YELLOWRIVER YR-P0354S User manual

LED PAR LIGHT
Model:YR-P0354S
(3WX54pcs RGBW)

Contents
Section 1.Getting Started
Unpacking
Safety Instruction
Section 2. Set Up
Installation
Controlling Board
Machine Connection
Section 3. troubleshooting
Troubleshooting
Section 4. Reference
Control Menu
DMX Protocol
Specification
Section 1.Getting Started
Unpacking
Safety Instruction
Unpacking
1pc Fixture
1/4pc AC Power Cable with Plug
1/4pc Signal Convertor Cable
1pc User Manual
Thanks for choosing our product. Carefully unpack the box and check the contents
to ensure that all parts are present and in good conditions. If anything damaged in
transit, notify the shipper immediately and keep the packing material for inspection.
Again, please save the carton and all packing materials. If a fixture must be
returned to manufacturer, it is important that the fixture be returned in the original
manufacturer box and packing.

Safety Instruction
Please conserve this manual as operation guidance. If you sell this product to
other user, please make sure that they also receive this user manual.
Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on the decal or rear
panel of the fixture.
If the fixture is intended to indoor use only. To prevent risk of fire or shock, do not
expose fixture to rain or moisture. Make sure there are no flammable, explosive
or corrosive materials surrounded in 10meters while operating.
The unit must be installed in a location with adequate ventilation, at least 5m
away from adjacent surfaces. Be sure that no ventilation slots are blocked.
Some fixture may carry high heat, do not aim at objective more than 2minutes.
Safe rope should be used to install machine. Bearing of safe rope should be
more than 3times of the machine weight.
Always disconnect from the power source before servicing or replacing
fuse/lamp and be sure to replace with same fuse/lamp size and type. Cut off
power before moving, repairing and cleaning the machine.
To avoid electric shock, all fixtures must be connected to circuits with a suitable
earth connection.
Always secure fixture using a safety chain and carrying handles.
Do not operate at ambient temperatures higher than 104℉(40℃).
In case of failure or mis-function occurred, stop using immediately. Never try to
repair the fixture by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical
assistance center. Buy the same spare parts/components from manufacturer
directly.
Make sure the power cable is never crimped or damaged.
Avoid direct eye exposure to the light source while it is on.
Do not power on and power off the fixture frequently
When use DMX controller, please make sure that there is no interference
sources(e.g. intercom, high frequency radio waves and radiation source)
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service, please contact
your local distribution or after-sale service center.
Section 2. Set Up
Installation
Controlling Board
Machine connection
Installation
This machine should be mounted through the screw holes of truss. Safety
rope is a must to fix fixture well. Make sure truss and safety rope have strong
load capacity to bear more than 3 times of machine weight .
This machine should be installed by qualified technician.
For your safe，please read this user manual carefully before turn on
the fixture. This machine should be operated by qualified engineer！

Controlling Board
Front display panel
1. LED Display Panel
2. Button
MENU
Switch menu function
UP
Scroll upwards
DOWN
Scroll downwards
ENTER
Confirm by pressing ENTER
3. DMX Signal Input
3 PIN XRL port for DMX512 signal input ( daisy chain);
4. DMX signal output
3 PIN XRL Port for DMX512 signal output ( daisy chain);
5. Power Input
AC power cable port input( daisy chain)
6. Power Output
AC power cable port output;( daisy chain)
Machine Connection
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR connector on the other
end.
A word on termination: DMX is a resilient communication protocol,
however errors still occasionally occur. Termination reduces signal errors, and therefore best
practices include use of a terninator in all circumstances. If you are experiencing problems with
erratic fixture behavior, especially over long signal cable runs, a terminator may help improve
performance.
To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt
resistor, and wire it between pins 2&3 of the last fixture. They are also readily available from
specialty retailers.

