YASKAWA MOTOMAN-VA1400 User manual

MANUAL NO.
5
HW0484963
Part Number: 155556-1CD
Revision: 3
MOTOMAN-VA1400
INSTRUCTIONS
TYPE:
YR-VA01400-A00 (STANDARD SPECIFICATION)
YR-VA01400-A01 (SLU-AXES WITH LIMIT SWITCHES)
YR-VA01400-A10 (CEILING-MOUNTED SPECIFICATION)
YR-VA01400-A11 (CEILING-MOUNTED, SLU-AXES WITH
LIMIT SWITCHES)
Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain
for future reference.
MOTOMAN INSTRUCTIONS
MOTOMAN-VA1400 INSTRUCTIONS
DX100 INSTRUCTIONS
DX100 OPERATOR’S MANUAL
DX100 MAINTENANCE MANUAL
The DX100 operator’s manual above corresponds to specific usage.
Be sure to use the appropriate manual.
1 of 85

ii
155556-1CD
HW0484963
VA1400
Copyright © 2017, 2012 Yaskawa America, Inc.
Terms of Use and Copyright Notice
All rights reserved. This manual is freely available as a service to Yaskawa
customers to assist in the operation of Motoman robots, related equipment
and software This manual is copyrighted property of Yaskawa and may
not be sold or redistributed in any way. You are welcome to copy this
document to your computer or mobile device for easy access but you may
not copy the PDF files to another website, blog, cloud storage site or any
other means of storing or distributing online content.
Printed in the United States of America
First Printing, 2012
Yaskawa America, Inc.
Motoman Robotics Division
100 Automation Way
Miamisburg, OH 45342
Phone: [phone]
www.motoman.com
2 of 85

iii
155556-1CD
HW0484963
VA1400
MANDATORY
• This instruction manual is intended to explain mainly on the
mechanical part of the MOTOMAN-VA1400 for the application to the
actual operation and for proper maintenance and inspection. It
describes on safety and handling, details on specifications,
necessary items on maintenance and inspection, to explain
operating instructions and maintenance procedures. Be sure to
read and understand this instruction manual thoroughly before
installing and operating the manipulator.
• General items related to safety are listed in Chapter 1: Safety of the
DX100 Instructions. To ensure correct and safe operation, carefully
read the DX100 Instructions before reading this manual.
CAUTION
• Some drawings in this manual are shown with the protective covers
or shields removed for clarity. Be sure all covers and shields are
replaced before operating this product.
• The drawings and photos in this manual are representative
examples and differences may exist between them and the
delivered product.
• YASKAWA may modify this model without notice when necessary
due to product improvements, modifications, or changes in
specifications.
• If such modification is made, the manual number will also be
revised.
• If your copy of the manual is damaged or lost, contact a YASKAWA
representative to order a new copy. The representatives are listed
on the back cover. Be sure to tell the representative the manual
number listed on the front cover.
• YASKAWA is not responsible for incidents arising from unauthorized
modification of its products. Unauthorized modification voids your
product's warranty.
3 of 85

iv
155556-1CD
HW0484963
VA1400
We suggest that you obtain and review a copy of the ANSI/RIA National
Safety Standard for Industrial Robots and Robot Systems (ANSI/RIA
R15.06-2012). You can obtain this document from the Robotic Industries
Association (RIA) at the following address:
Robotic Industries Association
900 Victors Way
P.O. Box 3724
Ann Arbor, Michigan 48106
TEL: [phone]
FAX: [phone]
www.roboticsonline.com
Ultimately, well-trained personnel are the best safeguard against
accidents and damage that can result from improper operation of the
equipment. The customer is responsible for providing adequately trained
personnel to operate, program, and maintain the equipment. NEVER
ALLOW UNTRAINED PERSONNEL TO OPERATE, PROGRAM, OR
REPAIR THE EQUIPMENT!
We recommend approved Yaskawa training courses for all personnel
involved with the operation, programming, or repair of the equipment.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
4 of 85

