York Millenium YK D Series User manual

MODELYK (STYLE D)
R-134a (COOLING ONLY)
WITH MICROCOMPUTER CONTROL CENTER
PART # 371-01200-010, 371-01200-011 & 371-01200-015
FOR ELECTRO-MECHANICAL STARTER,
SOLID STATE STARTER & VARIABLE SPEED DRIVE
WARNING
SYSTEM CONTAINS REFRIGERANT UNDER PRESSURE
SERIOUS INJURY COULD RESULT IF PROPER PROCEDURES ARE NOT
FOLLOWED WHEN SERVICING SYSTEM. ALL SERVICE WORK SHALL
BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN IN ACCOR-
DANCE WITH YORK INSTALLATION/OPERATION MANUAL.
INSTALLATION INSTRUCTIONS
MILLENNIUM
TM
CENTRIFUGAL LIQUID CHILLERS
Supersedes: See Back Form 160.52-N1 (1098)
28815A

2YORK INTERNATIONAL
ALLOWABLE COMPRESSOR/
COOLER/CONDENSER/MOTOR COMBINATIONS
NOMENCLATURE
YK CB CB G4 — CM D S Special Modifications
Model Design Level
Cooler Code Motor Code
Condenser Code Power Supply
– for 60 Hz
Compressor Code 5 for 50 Hz
COMPRESSOR COOLER CONDENSER MOTOR CODES
CODE CODE CODE 60 HZ 50 HZ
G4 CB, CC, CD, CE CB, CC, CD, DB, DC, DD CH – CT 5CE – 5CS
DD, DE CB, CC, CD, DB, DC, DD, EB, EC, ED
DB, DC, DD DB, DC, DD, EB, EC, ED
H0/H4 EC, ED DB, DC, DD, EB, EC, ED, FB, FC, FD CH – CV 5CE – 5CX
FC, FD EB, EC, ED, FB, FC, FD
EB EB, EC, ED, FB, FC, FD
H1/H5 FB, FC, FD EB, EC, ED, FB, FC, FD, GB, GC, GD CN – CY 5CK – 5DD
GC, GD FB, FC, FD, GB ,GC, GD
FB, FC FA, FB, FC, FD, GB, GC, GD
H2/H6 GB, GC, GD FA, FB, FC, FD, GB, GC, GD CN – CZ 5CK – 5DD
HB, HC GB, GC, GD
H3/H8 GB, GC, GD FB, FC, FD, GB, GC, GD CN – CZ (H8) 5CK – 5CU (H8)
HB, HC GB, GC, GD CN-CB (H3) 5CK – 5CX (H3)
GF, GH GB, GC, GD, HB, HC, HD
J1 HF, HH GB, GC, GD, HB, HC, HD, JB, JC, JD CW – DH 5CS – 5DH
J2 JF, JG, JH HB, HC, HD, JB, JC, JD
TF, TG, TH TB, TC, TD
HF, HH HB, HC, HD, JB, JC, JD DA – DJ 5DA – 5DH
JF, JG, JH HB, HC, HD, JB, JC, JD
J3 TF, TG, TH TB, TC, TD, VB, VC, VD
VF, VH TB, TC, TD, VB, VC, VD DA – DJ 5DA – 5DH
WF, WH VB, VC, VD
JF, JG, JH JB, JC, JD DA – DJ 5DA – 5DH
J4 TF, TG, TH TB, TC, TD, VB, VC, VD
VF, VH TB, TC, TD, VB, VC, VD DA – DJ 5DA - 5OJ
WF, WH VB, VC, VD

YORK INTERNATIONAL 3
FORM 160.52-N1
TABLE OF CONTENTS
DIMENSIONS................................................................................................ 5
CHILLER WEIGHTS ..................................................................................... 9
MOTOR WEIGHTS ....................................................................................... 13
INTRODUCTION........................................................................................... 14
General ................................................................................................. 14
Field Assembed Units Only ................................................................... 14
Shipment............................................................................................... 14
Inspection – Damage – Shortage....................................................... 15
Chiller Data Plate .................................................................................. 15
Rigging.................................................................................................. 15
Location ................................................................................................ 16
Open Motors ......................................................................................... 16
Greased Bearings on New Balance Q5800 Motors............................... 16
Foundation ............................................................................................ 17
Clearance ............................................................................................. 17
