A0250A to 2A0415A VSA91019
400 V Three-Phase AU4A0002F to 4A0165F,
AU4A0208A to 4A0675A VSA91019
600 V Three-Phase AU5A0003F to 5A0099F,
AU5A0125A to 5A0242A VSA91019

3 Application Selection
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 7
3 Application Selection
Traverse Anti-Phase
Overview
The Traverse Anti-Phase function controls the traverse arm of a winder in textile industry applications. This function
generates a dithered disturbed waveform that is used as frequency reference for the traverse arm drive and also provides
an anti-phase signal for output to a spindle slave drive for better winding.
Basic Concept
When the drive reaches the set frequency reference, the output frequency waveform is modulated in a triangle type
pattern. This randomizes fiber overlap on the spindle, producing a tighter wrap and a higher quality wound package.
P1 parameters are used to set the attributes of a disturbed waveform, which is essentially a triangle wave with
instantaneous jumps at the peak and trough. This triangle wave rides on top of the base frequency reference for the
traverse drive.
The signal(s) output to control the slave spindle drive can be set to one of three new monitors:
• U7-02 - Absolute Slave Frequency
• U7-03 - Ripple Slave Frequency
• U7-04 - Slave Base Frequency
The Absolute and Ripple Slave Frequency monitors have an anti-phase component to them, outputting a disturbed
waveform that is the inverse (anti-phase) of the master disturbed waveform. The anti-phase waveform ignores the jump
portion of the master traverse disturbed waveform.
Limitations
• The following languages are supported: English, Japanese, Spanish, German, French, Italian, and Portuguese.
• Parameter L4-02, Speed Agree Detection Width, should be set to a small, nonzero value to avoid unintended jumps in
the disturbed waveforms.
• When P1-04 and P1-05 are set to short slope times, set L4-02 to a value greater than 0.5 Hz to prevent inconsistent
traverse operation.
• Step changes in frequency reference will result in unintended jumps in the disturbed waveforms. Disable the Traverse
function using the 80h (Disturbed WF Off) digital input to prevent damage to the motor or connected equipment.
• The Traverse waveform can be configured to be smaller than the input resolution of the A1000 slave drive's frequency
reference. Ensure that Master Frequency Reference × P1-02 is significantly larger than (Slave Max Output Freq/2048)
for proper control of the slave drive.

3 Application Selection
8YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
Control Modes, Symbols, and Terms
The table below lists terms and symbols used in this section to indicate which parameters are available in which control
modes.
Description
Parameter is available in all control modes.
Parameter is available when operating the drive with V/f Control.
Parameter is available when operating the drive with V/f with PG Control.
Parameter is available when operating the drive with Open Loop Vector.
Parameter is available when operating the drive with Closed Loop Vector.
Parameter is available when operating the drive with Open Loop Vector for PM monitors.
Parameter is available when operating the drive with Advanced Open Loop Vector for PM monitors.
Parameter is available when operating the drive with Closed Loop Vector for PM monitors.
All Modes
V/fV/f
V/f w PGV/f w PG
OLVOLVOLVOLV
OLVCLV
V/f w PGOLV/PM
V/f w PGAOLV/PM
CLV/PM

