YASKAWA PS-V10S User manual

24 V制御電源ユニット
V1000オプションユニット
取扱説明書
形式：PS-V10S, PS-V10M
24 V Power Supply
YASKAWA AC Drive-V1000 Option
Installation Manual
Type: PS-V10S, PS-V10M
To properly use the product, read this manual thoroughly and retain
for easy reference, inspection, and maintenance. Ensure the end user
receives this manual.
製品を安全にお使い頂くために，本書を必ずお読みください。
また，本書をお手元に保管していただくとともに，最終的に本製品をご使用になる
ユーザー様のお手元に確実に届けられるよう，お取り計らい願います。
MANUAL NO. TOBP C730600 27B

2YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
Copyright ©2007 YASKAWA ELECTRIC CORPORATION
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, mechanical, electronic, photocopying,
recording, or otherwise, without the prior written permission of Yaskawa. No patent liability
is assumed with respect to the use of the information contained herein. Moreover, because
Yaskawa is constantly striving to improve its high-quality products, the information
contained in this manual is subject to change without notice. Every precaution has been
taken in the preparation of this manual. Yaskawa assumes no responsibility for errors or
omissions. Neither is any liability assumed for damages resulting from the use of the
information contained in this publication.

YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 3
Table of Contents
1 PREFACE AND SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 PRODUCT OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 RECEIVING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 24 V POWER SUPPLY OPTION COMPONENTS . . . . . . . . 11
5 INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . .12
6 VERIFYING OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7 DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

4 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
1 Preface and Safety
1 Preface and Safety
Yaskawa manufactures products used as components in a wide variety of industrial systems
and equipment. The selection and application of Yaskawa products remain the responsibility
of the equipment manufacturer or end user. Yaskawa accepts no responsibility for the way its
products are incorporated into the final system design. Under no circumstances should any
Yaskawa product be incorporated into any product or design as the exclusive or sole safety
control. Without exception, all controls should be designed to detect faults dynamically and
fail safely under all circumstances. All systems or equipment designed to incorporate a
product manufactured by Yaskawa must be supplied to the end user with appropriate
warnings and instructions as to the safe use and operation of that part. Any warnings
provided by Yaskawa must be promptly provided to the end user. Yaskawa offers an express
warranty only as to the quality of its products in conforming to standards and specifications
published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS
OFFERED. Yaskawa assumes no liability for any personal injury, property damage, losses,
or claims arising from misapplication of its products
◆Applicable Documentation
The following manuals are available for the 24 V Power Supply Option:
24 V Power Supply Option
Yaskawa AC Drive-V1000 Option
24 V Power Supply
Installation Manual
Manual No.: TOBPC73060027
(This book)
Read this manual first.
The installation manual is packaged
with the 24 V Power Supply Option
and contains basic installation and
wiring required for proper use of this
product.
Yaskawa Drive
Yaskawa AC Drive-V1000
Quick Start Guide
To obtain instruction manuals for
Yaskawa products access these sites:
U.S.: http://www.yaskawa.com
Europe: http://www.yaskawa.eu.com
Japan: https://www.e-mechatronics.com
Other areas: contact a Yaskawa
representative.
For questions, contact the local
Yaskawa sales office or the nearest
Yaskawa representative.
Yaskawa AC Drive-V1000
Technical Manual
STOP
(Hz)
(Hz)
(A)
(V)
:
:
:
:
:
:
:
:
:
:
V1000
周波数指令
正転逆転選択
出力周波数
出力電流
出力電圧
モニタ
ベリファイ
セットアップ
パラメータ設定
オートチューニング
据え付け、運転の前には必ず取扱説明書を読むこと。
通電中および電源遮断後
5
分以内はフロントカバーを
外さないこと。
400V
級インバータの場合は、電源の中性点が接地
されていることを確認すること。（ 対応）
けが．感電のおそれがあります。
危 険

1 Preface and Safety
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 5
◆Terms
Note: Indicates a supplement or precaution that does not cause drive damage.
Drive: Yaskawa AC Drive - V1000 Series
◆Registered Trademarks
Company names and product names listed in this manual are registered trademarks of those
companies.
◆Supplemental Safety Information
Read and understand this manual before installing, operating, or servicing this option. The
option must be installed according to this manual and local codes.
The following conventions are used to indicate safety messages in this manual. Failure to
heed these messages could result in serious or possibly even fatal injury or damage to the
products or to related equipment and systems.
DANGER
Indicates a hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION
Indicates a hazardous situation, which, if not avoided, could result in minor or
moderate injury.

