Yetter 2967-115A User manual

2967-115A
RESIDUE MANAGER ATTACHMENT
FOR
2960 SERIES II UNIT MOUNTED
CONSERVATION COULTER
2565-327_REV_D 06/2021
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: [e-mail]

2
FOREWORD
You’ve just joined an exclusive but rapidly
growing club.
For our part, we want to welcome you to the
group and thank you for buying a Yetter product.
We hope your new Yetter products will help you
achieve both goals-increase your productivity
and increase your efficiency so that you may
generate more profit.
This operator’s manual has been designed into
four major sections: Foreword, Safety
Precautions, Installation Instructions and Parts
Breakdown.
This SAFETY ALERT SYMBOL
indicatesimportantsafetymessagesin
the manual. When you see this
symbol, be alert to the possibility of
PERSONAL INJURY and carefully read the
message that follows.
The word NOTE is used to convey information
that is out of context with the manual text. It
contains special information such as
specifications, techniques and reference
information of a supplementary nature.
The word IMPORTANT is used in the text when
immediate damage willoccurtothemachinedue
to improper technique or operation. Important
willapply to the same informationasspecified by
note only of an immediate and urgent nature.
It is the responsibility of the user to read the
operator’s manual and comply with the safe and
correct operating procedure and to lubricate and
maintain the product according to the
maintenance schedule in the operator’s manual.
The user is responsible for inspecting his
machine and for having parts repaired or
replaced when continued use of the product
would cause damage or excessive wear to the
other parts.
It is the user’s responsibility to deliver his
machine to the Yetter dealer who sold him the
product for service or replacement of defective
parts, which are covered by the warranty policy.
If you are unable to understand or follow the
instructions provided in this publication, consult
your local Yetter dealer or contact:
YETTER MANUFACTURING CO.
309/776-4111
800/447-5777
309/776-3222 (FAX)
Website: www.yetterco.com
E-mail: [e-mail]
WARRANTY
Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being
expressly limited to replacement at the factoryof such parts or products as shall appear to be defective after inspection. This
warrantydoes not obligate the Companyto bear cost of labor in replacement of parts. It isthe policyof theCompanyto make
improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to be
made, other than herein set forth. This warranty is in effect for one year after purchase.
Dealer ___________________________________________________
Yetter Manufacturing warrants its own products only and cannot be responsible for damagestoequipment onwhich
mounted.

3
SAFETY
A brief description of signal words that may be used in this manual:
CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.
WARNING: Denotes a specific potential hazard.
DANGER: Denotes the most serious specific potential hazard.
SAFETY PRECAUTIONS
You can make your farm a safer place to live and work if you observe the safety
precautions given. Study these precautions carefully and insist that they be followed by those working with you and for you.
Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.
WARNING
Never clean, lubricate or adjust a machine that is in motion. Always lower or
block the implement before performing service.
If machine must be services in the raised position, jack or block it up to prevent it from accidentally falling and injuring
someone.
Do not allow riders on the tractor or implement.
Use speeds and caution dictated bythe terrain being traversed. Do not operate on any slope steep enough tocausetipping or
loss of control.
Be sure all personnel are clear of the immediate area before operating.
Read and understand the operator’s manual and require all other persons who will operate the equipment to do the same.
Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in an emergency.
CAUTION
Consult your implement and tractor operator’s manual for correct and safe
operating practices.
Beware of towed implement width and allow safe clearance.
FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

4
OPERATION PRECAUTIONS
STOP
Read this before using the Yetter product.
-MACHINE OPERATION
IMPORTANT: failure to properly set the planter frame height and levelness can
result in less than successful operation of the planter and the Yetter product and
may result in damaged equipment. All operators should read and thoroughly
understand the instructions given prior to using the Yetter product.
NOTE: DO NOT use this product if the planter is not adjusted properly!
Leveling the planter:
With the planter lowered to proper operating height (Usually 20”-22”). Read the
planter operator’s manual for recommended setting. Check to be sure the toolbar
and row unit parallel arms are level fore and aft. Re-check when the planter is in the
field and has been fully loaded with seed, fertilizer, granular chemicals, etc. Also, a
field check with a bubble level on the frame should be made of the hitch height to
ensure level operation front to back.
It is important for the planter to operate level laterally. Tire pressure must be
maintained at pressures specified by the manufacturer.
Field and actual planting conditions change and will dictate planter frame heights. You
must ensure that the row unit parallel arms are approximately parallel with the ground.
IMPORTANT: For proper operation of the planter attachments and row units, it is
imperative that the planter toolbars and row unit parallel arms be level side-to-side and
front-to-rear. The toolbar frame should operate at a 20”-22” height from the planting
surface. Check the manufacturer’s operator’s manual for instructions on how to adjust
the frame height and levelness.

5
PLANTER ADJUSTMENT

6
INSTALLATION
1. Remove the upper ½” x 2 ½” bolt which attaches the unit coulter arm to the bracket through the slot.
The two flat washers are no longer required. Save the lock nut for later use.
CAUTION: DO NOT USE SPACER STRAP ON COMBO ARM W.A. AS A
HANDLE, FINGERS MAY BE SERIOUSLY INJURED ON SHARP EDGE OF BLADE. USE
½” SQ. DRIVE SOCKET TOOLS TO ADJUST THIS PART.
2. Assemble the combo arm w.a. to the coulter with the ½” x 8” bolt, long spacer, short spacer and two flat
washers supplied. Use the ½” locknut removed in step 1. Tighten this bolt securely. The ½” x 8” bolt
must be through the TOP hole of the coulter arm.
3. Check the alignment of all holes in the combo arm and the adjustment plate with the combo adjustment
pin.
4. Attach the spoke wheels to the ends of the combo arm with the “D” bolts, hex nuts and lock washers.
Torque to 150 ft. lbs.

7
PARTS IDENTIFICATION
2967-115A-ST-FW

8
PARTS IDENTIFICATION
2966-140-ST-FW
2966-140-BW-FW

9
PARTS IDENTIFICATION
2966-141-FW

10
NOTES

11
NOTES

12
2565-327_REV_D 06/2021