3 Application Selection
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 9
Related Parameters and Functions
The following parameters are used to set up the drive for operation with the software. Available parameter settings are
listed based upon which drive control modes are active, as listed in the Control Mode Access Level column in the
following tables.
Confirm proper setting of the parameters beginning with Table 2.
Table 2 Modified Parameters
Table 3 Additional Parameters
Table 4 Group Text
No.
(Addr.
Hex)
Parameter Name
Digital Operator
Display
Description Values
Change
during
Run
Control Mode
Access Level
A1-00
(100h) Language Selection
Select Language
0: English
1: Japanese
2: German
3: French
4: Italian
5: Spanish
6: Portuguese
Default: 0
Range: 0 to 6 No
No.
(Addr.
Hex)
Parameter Name
Digital Operator
Display
Description Values
Change
during
Run
Control Mode
Access Level
P1-01
(600h)
Disturbed Waveform
Selection
Disturb WF Sel
Enables and disables the traverse disturbed
waveform function.
0: Disabled
1: Enabled
Default: 0
Range: 0 to 1 Yes
P1-02
(601h)
Disturbed Waveform
Amplitude
Disturb WF Amp
Sets the amplitude of the disturbed waveform as a
percentage of the commanded frequency reference.
Note: Setting this parameter to 0.0 disables the
Transverse function.
Default: 0.0
Range: 0.0 to 20.0 % Yes
P1-03
(602h)
Disturbed Waveform Jump
Disturb WF Jmp
Adds a notch or jump below the peak amplitude of
the disturbed waveform when set to a non-zero
value. Set as a percentage of the Disturbed
Waveform Amplitude (P1-02).
Default: 0.0
Range: 0 to 50.0% Yes
P1-04
(603h)
Negative Slope Time
Neg Slope Time
Sets the time for the disturbed waveform to
decelerate from the maximum value
(reference + P1 02) to the minimum value
(reference - P1-02).
Note: Setting this parameter to 0.0 seconds disables
the Transverse function.
Default: 0.0
Range: 0.0 to 120.0 s Yes
P1-05
(604h)
Positive Slope Time
Pos Slope Time
Sets the time for the disturbed waveform to
accelerate from the minimum value
(reference - P1 02) to the maximum value
(reference + P1-02).
Note: Setting this parameter to 0.0 seconds disables
the Transverse function.
Default: 0.0
Range: 0.0 to 120.0 s Yes
P1-06
(605h)
Slave Scan Offset
Slv Scan Offset
Monitor shift (U7-02, U7-03, and U7-04) in ms to
compensate for systematic delays.
Default: 0 ms
Range: -24 ~ 24 ms Yes
Function Group Group Name
Digital Operator Display
PTraverse Group
Traverse
All Modes
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f

3 Application Selection
10 YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
Table 5 Function Text
Table 6 Monitor Function Text
Table 7 Monitors
Table 8 Multi-function Input Settings (H1-)
Table 9 Multi-function Output Settings (H2-)
Function Group Function Name
Digital Operator Display
P1 Disturbed Waveform Adjustment
Disturb WF Adj
Function Group Monitor Name
Digital Operator Display
U7 Traverse Monitors
Traverse
No.
(Addr.
Hex)
Monitor Name
Digital Operator Display Description Analog Output Scaling Unit Control Mode Access Level
U7-02
(661h)
Absolute Slave Frequency
Slv Abs Freq
Base frequency reference summed with the
anti-phase dither.
10V: Maximum
Frequency
(E1-04)
0.01 Hz
U7-03
(662h)
Ripple Slave Frequency
Slv Ripple Freq Anti-phase dither alone.
10V: Maximum
Frequency
(E1-04)
0.01 Hz
U7-04
(663h)
Base Slave Frequency
Slv Base Freq
Base frequency reference (before disturbed
waveform is applied).
10V: Maximum
Frequency
(E1-04)
0.01 Hz
Setting Description Control Mode
Access Level
80h
Disturbed WF Off
Open: Disturbed waveform enabled
Closed: Disturbed waveform disabled
Setting Description Control Mode
Access Level
40h
Disturb UP Sts
Open: The disturbed waveform frequency is decreasing
Closed: The disturbed waveform frequency is increasing
41h
During Disturb
Open: Disturbed waveform disabled
Closed: Disturbed waveform being generated
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f
OLV
OLV/PM
V/fV/f