1 Preface and Safety
6YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
■General Safety
NOTICE
Indicates an equipment damage message.
General Precautions
• The diagrams in this section may include options and drives without covers or safety shields to
illustrate details. Be sure to reinstall covers or shields before operating any devices. The option board
should be used according to the instructions described in this manual.
• Any illustrations, photographs, or examples used in this manual are provided as examples only and
may not apply to all products to which this manual is applicable.
• The products and specifications described in this manual or the content and presentation of the
manual may be changed without notice to improve the product and/or the manual.
• When ordering a new copy of the manual due to damage or loss, contact your Yaskawa
representative or the nearest Yaskawa sales office and provide the manual number shown on the
front cover.
DANGER
Heed the safety messages in this manual.
Failure to comply will result in death or serious injury.
The operating company is responsible for any injuries or equipment damage resulting
from failure to heed the warnings in this manual.
NOTICE
Do not expose the drive to halogen group disinfectants.
Failure to comply may cause damage to the electrical components in the option.
Do not pack the drive in wooden materials that have been fumigated or sterilized.
Do not sterilize the entire package after the product is packed.

YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 7
2 Product Overview
2 Product Overview
◆About this Product
The 24 V Power Supply Option maintains drive control circuit power in the event of a main
power outage. The control circuit keeps the network communications and I/O data
operational in the event of a power outage. It supplies external power to the control circuit
only, and does not provide power to the main circuit of the drive.
It is possible to read fault and parameter data in the drive via the LED operator or network
communications when the drive switches to the 24 V Power Supply Option as a back-up
power supply.
◆Applicable Models
The 24 V Power Supply Option can be used with the drive models in Table 1 depending on
drive model.
Table 1 24 V Power Supply Options and Applicable Drive Models
24 V Power Supply Option
Part Number Applicable Drive Model Number
PS-V10S
Single-Phase 200 V Class CIMR-VBA0001 to 0018
Three-Phase 200 V Class CIMR-V2A0001 to 0020
Three-Phase 400 V Class CIMR-V4A0001 to 0011
PS-V10M Three-Phase 200 V Class CIMR-V2A0030 to 0069
Three-Phase 400 V Class CIMR-V4A0018 to 0038

8 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
3 Receiving
3 Receiving
Perform the following tasks after receiving this product:
• Inspect the option for damage.
If the option appears damaged upon receipt, contact the shipper immediately.
• Verify receipt of the correct model by checking the model number.
• If you have received the wrong model or this product does not function properly, contact
your supplier.
◆Nameplate
Figure 1
Figure 1 Nameplate (PS-V10S)
MASS : 0.1kg
PS - V10S
:
: EUS610010
: DC24V ±20% / 0.41A /10W
: 8W
:
:
: E131457
MODEL
CODE
APPLICABLE INVERTER
INPUT
OUTPUT
O/N
S/N
FILE NO
Use UL Listed Class 2 power source only.
: V1000
PASS
Option Model Code
Input Specification
Output Specification
Lot Number
Serial Number
YASKAWA ELECTRIC CORPORATION
2-1 Kurosaki-shiroishi, Yahatanishi-Ku, Kitakyushu 806-0004 Japan
MADE IN JAPAN
IND.CONT.EQ.
7J48

3 Receiving
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 9
◆Contents and Packaging
Table 2 Contents of Package
◆Additional Parts Required for UL and CE Compliance
An additional mounting support bracket is required for UL and CE compliance in some
cases. Refer to Table 3. Refer to UL and CE Compliance on page 15 for instructions on
installing the mounting support bracket. For questions or ordering information contact your
sales representative or Yaskawa.
Table 3 Types of Mounting Support Brackets (not included)
Description: 24 V Power Supply
Option
Option Connection
Cable <1>
<1> Option Connection Cables differ depending on drive model. Black cable connectors are supplied with the PS-
V10S 24 V Power Supply Option. White cable connectors are supplied with the PS-V10M 24 V Power Supply
Option.
Installation Manual
-
Quantity: 111
EZZ020639A EZZ020639B EZZ020639C
MANUAL

3 Receiving
10 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
◆Tool Requirements
Screwdriver (flat-tip): A straight-edge screwdriver with a blade width of 2.5 mm (3/32 in.)
and a blade thickness of 0.6 mm (1/64 in.) is required to install the 24 V Power Supply
Option.
Figure 2
Figure 2 Required Screwdriver Dimensions
Blade width
2.5 mm max.
0.6 mm max.
Blade thickness

YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 11
4 24 V Power Supply Option Components
4 24 V Power Supply Option Components
◆24 V Power Supply Option
Figure 3
Figure 3 24 V Power Supply Option
◆Power Supply Plug
Table 4 Plug Connector Terminals
A – Option Cover D – Mounting Attachment
B – Power supply display LED E – Black socket (to drive power board)
C – Plug connector
(24 V power supply input)
F – White socket (to drive controller)
Terminal
Designation Description
24 +24 V
00V
FE Ground
Inside the Option Cover
E
F
C
24 V Power Supply Option Components
D
B
A
Plug Connector

12 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
5 Installation Procedure
5 Installation Procedure
◆Section Safety
DANGER
Electrical Shock Hazard
Do not connect or disconnect wiring while the power is on.
Failure to comply will result in death or serious injury.
Disconnect all power to the drive, wait at least five minutes after all indicators are off,
measure the DC bus voltage to confirm safe level, and check for unsafe voltages before
servicing to prevent electric shock. The internal capacitor remains charged even after the
24 V power supply is turned off. The charge indicator LED will extinguish when the DC
bus voltage is below 50 Vdc.
WARNING
Electrical Shock Hazard
Do not remove option board cover while the power is on.
Failure to comply could result in death or serious injury.
The diagrams in this section may include options and drives without covers or safety
shields to show details. Be sure to reinstall covers or shields before operating any devices.
The option board should be used according to the instructions described in this manual.
Do not allow unqualified personnel to use equipment.
Failure to comply could result in death or serious injury.
Maintenance, inspection, and replacement of parts must be performed only by authorized
personnel familiar with installation, adjustment, and maintenance of this product.

5 Installation Procedure
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 13
Do not use damaged wires, place excessive stress on wiring, or damage the wire
insulation.
Failure to comply could result in death or serious injury.
Fire Hazard
Tighten all terminal screws to the specified tightening torque.
Loose electrical connections could result in death or serious injury by fire due to
overheating of electrical connections.
NOTICE
Observe proper electrostatic discharge procedures (ESD) when handling the option,
drive, and circuit boards.
Failure to comply may result in ESD damage to circuitry.
Never shut the power off while the drive is outputting voltage.
Failure to comply may cause the application to operate incorrectly or damage the drive.
Do not operate damaged equipment.
Failure to comply may cause further damage to the equipment.
Do not connect or operate any equipment with visible damage or missing parts.
Do not use unshielded cable for control wiring.
Failure to comply may cause electrical interference resulting in poor system performance.
Use shielded twisted-pair wires and ground the shield to the ground terminal of the drive.
Properly connect all pins and connectors.
Failure to comply may prevent proper operation and possibly damage equipment.
Check wiring to ensure that all connections are correct after installing the option
and connecting any other devices.
Failure to comply may result in damage to the option.
WARNING

5 Installation Procedure
14 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
◆Single Drive Installation
To maintain sufficient space for airflow and wiring with the 24 V Power Supply Option
installed, refer to Figure 4.
Figure 4
Figure 4 Correct Installation Spacing
Note: 1. IP20/NEMA Type 1 and IP20/Open-Chassis models require the same amount of space above and below
the drive for installation.
2. Yaskawa recommends unmounting the drive to simplify installation of the 24 V Power Supply Option.
◆Wiring Diagram
Figure 5 illustrates the 24 V Power Supply Option and drive interconnections.
Figure 5
Figure 5 Connection Diagram for Drive and 24 V Power Supply Option.
A – 30 mm minimum
AA
R/L1
T/L3
S/L2
U/T1
V/T2
W/T3
Motor
AC input Drive
＋
−
FE
24 V
0 V
24 V Power
Supply Option
24 V Power
Supply Input CN3-2
CN3-1
CN3 (Controller PCB)
CN3 (Power PCB)
Black
socket
Note 2: This cable with “black” connector ends
is supplied with the PS-V10S Option
Note 1: This cable with “white” connector ends
is supplied with the PS-V10M Option
To Controller
To Pwr Board
Note:2
Note:1

5 Installation Procedure
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 15
◆UL and CE Compliance
■Installation Area
Note: This product must be used in areas with an environment rating no greater than Pollution Degree
2 according to UL standard.
■External Power Supply
Use Class 2 power supply as defined by UL standard.
■Mounting Support Bracket
The mounting support bracket listed below is required for compliance with UL and CE
(Type 1) regulations. If these supports are not used, the design is considered “Open Type.”
Table 5 Applicable Mounting Support Brackets by Drive Model
Voltage Class Model CIMR-VPower Supply Option Bracket
Single-Phase
200 V Class
BA0001B
PS-V10S
EZZ020639ABA0002B
BA0003B
BA0006B
EZZ020639B
BA0010B
BA0012B
BA0018B
Three-Phase
200 V Class
2A0001B
PS-V10S
EZZ020639A2A0002B
2A0004B
2A0006B
EZZ020639B
2A0008B
2A0010B
2A0012B
2A0018B
2A0020B
2A0030F
PS-V10M
2A0040F
2A0056F
EZZ020639C
2A0069F