Isolators ................................................................................................ 22
INSTALLATION ............................................................................................. 22
Rigging Unit to Final Location ............................................................... 22
Locating and Installing Isolator Pads..................................................... 22
Checking the Isolation Pad Deflection................................................... 22
Leveling the Unit ................................................................................... 22
Installing Optional Spring Isolators........................................................ 22
Piping Connections ............................................................................... 22
Cooler and Condenser Water Piping..................................................... 22
Refrigerant Relief Piping ....................................................................... 24
Unit Piping ............................................................................................ 24
Control Wiring ....................................................................................... 25
Power Wiring ........................................................................................ 25
Insulation .............................................................................................. 26
Installation Check – Request for Start-up Service ............................... 26

4YORK INTERNATIONAL
FIG. 1 – MODELYK MILLENNIUM CHILLER
28815A
CONTROL
CENTER
COMPRESSOR
COOLER
CONDENSER
MOTOR
FRONT VIEW
OIL PUMP
CONTROL PANEL

YORK INTERNATIONAL 5
FORM 160.52-N1
NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For compact water boxes (shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 1/2" to nozzle length for flanges connections.
4. To determine overall height, add 7/8" for isolators.
5. Use of motors with motor hoods may increase overall unit dimensions.
H2 COMPRESSORS
COOLER – CONDENSER SHELL CODES
F–F F—G G–F G–G H–G
A7'–2" 7'–6" 7'–4-1/2" 7'–8-1/2" 8'–0"
B8'–6-3/4" 8'–10-1/4" 8'–6-3/4" 8'–10-1/4" 8'–10-1/4"
C2'–0" 2'–0" 2'–1-1/4" 2'–1-1/4" 2'–3"
D1'–7" 1'–9" 1'–7" 1'–9" 1'–9"
E0'–5-7/8" 0'–5-7/8" 0'–6-1/4" 0'–6-1/4" 0'–6-1/4"
H3 COMPRESSORS
COOLER – CONDENSER SHELL CODES
G–F G–G H–G
A7'–4-1/2" 7'–8-1/2" 8'–0"
B8'–6-3/4" 8'–10-1/4" 8'–10-1/4"
C2'–1-1/4" 2'–1-1/4" 2'–3"
D1'–7" 1'–9" 1'–9"
E0'–6-1/4" 0'–6-1/4" 0'–6-1/4"
H1 COMPRESSORS
COOLER – CONDENSER SHELL CODES
E–E E–F F–E F–F F–G G–F G–G
A6'–6" 6'–9" 6'–11" 7'–2" 7'–6" 7'–4-1/2" 7'–8-1/2"
B8'–1" 8'–3-1/2" 8'–1" 8'–3-1/2" 8'–7-1/2" 8'–3-1/2" 8'–7-1/2"
C1'–9-1/2" 1'–9-1/2" 2'–0" 2'–0" 2'–0" 2'–1-1/4" 2'–1-1/4"
D1'–5-1/2" 1'–7" 1'–5-1/2" 1'–7" 1'–9" 1'–7" 1'–9"
E0'–5-7/8" 0'–5-7/8" 0'–5-7/8" 0'–5-7/8" 0'–5-7/8" 0'–6-1/4" 0'–6-1/4"
H0 COMPRESSORS
COOLER – CONDENSER SHELL CODES
D–D D–E E–D E–E E–F F–E F–F
A6'–4" 6'–4" 6'–6" 6'–6" 6'–9" 6'–11" 7'–2"
B8'–0-1/2" 8'–1" 8'–0-1/2" 8'–1" 8'–3-1/2" 8'–1" 8'–3-1/2"
C1'–8-1/2" 1'–8-1/2" 1'–9-1/2" 1'–9-1/2" 1'–9-1/2" 2'–0" 2'–0"
D1'–5-1/2" 1'–5-1/2" 1'–5-1/2" 1'–5-1/2" 1'–7" 1'–5-1/2" 1'–7"
E0'–5-5/8" 0'–5-5/8" 0'–5-7/8" 0'–5-7/8" 0'–5-7/8" 0'–5-7/8" 0'–5-7/8"
G4 COMPRESSORS
COOLER – CONDENSER SHELL CODES
C–C C–D D–C D–D D–E
A6'–1" 6'–1" 6'–4" 6'–4" 6'–4"
B7'–10-1/2" 8'–0-1/2" 7'–10-1/2" 8'–0-1/2" 8'–1"
C1'–7" 1'–7" 1'–8-1/2" 1'–8-1/2" 1'–8-1/2"
D1'–5-1/2" 1'–5-1/2" 1'–5-1/2" 1'–5-1/2" 1'–5-1/2"
E0'–5-5/8" 0'–5-5/8" 0'–5-5/8" 0'–5-5/8" 0'–5-5/8"
FIG. 2 – DIMENSIONS – G & H COMPRESSOR UNITS (FT.–IN.)