3 Application Selection
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 11
Function Description
Machine Parameter Selection
The disturbed waveform begins once the drive reaches Speed Agree. The disturbed waveform rides on top of the base
frequency reference for the traverse drive. The output will be the frequency reference waveform summed with the
disturbed waveform if the frequency reference of the master drive is adjusted while the disturbed waveform is active.
The dithering is a triangle waveform with amplitude and slope set by P1-02, P1-04, and P1-05 parameters. The traverse
drive also has a jump in the dithering wave form which is set by parameter P1-03.
The anti-phase output signal is the disturbed portion of the traverse frequency reference signal inverted. Only the triangle
portion of the disturbed waveform is used for the anti-phase. The jump is ignored.
The Traverse application software has three monitors:
• Base Slave Frequency (U7-04)
U7-04, Base Slave Frequency, outputs the frequency reference of the master (traverse) before the disturbed waveform
is applied.
• Ripple Slave Frequency (U7-03)
U7-03, Ripple Slave Frequency, outputs the anti-phase of the disturbed portion of the waveform.
• Absolute Slave Frequency (U7-02)
U7-02, Absolute Slave Frequency, outputs the anti-phase of the disturbed portion of the waveform summed with U7-04.
To compensate for system delays, U7-02, U7-03, and U7-04 monitors can be set to lead or lag the traverse control output
by up to 24 scans (24 ms), set by P1-06.
All three monitors can be set to analog outputs. U7-02 or U7-03 would generally be used as an analog output going to the
slave (spindle) for its frequency reference. U7-02 provides the slave a complete reference signal. U7-03 is used as a dither
reference if the slave is to use its own base frequency reference as shown in Figure 1.

3 Application Selection
12 YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
Application Example
Figure 1
Figure 1 Software and Hardware Configuration for A1000 Traverse
Master Parameter Changes
• H2-01 = 41h: Provide during disturb status output to slave.
• H4-01 = 703: Provide disturbed frequency ripple to slave.
• H4-07 = 1: Provide a bipolar analog output signal.
• P1-01 = 1: Enable Traverse functionality.
• P1-02 ~ P1-05 = application requirements: Define the characteristics of the disturbed frequency.
• P1-06 = application requirement: Define scan offset to account for system delays.
Slave Parameter Changes
• C1-03 = 0.0 sec: Set acceleration time 2 to 0.0 seconds.
• C1-04 = 0.0 sec: Set deceleration time 2 to 0.0 seconds.
• H1-08 = 7: Switch between accel/decel time 1/2 based on During Disturb output.
• P1-01 = 1: Enable Traverse functionality.
• DIP Switch S1 = V: Enable voltage input to A2.
• H3-09 = 1: Set A2 to a -10V to +10V bipolar input.
Implementation
Situation 1: Standard Operation
When programmed with the settings as shown in Table 10, the Traverse software produces output waveforms similar to
the ones in Figure 2. Using these settings and a reference frequency of 45 Hz, the master drive operates based on the
triangle waveform with 9 Hz (peak-peak) amplitude. Because the waveform is centered on the 45 Hz reference frequency,
the master waveform oscillates between 36 and 54 Hz while in Traverse mode.
Table 10 Sample Operating Parameters
Parameter Name Setting
P1-01 Disturbed Waveform Selection 1
P1-02 Disturbed Waveform Amplitude 20.0%
P1-03 Disturbed Waveform Jump 50.0%
P1-04 Negative Slope Time 5.0 s
P1-05 Positive Slope Time 4.0 s
P1-06 Slave Scan Offset 0 ms
A 1000 (Master)
Traverse Software
MA
MC
A1000 (Slave)
Standard Software
S8
SC
A2
AC
FM
AC
DIP Switch S1
VI
A1+
-
Slave
Frequency
Reference
H3-09 = 1
H1-08 = 7
H4-01 = 703
H2-01 = 41