v
155556-1CD
HW0484963
VA1400 Notes for Safe Operation
Notes for Safe Operation
Read this manual carefully before installation, operation, maintenance, or
inspection of the MOTOMAN-VA1400.
In this manual, the Notes for Safe Operation are classified as “DANGER”,
“WARNING”, “CAUTION”, “MANDATORY”, or “PROHIBITED.”
Even items described as “CAUTION” may result in a serious accident in
some situations.
At any rate, be sure to follow these important items.
DANGER
Indicates an imminent hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury to
personnel and damage to equipment.
It may also be used to alert against
unsafe practices.
MANDATORY
Always be sure to follow explicitly the
items listed under this heading.
PROHIBITED
Must never be performed.
NOTE
To ensure safe and efficient operation at all times, be sure to
follow all instructions, even if not designated as “DANGER”,
“CAUTION” and “WARNING.”
DANGER
• Maintenance and inspection must be performed by specified
personnel.
Failure to observe this caution may result in electric shock or injury.
• For disassembly or repair, contact your YASKAWA representative.
• Do not remove the motor, and do not release the brake.
Failure to observe these safety precautions may result in death or
serious injury from unexpected turning of the manipulator's arm.
5 of 85

Notes for Safe Operation
vi
155556-1CD
HW0484963
VA1400
WARNING
• Before operating the manipulator, check that servo power is turned
OFF pressing the emergency stop buttons on the front door of the
DX100 and the programming pendant.
When the servo power is turned OFF, the SERVO ON LED on the
programming pendant is turned OFF.
Injury or damage to machinery may result if the emergency stop circuit
cannot stop the manipulator during an emergency. The manipulator
should not be used if the emergency stop buttons do not function.
Figure 1: Emergency Stop Button
• Once the emergency stop button is released, clear the cell of all
items which could interfere with the operation of the manipulator.
Then turn the servo power ON.
Injury may result from unintentional or unexpected manipulator motion.
Figure 2: Release of Emergency Stop
TURN
• Observe the following precautions when performing teaching
operations within the P-point maximum envelope of the
manipulator:
– Be sure to use a lockout device to the safeguarding when going
inside. Also, display the sign that the operation is being
performed inside the safeguarding and make sure no one closes
the safeguarding.
– View the manipulator from the front whenever possible.
– Always follow the predetermined operating procedure.
– Keep in mind the emergency response measures against the
manipulator’s unexpected motion toward you.
– Ensure that you have a safe place to retreat in case of
emergency.
Improper or unintended manipulator operation may result in injury.
• Confirm that no person is present in the P-point maximum envelope
of the manipulator and that you are in a safe location before:
– Turning ON the power for the DX100.
– Moving the manipulator with the programming pendant.
– Running the system in the check mode.
– Performing automatic operations.
Injury may result if anyone enters the P-point maximum envelope of the
manipulator during operation. Always press an emergency stop button
immediately if there is a problem.
The emergency stop buttons are located on the right of front door of the
DX100 and the programming pendant.
6 of 85

vii
155556-1CD
HW0484963
VA1400 Definition of Terms Used In this Manual
Definition of Terms Used In this Manual
The MOTOMAN is the YASKAWA industrial robot product.
The MOTOMAN usually consists of the manipulator, the controller, the
programming pendant, and supply cables.
In this manual, the equipment is designated as follows:
Registered Trademark
In this manual, names of companies, corporations, or products are
trademarks, registered trademarks, or brand names for each company or
corporation. The indications of (R) and TM are omitted.
CAUTION
• Perform the following inspection procedures prior to conducting
manipulator teaching. If problems are found, repair them
immediately, and be sure that all other necessary processing has
been performed.
– Check for problems in manipulator movement.
– Check for damage to insulation and sheathing of external wires.
• Always return the programming pendant to the hook on the cabinet
of the DX100 after use.
The programming pendant can be damaged if it is left in the
manipulator's work area, on the floor, or near fixtures.
• Read and understand the Explanation of Warning Labels in the
DX100 Instructions before operating the manipulator:
Equipment Manual Designation
DX100 controller DX100
DX100 programming pendant Programming pendant
Cable between the manipulator and the
controller
Manipulator cable
7 of 85