LD01338
B4, 5

6YORK INTERNATIONAL
NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For compact water boxes (shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 13 mm to nozzle length for flanges connections.
4. To determine overall height, add 22 mm for isolators.
5. Use of motors with motor hoods may increase overall unit dimensions.
G4 COMPRESSORS
COOLER – CONDENSER SHELL CODES
C–C C–D D–C D–D D–E
A1854 1854 1930 1930 1930
B2400 2451 2400 2451 2464
C483 483 521 521 521
D445 445 445 445 445
E143 143 143 143 143
H0 COMPRESSORS
COOLER – CONDENSER SHELL CODES
D–D D–E E–D E–E E–F F–E F–F
A1930 1930 1981 1981 2057 2108 2184
B2451 2464 2451 2464 2527 2462 2527
C521 521 546 546 546 610 610
D445 445 445 445 483 445 483
E143 143 149 149 149 149 149
H1 COMPRESSORS
COOLER – CONDENSER SHELL CODES
E–E E–F F–E F–F F–G G–F G–G
A1981 2057 2108 2184 2286 2248 2350
B2464 2527 2462 2527 2324 2527 2324
C546 546 610 610 610 641 641
D445 483 445 483 533 483 533
E149 149 149 149 149 159 159
H2 COMPRESSORS
COOLER – CONDENSER SHELL CODES
F–F F–G G–F G–G H–G
A2184 2286 2248 2350 2438
B2527 2324 2527 2324 2691
C610 610 641 641 686
D483 533 483 533 533
E149 149 159 159 159
H3 COMPRESSORS
COOLER – CONDENSER SHELL CODES
G–F G–G H–G
A2248 2350 2438
B2527 2324 2691
C641 641 686
D483 533 533
E159 159 159
LD01339
362 mm
4268 mm
362 mm
B4, 5
FIG. 2A – DIMENSIONS – G & H COMPRESSOR UNITS (mm)

YORK INTERNATIONAL 7
FORM 160.52-N1
FIG. 3 – DIMENSIONS – J COMPRESSOR UNITS (FT.–IN.)
NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For compact water boxes (shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 1/2" to nozzle length for flanges connections.