5 Installation Procedure
16 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
Mounting Support Bracket Installation
After properly installing the option card, fasten the mounting support brackets (not
provided) using the screws included in the support bracket packaging as shown in the figure
below.
Refer to Dimensions on page 30 for screw hole alignment. Make sure the supports are
properly located relative to the height and positioning the drive.
Figure 6
Figure 6 Proper Installation of the Mounting Support Bracket
Three-Phase
400 V Class
4A0001B
PS-V10S
EZZ020639A
4A0002B
4A0004B
EZZ020639B
4A0005B
4A0007B
4A0009B
4A0011B
4A0018F
PS-V10M
4A0023F
4A0031F
4A0038FEZZ020639C
Voltage Class Model CIMR-VPower Supply Option Bracket
Drive with PS-V10S Drive with PS-V10M

5 Installation Procedure
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 17
◆Separate the 24 V Power Supply Option Cover and Mounting
Attachment
DANGER! Electrical Shock Hazard. Disconnect all power to the drive, before servicing. Failure to comply
will result in death or serious injury. Wait at least five minutes after all indicators are off. The drive has
internal capacitors that remain charged even after the Power Supply is disconnected. The drive charge LED
will extinguish when the DC bus voltage is below 50Vdc. Measure drive DC bus voltage to confirm safe
level.
The 24 V Power Supply Option cover must be separated from its mounting attachment to
allow access to option connection sockets prior to installation.
1. Insert a flat-blade screwdriver into two small slots on the side of the 24 V Power Supply
Option cover to lift the cover off its mounting attachment as shown on Figure 7.
Figure 7
Figure 7 Removing the 24 V Power Supply Option Cover to Expose Connection Sockets
2. Separate the 24 V Power Supply Option cover from its mounting attachment.

5 Installation Procedure
18 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
◆Remove the Drives Cable Access Cover
The drive cable-access cover must be removed to allow access to drive connection sockets
prior to mounting the option to the drive.
1. Insert a flat-blade screwdriver blade into one of the slots on the drives cable-access cover
and gently pry up to loosen and remove the cover as shown in Figure 8.
Note: The cable access cover piece may be discarded.
Figure 8
Figure 8 Removing the Cable-access Cover on the Drive

5 Installation Procedure
YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual 19
◆Unplug Drive Cables to Install the 24 V Power Supply Option
(PS-V10S)
If you are installing 24 V Power Supply Option (PS-V10M), proceed to Unplug Drive
Cables to Install the 24 V Power Supply Option (PS-V10M) on page 20.
1. Unplug one end of the existing drive cable from its socket inside the drive as shown in
Figure 9. Press inward on the cable release tab in the center of the cable connector and
use a flat-blade screwdriver to gently pry up to remove the connector from its socket.
NOTICE: Do not use excessive force when using a screwdriver to free the drive cable connection. Failure to
comply may damage or break the cable connectors.
Figure 9
Figure 9 Unplugging the Drive Cable Connection (PS-V10S)
2. Next, plug the supplied 24 V Power Supply Option connection cable into the drive cable
socket and click firmly into position as shown in Figure 10.
Note: Refer to Table 1 to verify the correct option part number is used with your drive model.
Connection cables and mounting attachments for 24 V Power Supply Options differ depending
on drive model.
Figure 10
Figure 10 Plugging the Option Connection Cable into the Drive (PS-V10S)
Insert screwdriver into
these two locations to free cable

5 Installation Procedure
20 YASKAWA ELECTRIC TOBP C730600 27B V1000 Option PS-V10 Installation Manual
◆Unplug Drive Cables to Install the 24 V Power Supply Option
(PS-V10M)
1. Unplug one end of the existing drive cable from its socket inside the drive as shown in
Figure 11. Press inward on the cable release tab in the center of the cable connector and
use a flat-blade screwdriver to gently pry down to remove the connector from its socket.
NOTICE: Do not use excessive force when using a screwdriver to free the drive cable connection. Failure to
comply may damage or break the cable connectors.
Figure 11
Figure 11 Unplugging the Drive Cable Connection (PS-V10M)
2. Next, plug the supplied 24 V Power Supply Option connection cable into the drive cable
socket and click firmly into position as shown in Figure 12.
Note: Refer to Tab le 1 to verify the correct option part number is used with your drive model.
Connection cables and mounting attachments for 24 V Power Supply Options differ depending
on drive model.
Figure 12
Figure 12 Plugging the Option Connection Cable into the Drive (PS-V10M)