Explanation of Warning Labels
viii
155556-1CD
HW0484963
VA1400
Explanation of Warning Labels
The following warning labels are attached to the manipulator.
Always follow the warnings on the labels.
Also, an identification label with important information is placed on the
body of the manipulator. Prior to operating the manipulator, confirm the
contents.
Figure 3: Warning Label Locations
WARNING
Do not enter
robot
work area.
WARNING
Moving parts
may cause
injury
Nameplate:
WARNING Label B:
WARNING Label A:
WARNING Label B
Nameplate
WARNING Label A
WARNING Label A
8 of 85

ix
155556-1CD
HW0484963
VA1400 Safeguarding Tips
Safeguarding Tips
All operators, programmers, maintenance personnel, supervisors, and
anyone working near the system must become familiar with the operation
of this equipment. All personnel involved with the operation of the
equipment must understand potential dangers of operation. General
safeguarding tips are as follows:
• Improper operation can result in personal injury and/or damage to
the equipment. Only trained personnel familiar with the operation of
this equipment, the operator's manuals, the system equipment, and
options and accessories should be permitted to operate this
equipment.
• Improper connections can damage the equipment. All connections
must be made within the standard voltage and current ratings of the
equipment.
• The system must be placed in Emergency Stop (E-Stop) mode
whenever it is not in use.
• In accordance with ANSI/RIA R15.06-2012, section 4.2.5, Sources of
Energy, use lockout/tagout procedures during equipment
maintenance. Refer also to Section 1910.147 (29CFR, Part 1910),
Occupational Safety and Health Standards for General Industry
(OSHA).
Mechanical Safety Devices
The safe operation of this equipment is ultimately the users responsibility.
The conditions under which the equipment will be operated safely should
be reviewed by the user. The user must be aware of the various national
codes, ANSI/RIA R15.06-2012 safety standards, and other local codes
that may pertain to the installation and use of this equipment.
Additional safety measures for personnel and equipment may be required
depending on system installation, operation, and/or location. The following
safety equipment is provided as standard:
• Safety barriers
• Door interlocks
• Emergency stop palm buttons located on operator station
Check all safety equipment frequently for proper operation. Repair or
replace any non-functioning safety equipment immediately.
9 of 85

Programming, Operation, and Maintenance Safety
x
155556-1CD
HW0484963
VA1400
Programming, Operation, and Maintenance Safety
All operators, programmers, maintenance personnel, supervisors, and
anyone working near the system must become familiar with the operation
of this equipment. Improper operation can result in personal injury and/or
damage to the equipment. Only trained personnel familiar with the
operation, manuals, electrical design, and equipment interconnections of
this equipment should be permitted to program, or maintain the system.
All personnel involved with the operation of the equipment must
understand potential dangers of operation.
• Inspect the equipment to be sure no potentially hazardous conditions
exist. Be sure the area is clean and free of water, oil, debris, etc.
• Be sure that all safeguards are in place. Check all safety equipment
for proper operation. Repair or replace any non-functioning safety
equipment immediately.
• Check the E-Stop button on the operator station for proper operation
before programming. The equipment must be placed in Emergency
Stop (E-Stop) mode whenever it is not in use.
• Back up all programs and jobs onto suitable media before program
changes are made. To avoid loss of information, programs, or jobs, a
backup must always be made before any service procedures are
done and before any changes are made to options, accessories, or
equipment.
• Any modifications to the controller unit can cause severe personal
injury or death, as well as damage to the robot! Do not make any
modifications to the controller unit. Making any changes without the
written permission from Yaskawa will void the warranty.
• Some operations require standard passwords and some require
special passwords.
• The equipment allows modifications of the software for maximum
performance. Care must be taken when making these modifications.
All modifications made to the software will change the way the
equipment operates and can cause severe personal injury or death,
as well as damage parts of the system. Double check all
modifications under every mode of operation to ensure that the
changes have not created hazards or dangerous situations.
• This equipment has multiple sources of electrical supply. Electrical
interconnections are made between the controller and other
equipment. Disconnect and lockout/tagout all electrical circuits
before making any modifications or connections.
• Do not perform any maintenance procedures before reading and
understanding the proper procedures in the appropriate manual.
• Use proper replacement parts.
• Improper connections can damage the equipment. All connections
must be made within the standard voltage and current ratings of the
equipment.
10 of 85