4. To determine overall height, add 7/8" for isolators.
5. Use of motors with motor hoods may increase overall unit dimensions.
J1/J2 COMPRESSORS
COOLER – CONDENSER SHELL CODES
G-G G-H H-G H-H H-J J-H J-J T-T
A7'–6" 7'–10" 7'–10-1/2" 8'–2-1/2" 8'–6-1/2" 8'–11" 9'–1" 9'–1"
B9'–3-3/4" 9'–9-3/4" 9'–3-3/4" 9'–9-3/4" 9'–9-3/4" 9'–9-3/4" 9'–9-3/4" 9'–9-1/2"
C2'–0" 2'–0" 2'–2-1/4" 2'–2-1/4" 2'–2-1/4" 2'–5-1/2" 2'–5-1/2" 2'–5-1/2"
D1'–9" 1'–11" 1'–9" 1'–11" 2'–1" 1'–11" 2'–1" 2'–1"
E14'–0" 14'–0" 14'–0" 14'–0" 14'–0" 14'–0" 14'–0" 16'–0"
F1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4"
G1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4"
J3 COMPRESSORS
COOLER – CONDENSER SHELL CODES
H-H H-J J-H
A8'–2-1/2" 8'–6-1/2" 8'–9"
B9'–8-3/4" 10'–0-3/4" 9'–8-3/4"
C2'–2-1/4" 2'–2-1/4" 2'–5-1/2"
D1'–11" 2'–1" 1'–11"
E14'–0" 14'–0" 14'–0"
F1'–11-3/4" 1'–11-3/4" 1'–11-3/4"
G1'–2-3/4" 1'–2-3/4" 1'–2-3/4"
J3/J4 COMPRESSORS
COOLER – CONDENSER SHELL CODES
J-J T-T T-V V-T V-V W-V
A9'–1" 9'–1" 9'–6" 9'–1" 9'–6" 9'–11"
B10'–0-3/4" 10'–0-3/4" 10'–5-3/4" 10'–0-3/4" 10'–5-3/4" 10'–5-3/4"
C2'–5-1/2" 2'–5-1/2" 2'–5-1/2" 2'–5-1/2" 2'–5-1/2" 2'–8"
D2'–1" 2'–1" 2'–3-1/2" 2'–1" 2'–3-1/2" 2'–3-1/2"
E14'–0" 16'–0" 16'–0" 16'–0" 16'–0" 16'–0"
F1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 1'–11-3/4" 2'–0-3/4"
G1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–2-3/4" 1'–4-1/2"
COND. 1 PASS 2 PASS 3 PASS
CODE HJKJKJ K
G5-7/8" 1'–1-3/4" 1'–1-3/4" 1'–1-3/4" 1'–1-3/4" 1'–1-3/4" 1'–1-3/4"
H11-5/8" 1'–8-7/8" 1'–8-7/8" 1'–6-1/8" 1'–6-1/8" 1'–4-5/8" 1'–8"
J1'–0-1/2" 1'–9-5/8" 1'–9-5/8" 1'–7-1/2" 1'–7-1/2" 1'–6-3/4" 1'–10"
T1'–0-1/2" 1'–9-5/8" 1'–9-5/8" 1'–7-1/2" 1'–7-1/2" 1'–6-3/4" 1'–10"
V1'–1-5/8" 1'–11" 1'–11" 1'–10" 1'–10" 1'–7-1/2" 1'–11-1/4"
J COMPRESSOR UNITS

8YORK INTERNATIONAL
FIG. 3A – DIMENSIONS – J COMPRESSOR UNITS (mm)
NOTES:
1. All dimensions are approximate. Certified dimensions are available on request.
2. For compact water boxes (shown above), determine overall unit length by adding water box depth to tube sheet length.
3. Water nozzles can be located on either end of unit. Add 1/2" to nozzle length for flanges connections.
4. To determine overall height, add 22 mm for isolators.
5. Use of motors with motor hoods may increase overall unit dimensions.
J1/J2 COMPRESSORS
COOLER – CONDENSER SHELL CODES
G-G G-H H-G H-H H-J J-H J-J T-T
A2286 2388 2400 2502 2604 2718 2769 2769
B2838 2991 2838 2991 2991 2991 2991 2985
C610 610 667 667 667 749 749 749
D533 584 533 584 635 584 635 635
E4267 4267 4267 4267 4267 4267 4267 4877
F603 603 603 603 603 603 603 603
G375 375 375 375 375 375 375 375
J3 COMPRESSORS
COOLER – CONDENSER SHELL CODES
H-H H-J J-H
A2502 2604 2667
B2965 3067 2965
C667 667 749
D584 635 584
E4267 4267 4267
F603 603 603
G375 375 375
J3/J4 COMPRESSORS
COOLER – CONDENSER SHELL CODES
J-J T-T T-V V-T V-V W-V