3 Application Selection
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 13
U7-02, Slave Absolute Frequency, (available as an output to the slave by setting parameter H4-01 to 702), has the same
amplitude of 9 Hz (calculated by P1-02 ×Reference Frequency). U7-02 is anti-phase to the master waveform and is
centered around U7-04, the Slave Base Frequency. Since the Slave Base Frequency is 45 Hz, U7-02 varies from
36 to 54 Hz while in Traverse mode. Before entering Traverse mode, the Slave Absolute Frequency will rest at 48 Hz, as
represented by the equation in Figure 2.
U7-03, Slave Ripple Frequency, is the same as the U7-02 waveform without the Slave Base Frequency component. Slave
Ripple Frequency U7-03 is a bipolar waveform centered at 0 Hz. The output varies from 21 to 39 Hz during operation.
The Slave Ripple Frequency will rest at 3 Hz before entering Traverse mode as represented by the equation in Figure 2.
Figure 2
Figure 2 Master and Slave Output Diagram: Standard Operation
Run Command
Frequency
Reference
Disturb UP Status
multi-function output
During Disturbed
multi-unction output
Speed Agree
P1-04 P1-05
U7-04
Slave Base
Frequency
U7-02
Slave Absolute
Frequency
P1-02 x Freq Ref
P1-02 x Freq Ref x P1-03
0 Hz
U7-03
Slave Ripple
Frequency
P1-02 x
Freq Ref
0 Hz
P1-02 x Freq Ref x P1-03
2 - P1-03
P1-02 x Freq Ref x P1-03
P1-02 x Freq Ref
P1-02 x Freq Ref
P1-02 x Freq Ref
2 - P1-03
P1-02 x Freq Ref
P1-02 x Freq Ref x P1-03

3 Application Selection
14 YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
Situation 2: Traverse Operation Exceeds Maximum Output Frequency
Using the same parameter settings in Table 10 and a reference frequency of 52 Hz, the Traverse software will
produce output waveforms similar to the ones in Figure 3. The Traverse software, with an amplitude of
10.4 Hz, will produce a triangle output that varies from 41.6 to 62.4 Hz. Setting the drive parameter E1-04 to
60.0 Hz caps the triangle waveform when the traverse frequency exceeds the Maximum Output Frequency of
60 Hz.
Figure 3
Figure 3 Traverse Mode Operation Outside of Max Output Frequency Parameter E1-04 / E3-04
Situation 3: Changing Reference Frequency
Using the parameter settings found in Table 10 and a reference frequency that changes from 20 Hz to 30 Hz, the Traverse
software will produce output waveforms similar to those in Figure 4. Using the 20 Hz frequency reference, the master
drive oscillates between 16 and 24 Hz. When the reference frequency increases to 30 Hz, the drive exits Traverse mode
and accelerates using the default acceleration time set in parameter C1-01. When the drive reaches the new frequency
reference, it re-enters Traverse mode and the master drive oscillates between 24 and 36 Hz.
Initially, U7-02, Slave Absolute Frequency, rests at 21.33 Hz. When the drive enters Traverse mode, U7-02 oscillates
between 16 and 24 Hz. When the reference frequency changes, the drive exits Traverse mode and the Slave Absolute
Frequency rises to 32 Hz until the drive re-enters Traverse mode. Once resuming traverse mode, the new waveform
oscillates between 24 and 36 Hz.
U7-03, Slave Ripple Frequency, operates similar to U7-02, except that its waveform remains centered at 0 Hz.
Step changes in frequency reference will result in unintended jumps in the disturbed waveforms. Disable the Transverse
function using the 80h, (Disturbed WF Off), to prevent damage to the motor or connected equipment before making large
changes in the frequency reference.
Run
Command
Frequency
Reference
Disturb UP Status
Multi-function output
Multi-function output
During Disturbed
Speed Agree
0Hz
0Hz
E1-04
Maximum
Frequency
Slave Base
Frequency
Slave Base
Frequency
Slave Absolute
Frequency
U7-02
U7-04
U7-03
E1-04

3 Application Selection
YAS K AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement 15
Figure 4
Figure 4 Traverse Mode Operation with Changing Frequency Reference
Run Command
Frequency
Reference
P1
-
02 x
Freq Ref
Disturb UP Status
Multi-Function Output
Multi-Function Output
During Disturbed
Speed Agree
0 Hz
P1-04 P1-05
U7-03
Slave Ripple Frequency
P1-02 x
Freq Ref*
P1-05P1-04
Accel Time 1
Accel Time 1
Slave Base Frequency
U7-02 U7-04
Slave Absolute
Frequency
80h
Disturbed WF OFF
(C1-01)
P1-02 Freq Ref
P1-02 x Freq Ref x P1-03
P1-02 x Freq Ref x P1-03
P1-02 x Freq Ref x P1-03
P1-02 x Freq Ref
2 - P1-03
P1-02 x Freq Ref x P1-03
2 - P1-03 P1-02 x
Freq Ref
P1-02 x Freq Ref x P1-03
2 - P1-03
P1-02 x Freq Ref x P1-03
2 - P1-03
P1-02 x Freq Ref* P1-02 x Freq Ref*
P1-02 x Freq Ref*
P1-02 x Freq Ref*
P1-02 x Freq Ref*
(C1-01)
P1-02 x Freq Ref* x P1-03
P1-02 x Freq Ref* x P1-03
2 - P1-03
2 - P1-03
P1-02 x Freq Ref* x P1-03
P1-02 x Freq Ref*
P1-02 x Freq Ref* x P1-03
0 Hz