Master and slave: select one machine as master, press the menu to choose the
function you want. Press other machines’ address to be DMX state. Use signal
cable to connect machines one by one. Then slave machines will run the same as
master machine.
Use controller to control lot of machines: if all machines are set the same menu
data, or different menu data, after use signal cable to connect to controller, all
machines will be controlled by controller. (before connect to controller, all
machines should be in the same channel mode 5ch or 9ch).
ATTENTION:
Section 3. Troubleshooting
Problem
Probable Cause(s)
Remedy
No power to fixture
Check power cables
Primary fuse blown
Replace fuse
No response from
fixture when power
is applies
Secondary fuse
blown
Replace fuse
Controller not
connected
Connect controller
Incorrect
addressing of the
fixtures
Check address setting on fixture and controller
Bad data link
connection
Inspect cables and correct poor connections
and/or broken cables.
Conflict between
tracking and vector
control
Eliminate scene cross-fade on controller
Fixture resets but
does not respond
correctly to
controller(DMX
mode operation)
Data link not
terminated
Insert termination plug in output of last fixture
Defective fixture or
2 devices
transmitting on link
Bypass fixtures one at a time until normal
operation is regained: unplug both connectors
and connect them directly together
Colors cannot be
mixed
Random color
mixing is on
Turn off random color mixing
Fixture does not
reset correctly
Electronic or
mechanical failure
Contact service technician
Lamp missing or
blown
Disconnect fixture and replace lamp
No light, lamp cuts
out intermittently, or
burns out too
quickly
Fixture or lamp is
too hot
Allow fixture to cool. If problem persists,
contact service technician
Section 4. Reference
Control Menu
DMX Protocol
Specification
Control Menu
No.
Menu
Function Specification（Press” ENTER”）
1
R---
r000 to r255 : from dark to bright
2
G— —
g000 to g255: from dark to bright
3
B---
b000 to b255: from dark to bright
4
N---
n000 to n255: from dark to bright
The 4 color’s
different
brightness
can mix out
all kinds of
color
5
C---
C000 to C255：7 color shade speed，from
slow to fast
6
J---
J000 to J255：7 color skip speed，from
slow to fast。
Maximum 8PCS fixtures connected by Daisy chain connection.

7
FS---
FS00 to FS09：choose flashing color
8
F---
F000 to F255：flash speed，from slow
to fast
9
LS---
LS00 to LS09：choose color
10
L---
L000 to L255：7 color from dark to bright
11
U---
U00 to U255 ：sound active speed, from
slow to fast
12
A— —
A000 to A255：auto speed, from slow to
fast
13
D9CH
DMX 9 channel mode, should connect
with DMX controller
14
D5CH
DMX 5 channel mode, should connect
with DMX controller
DMX protocol
DMX512 Channel Chart：（5CH）
CH
Function
Specification
CH1
Dimmer
R G B W color from dark to bright
CH2
R dimmer
Red color from dark to bright
CH3
G dimmer
Green color from dark to bright
CH4
B dimmer
Blue color from dark to bright
CH5
W dimmer
White color from dark to bright
DMX512 Channel Chart：（9CH）
CH
Function
Specification
CH1
Dimmer
R G B W color from dark to bright
CH2
R dimmer
Red color from dark to bright
CH3
G dimmer
Green color from dark to bright
CH4
B dimmer
Blue color from dark to bright
CH5
W dimmer
White color from dark to bright
CH6
Strobe
7 color flash speed, from slow to fast
CH7
Color mix
Seven color mix
CH8
Auto
0-60: shade ；61-120: skip ；121-180:
shade+skip ；181-240: flash by sound ；
241-255: skip by sound
CH 9
Auto Speed
DMX8 Channel auto speed & sound
volume adjust(from slow to fast)
Specification
Voltage：AC110V-240V
Frequency：50/60Hz
Machine Power：180W
LED power：3W
LED QTY：54pcs（R12 G14 B14 W14）
Beam Angle：30°
Control Mode：DMX512/Auto/Manual/Sound Active
Channel：9/ 5CH（switchable）
Indoor: IP20
Net weight:2.8kg
Size:26*26*11.5cm(excluding the bracket)

本公司有权对此份产品说明书进行修改，恕不另行通知。
Our company reserve right to revise this user manual without notice!
Innovation | Efficiency | Dedication | Harmonious