A2769 2769 2896 2769 2896 3023
B3067 3067 3194 3067 3194 3194
C749 749 749 749 749 813
D635 635 699 635 699 699
E4267 4877 4877 4877 4877 4877
F603 603 603 603 603 629
G375 375 375 375 375 419
COND. 1 PASS 2 PASS 3 PASS
CODE HJKJKJ K
G149 349 349 349 349 349 349
H295 530 530 460 460 422 508
J318 549 549 495 495 476 559
T318 549 549 495 495 476 559
V346 584 584 559 559 495 591
J COMPRESSOR UNITS

YORK INTERNATIONAL 9
FORM 160.52-N1
SHIPPING OPERATING REFRIGERANT LOADING PER
SHELLS WEIGHT WEIGHT CHARGE ISOLATOR
(LBS) (KG) (LBS) (KG) (LBS) (KG) (LBS) (KG)
CBCB 16670 7580 20000 9090 1025 470 5000 2273
CBCC 16730 7600 20100 9140 1025 470 5025 2285
CBCD 16870 7670 20200 9180 1025 470 5050 2295
CCCB 16900 7680 20300 9230 1025 470 5075 2308
CCCC 16960 7710 20300 9230 1025 470 5075 2308
C-C CCCD 17100 7770 20500 9320 1025 470 5125 2330
CDCB 17170 7800 20500 9320 1025 470 5125 2330
CDCC 17230 7830 20600 9360 1025 470 5150 2340
CDCD 17370 7900 20700 9410 1025 470 5175 2353
CECB 17430 7920 20800 9450 1025 470 5200 2363
CECC 17490 7950 20900 9500 1025 470 5225 2375
CECD 17630 8010 21000 9550 1025 470 5250 2388
CBDB 17060 7750 20400 9270 1025 470 5100 2318
CBDC 17070 7760 20400 9270 1025 470 5100 2318
CBDD 17360 7890 20700 9410 1025 470 5175 2353
CCDB 17300 7860 20700 9410 1025 470 5175 2353
CCDC 17310 7870 20700 9410 1025 470 5175 2353
C-D CCDD 17590 8000 21000 9550 1025 470 5250 2388
CDDB 17570 7990 20900 9500 1025 470 5225 2375
CDDC 17580 7990 21000 9550 1025 470 5250 2388
CDDD 17860 8120 21200 9640 1025 470 5300 2410
CEDB 17820 8100 21200 9640 1025 470 5300 2410
CEDC 17830 8100 21200 9640 1025 470 5300 2410
CEDD 18120 8240 21500 9770 1025 470 5375 2443
DDCB 17600 8000 21000 9550 1025 470 5250 2388
DDCC 17660 8030 21000 9550 1025 470 5250 2388
D-C DDCD 17800 8090 21200 9640 1025 470 5300 2410
DECB 17750 8070 21100 9590 1025 470 5275 2398
DECC 17820 8100 21200 9640 1025 470 5300 2410
DECD 17960 8160 21300 9680 1025 470 5325 2420
DBDB 17420 7920 20800 9450 1150 520 5200 2363
DBDC 17430 7920 20800 9450 1150 520 5200 2363
DBDD 17710 8050 21100 9590 1150 520 5275 2398
DCDB 17660 8030 21000 9550 1150 520 5250 2388
DCDC 17670 8030 21000 9550 1150 520 5250 2388
D-D DCDD 17960 8160 21300 9680 1150 520 5325 2420
DDDB 17990 8180 21400 9730 1150 520 5350 2433
DDDC 18000 8180 21400 9730 1150 520 5350 2433
DDDD 18290 8310 21700 9860 1150 520 5425 2465
DEDB 18150 8250 21500 9770 1150 520 5375 2443
DEDC 18160 8250 21500 9770 1150 520 5375 2443
DEDD 18450 8390 21800 9910 1150 520 5450 2478
DBEB 18680 8490 22400 10180 1150 520 5600 2545
DBEC 18890 8590 22700 10320 1150 520 5675 2580
DBED 19000 8640 22800 10360 1150 520 5700 2590
DCEB 18920 8600 22700 10320 1150 520 5675 2580
DCEC 19130 8700 22900 10410 1150 520 5725 2603
D-E DCED 19240 8750 23000 10450 1150 520 5750 2613
DDEB 19250 8750 23000 10450 1150 520 5750 2613
DDEC 19470 8850 23200 10550 1150 520 5800 2638