3 Application Selection
16 YASK AWA TM.A1000SW.029 Traverse Application A1000 Custom Software Supplement
Revision History
The revision dates and the numbers of the revised manuals appear on the bottom of the back cover.
Date of Publication Revision Number Software Number Revised Content
April 2013 - VSA910190 First release
MANUAL NO.ޓTM.A1000SW.029
Published in U.S.A. April 2013 10-4
Date of
publication
Date of original
publication
Revision number
0

YASKAWA AMERICA, INC.
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone: (800) YASKAWA (927-5292) or 1-847-887-7000 Fax: [phone]
http://www.yaskawa.com
DRIVE CENTER (INVERTER PLANT)
2-13-1, Nishimiyaichi, Yukuhashi, Fukuoka, 824-8511, Japan
Phone: [phone] Fax: [phone]
http://www.yaskawa.co.jp
YASKAWA ELECTRIC CORPORATION
New Pier Takeshiba South Tower, 1-16-1, Kaigan, Minatoku, Tokyo, 105-6891, Japan
Phone: [phone] Fax: [phone]
http://www.yaskawa.co.jp
YASKAWA ELÉTRICO DO BRASIL LTDA.
Avenda Fagundes Filho, 620 Bairro Saude, São Paulo, SP04304-000, Brasil
Phone: [phone] Fax: [phone]
http://www.yaskawa.com.br
YASKAWA EUROPE GmbH
Hauptstrasse 185, 65760 Eschborn, Germany
Phone: [phone] Fax: [phone]
http://www.yaskawa.eu.com
YASKAWA ELECTRIC UK LTD.
1 Hunt Hill Orchardton Woods, Cumbernauld, G68 9LF, United Kingdom
Phone: [phone] Fax: [phone]
http://www.yaskawa.co.uk
YASKAWA ELECTRIC KOREA CORPORATION
7F, Doore Bldg. 24, Yeoido-dong, Yeoungdungpo-gu, Seoul, 150-877, Korea
Phone: [phone] Fax: [phone]
http://www.yaskawa.co.kr
YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.
151 Lorong Chuan, #04-01, New Tech Park, 556741, Singapore
Phone: [phone] Fax: [phone]
http://www.yaskawa.com.sg
YASKAWA ELECTRIC (SHANGHAI) CO., LTD.
No. 18 Xizang Zhong Road, 17F, Harbour Ring Plaza, Shanghai, 200001, China
Phone: [phone] Fax: [phone]
http://www.yaskawa.com.cn
YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE
Room 1011, Tower W3 Oriental Plaza, No. 1 East Chang An Ave.,
Dong Cheng District, Beijing, 100738, China
Phone: [phone] Fax: [phone]
YASKAWA ELECTRIC TAIWAN CORPORATION
9F, 16, Nanking E. Rd., Sec. 3, Taipei, 104, Taiwan
Phone: [phone] Fax: [phone]
In the event that the end user of this product is to be the military andsaid product is to be employed in any weapons systems or the manufacture
thereof, the export will fall underthe relevant regulations asstipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure
to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may ap ply.
Specifications are subjectto change without notice for ongoing product modifications and improvements.
©2013 YASKAWA AMERICA, INC. All rights reserved.
Published in U.S.A. April 2013 04-13
MANUAL NO. TM.A1000SW.029
YASKAWA AMERICA, INC.
Custom Software Supplement
Traverse Application
YASKAWA AC Drive-A1000
1