xi
155556-1CD
HW0484963
VA1400 Maintenance Safety
Maintenance Safety
Turn the power OFF and disconnect and lockout/tagout all electrical
circuits before making any modifications or connections.
Perform only the maintenance described in this manual. Maintenance
other than specified in this manual should be performed only by Yaskawa-
trained, qualified personnel.
Summary of Warning Information
This manual is provided to help users establish safe conditions for
operating the equipment. Specific considerations and precautions are also
described in the manual, but appear in the form of Dangers, Warnings,
Cautions, and Notes.
It is important that users operate the equipment in accordance with this
instruction manual and any additional information which may be provided
by Yaskawa. Address any questions regarding the safe and proper
operation of the equipment to Yaskawa Customer Support.
11 of 85

Customer Support Information
xii
155556-1CD
HW0484963
VA1400
Customer Support Information
If you need assistance with any aspect of your VA1400 system, please
contact YASKAWA Customer Support at the following 24-hour telephone
number:
For routine technical inquiries, you can also contact YASKAWA Customer
Support at the following e-mail address:
When using e-mail to contact YASKAWA Customer Support, please
provide a detailed description of your issue, along with complete contact
information. Please allow approximately 24 to 36 hours for a response to
your inquiry.
Please have the following information ready before you call Customer
Support:
[email protected]
NOTE
Please use e-mail for routine inquiries only. If you have an
urgent or emergency need for service, replacement parts,
or information, you must contact YASKAWA Customer
Support at the telephone number shown above.
• System VA1400
• Robots ___________________________
• Primary Application ___________________________
• Controller DX100
• Software Version Access this information on the
Programming Pendant’s LCD
display screen by selecting {MAIN
MENU} - {SYSTEM INFO} -
{VERSION}
• Robot Serial Number Located on the robot data plate
• Robot Sales Order Number Located on the DX100 controller
data plate
[phone]
12 of 85

xiii
155556-1CD
HW0484963
VA1400 Table of Contents
Table of Contents
1 Product Confirmation ...................................................................................................................... 1-1
1.1 Contents Confirmation ....................................................................................................... 1-1
1.2 Order Number Confirmation .............................................................................................. 1-2
2 Transport......................................................................................................................................... 2-1
2.1 Transport Method .............................................................................................................. 2-1
2.1.1 Using a Crane ...................................................................................................... 2-2
2.1.2 Using a Forklift...................................................................................................... 2-3
2.2 Shipping Bolts and Brackets.............................................................................................. 2-3
3 Installation....................................................................................................................................... 3-1
3.1 Safeguarding Installation ................................................................................................... 3-2
3.2 Mounting Procedures for Manipulator Base ...................................................................... 3-2
3.2.1 Mounting Example................................................................................................ 3-3
3.3 Types of Mounting ............................................................................................................. 3-4
3.3.1 S-Axis Operating Range....................................................................................... 3-4
3.3.2 Fixing the Manipulator Base ................................................................................. 3-4
3.3.3 Precautions to Prevent the Manipulator from Falling............................................ 3-4
3.4 Location ............................................................................................................................. 3-5
4 Wiring.............................................................................................................................................. 4-1
4.1 Grounding .......................................................................................................................... 4-1
4.2 Cable Connection .............................................................................................................. 4-2
4.2.1 Connection to the Manipulator.............................................................................. 4-2
4.2.2 Connection to the DX100 ..................................................................................... 4-2
5 Basic Specifications ........................................................................................................................ 5-1
5.1 Basic Specifications........................................................................................................... 5-1
5.2 Part Names and Working Axes.......................................................................................... 5-2
5.3 Manipulator Base Dimensions ........................................................................................... 5-2
5.4 Dimensions and P-Point Maximum Envelope.................................................................... 5-3
5.5 Alterable Operating Range ................................................................................................ 5-5
13 of 85