DDED 19570 8900 23300 10590 1150 520 5825 2648
DEEB 19410 8820 23200 10550 1150 520 5800 2638
DEEC 19620 8920 23400 10640 1150 520 5850 2660
DEED 19730 8970 23500 10680 1150 520 5875 2670
TABLE 1 – SHELL COMPRESSOR WEIGHT LESS MOTOR (G & H COMPRESSORS)

10 YORK INTERNATIONAL
SHIPPING OPERATING REFRIGERANT LOADING PER
SHELLS WEIGHT WEIGHT CHARGE ISOLATOR
(LBS) (KG) (LBS) (KG) (LBS) (KG) (LBS) (KG)
ECDB 18800 8550 22600 10270 1400 640 5650 2568
ECDC 18810 8550 22700 10320 1400 640 5675 2580
E-D ECDD 19100 8680 22900 10410 1400 640 5725 2603
EDDB 19050 8660 22900 10410 1400 640 5725 2603
EDDC 19060 8660 22900 10410 1400 640 5725 2603
EDDD 19350 8800 23200 10550 1400 640 5800 2638
EBEB 19810 9000 24000 10910 1400 640 6000 2728
EBEC 20020 9100 24300 11050 1400 640 6075 2763
EBED 20130 9150 24400 11090 1400 640 6100 2773
ECEB 20050 9110 24300 11050 1400 640 6075 2763
E-E ECEC 20260 9210 24500 11140 1400 640 6125 2785
ECED 20370 9260 24600 11180 1400 640 6150 2795
EDEB 20300 9230 24500 11140 1400 640 6125 2785
EDEC 20510 9320 24700 11230 1400 640 6175 2808
EDED 20620 9370 24900 11320 1400 640 6225 2830
EBFB 21140 9610 25800 11730 1585 720 6450 2933
EBFC 21260 9660 25900 11770 1585 720 6475 2943
EBFD 21440 9750 26100 11860 1585 720 6525 2965
ECFB 21380 9720 26000 11820 1585 720 6500 2955
E-F ECFC 21500 9770 26100 11860 1585 720 6525 2965
ECFD 21680 9850 26300 11950 1585 720 6575 2988
EDFB 21630 9830 26300 11950 1585 720 6575 2988
EDFC 21750 9890 26400 12000 1585 720 6600 3000
EDFD 21930 9970 26600 12090 1585 720 6650 3023
FCEB 21220 9650 25900 11770 1650 750 6475 2943
FCEC 21430 9740 26200 11910 1650 750 6550 2978
F-E FCED 21530 9790 26300 11950 1650 750 6575 2988
FDEB 21470 9760 26200 11910 1650 750 6550 2978
FDEC 21680 9850 26400 12000 1650 750 6600 3000
FDED 21790 9900 26500 12050 1650 750 6625 3013
FBFA 21550 9800 26900 12230 1805 820 6725 3058
FBFB 21960 9980 27300 12410 1805 820 6825 3103
FBFC 22080 10040 27400 12450 1805 820 6850 3113
FBFD 22260 10120 27600 12550 1805 820 6900 3138
FCFA 21860 9940 27200 12360 1805 820 6800 3090
F-F FCFB 22270 10120 27600 12550 1805 820 6900 3138
FCFC 22400 10180 27800 12640 1805 820 6950 3160
FCFD 22580 10260 27900 12680 1805 820 6975 3170
FDFB 22530 10240 27900 12680 1805 820 6975 3170
FDFC 22650 10300 28000 12730 1805 820 7000 3183
FDFD 22830 10380 28200 12820 1805 820 7050 3205
FBGB 24140 10970 29900 13590 1805 820 7475 3398
FBGC 24550 11160 30300 13770 1805 820 7575 3443
FBGD 24820 11280 30500 13860 1805 820 7625 3465
FCGB 24460 11120 30200 13730 1805 820 7550 3433
F-G FCGC 24870 11300 30600 13910 1805 820 7650 3478
FCGD 25140 11430 30900 14050 1805 820 7725 3513
FDGB 24720 11240 30400 13820 1805 820 7600 3455
FDGC 25130 11420 30800 14000 1805 820 7700 3500
FDGD 25400 11550 31100 14140 1805 820 7775 3535
TABLE 1 – SHELL COMPRESSOR WEIGHT LESS MOTOR (G & H COMPRESSORS) (Cont’d)