Table of Contents
xiv
155556-1CD
HW0484963
VA1400
6 Allowable Load for Wrist Axis and Wrist Flange ............................................................................. 6-1
6.1 Allowable Wrist Load ......................................................................................................... 6-1
6.2 Wrist Flange....................................................................................................................... 6-2
7 System Application.......................................................................................................................... 7-1
7.1 Peripheral Equipment Mounts............................................................................................ 7-1
7.1.1 Allowable Load ..................................................................................................... 7-1
7.1.2 Installation Position............................................................................................... 7-1
7.2 Internal User I/O Wiring Harness and Air Line................................................................... 7-3
8 Electrical Equipment Specification .................................................................................................. 8-1
8.1 Position of Limit Switch ...................................................................................................... 8-1
8.2 Internal Connections .......................................................................................................... 8-2
9 Maintenance and Inspection ........................................................................................................... 9-1
9.1 Inspection Schedule........................................................................................................... 9-1
9.2 Notes on Maintenance Procedures.................................................................................... 9-5
9.2.1 Battery Pack Replacement ................................................................................... 9-5
9.3 Notes on Grease Replenishment/Exchange Procedures .................................................. 9-7
9.3.1 Grease Replenishment/Exchange for S-Axis Speed Reducer ............................. 9-7
9.3.1.1 Grease Replenishment............................................................................ 9-8
9.3.1.2 Grease Exchange.................................................................................... 9-9
9.3.2 Grease Replenishment/Exchange for L-Axis Speed Reducer............................ 9-10
9.3.2.1 Grease Exchange.................................................................................. 9-10
9.3.2.2 Grease Exchange.................................................................................. 9-11
9.3.3 Grease Replenishment/Exchange for E-Axis Speed Reducer ........................... 9-12
9.3.3.1 Grease Replenishment.......................................................................... 9-12
9.3.3.2 Grease Exchange.................................................................................. 9-13
9.3.4 Grease Replenishment/Exchange for U-Axis Speed Reducer ........................... 9-14
9.3.4.1 Grease Replenishment.......................................................................... 9-14
9.3.4.2 Grease Exchange.................................................................................. 9-15
9.3.5 Grease Replenishment for R-Axis Speed Reducer ............................................ 9-16
9.3.6 Grease Replenishment for B-Axis Speed Reducer ............................................ 9-17
9.3.7 Grease Replenishment for T-Axis Gear.............................................................. 9-18
9.3.8 Grease Replenishment for R-Axis Gear ............................................................. 9-19
9.3.9 Notes for Maintenance........................................................................................ 9-20
9.3.9.1 Wrist Unit............................................................................................... 9-20
9.3.9.2 Battery Pack Connection ....................................................................... 9-21
14 of 85

xv
155556-1CD
HW0484963
VA1400 Table of Contents
10 Recommended Spare Parts........................................................................................................ 10-1
11 Parts List..................................................................................................................................... 11-1
11.1 S-Axis Unit ..................................................................................................................... 11-1
11.2 L-Axis Unit ..................................................................................................................... 11-4
11.3 U-Axis Unit..................................................................................................................... 11-5
11.4 E-Axis Unit ..................................................................................................................... 11-8
11.5 R-Axis Unit................................................................................................................... 11-10
11.6 Wrist Unit ..................................................................................................................... 11-13
15 of 85

1 Product Confirmation
1.1 Contents Confirmation
1-1
155556-1CD
HW0484963
VA1400
1 Product Confirmation
1.1 Contents Confirmation
Confirm the contents of the delivery when the product arrives.
Standard delivery includes the following four items (information for the
content of optional goods are given separately):
• Manipulator
• DX100
• Programming pendant
• Manipulator cables (between the DX100 and the Manipulator)
CAUTION
• Confirm that the manipulator and the DX100 have the same order
number. Special care must be taken when more than one
manipulator is to be installed.
If the numbers do not match, manipulators may not perform as
expected and cause injury or damage.
16 of 85

1-2
155556-1CD
HW0484963
VA1400 1 Product Confirmation
1.2 Order Number Confirmation
1.2 Order Number Confirmation
Check that the order number of the manipulator corresponds to the
DX100. The order number is located on a label as shown below.
Fig. 1-1: Location of Order Number Labels
THE MANIPULATOR AND THE CONTROLLER
SHOULD HAVE SAME ORDER NUMBER.
ORDER NO.
Check that the manipulator
and the DX100 have the
same order number.
Label (Enlarged View)
(b) Manipulator (Side View)(a) DX100 (Front View)
X81
PROGRAMMING PENDANT
Y
C
E
G
N
O
T
P
M
E
E
S
R
ON
TRIPPED
RESET
OFF
WARNING
Do not open the door
THE MANIPULATOR AND THE CONTROLLER
SHOULD HAVE SAME ORDER NUMBER.
AVERAGE
PEAK
kVA
kA
INTERRUPTCURRENT
ERDR-
POWERSUPPLY
TYPE
DX100
kVA
3PHASE
NJ2960-1
60Hz
SERIALNo.
DATE
AC220V
MADEIN JAPAN
50/60HzAC200V
ORDER NO.
NJ1529
17 of 85

2 Transport
2.1 Transport Method
2-1
155556-1CD
HW0484963
VA1400
2 Transport
2.1 Transport Method
CAUTION
• Sling applications and crane or forklift operations must be
performed by authorized personnel only.
Failure to observe this caution may result in injury or damage.
• Avoid excessive vibration or shock during transport.
The system consists of precision components. Failure to observe this
caution may adversely affect performance.
NOTE
• The weight of the manipulator is approximately 150 kg
including the shipping bolts and brackets. Use a wire rope
strong enough to withstand the weight.
• Mount the shipping bolts and brackets for transporting the
manipulator.
• Avoid putting external force on the arm or motor unit when
transporting by a crane, forklift, or other equipment.
Failure to observe this instruction may result in injury.
18 of 85

2-2
155556-1CD
HW0484963
VA1400 2 Transport
2.1 Transport Method
2.1.1 Using a Crane
As a rule, the manipulator should be lifted by a crane with two wire ropes
when removing it from the package and moving it. Be sure that the
manipulator is fixed with the shipping bolts and brackets before transport,
and lift it in the posture as shown in Fig. 2-1 “Transporting Position”.
Fig. 2-1: Transporting Position
Rubber plate 40(W) 30(H)
(thickness: 2 mm )
Rubber plate
Shipping bracket
Hexagon socket
head cap screw M8 (2 screws) Hexagon socket
head cap screw M10 (2 screws)
Shipping bracket
Shipping bracket
19 of 85

2 Transport
2.2 Shipping Bolts and Brackets
2-3
155556-1CD
HW0484963
VA1400
2.1.2 Using a Forklift
When using a forklift, the manipulator should be fixed on a pallet with
shipping bolts as shown in Fig. 2-2 “Using a Forklift”. Insert claws under
the pallet and lift it. The pallet must be strong enough to support the
manipulator. Transport the manipulator slowly with due caution in order to
avoid overturning or slippage.
Fig. 2-2: Using a Forklift
2.2 Shipping Bolts and Brackets
The manipulator is provided with shipping bolts and a shipping brackets.
(See Fig. 2-1 “Transporting Position”.)
Fig. 2-3: Shipping Bolts and Brackets
• The shipping bolts and bracket are painted yellow.
• The shipping bracket is to be fixed with the hexagon socket head cap
screws M10 (2 screws).
Bolt M16 (4 places)
Pallet
Forklift claw entries
NOTE
Before turning ON the power, check to be sure that the
shipping bolts and brackets are removed. The shipping
bolts and brackets then must be stored for future use, in the
event that the manipulator must be moved again.
Hexagon socket
head cap screw M8
(2 screws)
Shipping bracket
Hexagon socket
head cap screw M8
(2 screws)
Hexagon socket
head cap screw M10
(2 screws)
Front View Side View
20 of 85