Ytc YT-1200L User manual

Pneumatic Positioner
YT-1200 Series
USER'S MANUAL
YTC Ver 1.01

Introduction
Thank you for choosing YTC product. Each product is fully inspected after the production to
offer you the highest quality. In order to fully utilize the product, we strongly recommend users
to read this manual carefully and understood.
The manual should be given to the end-user.
The manual can be changed or revised without any prior notice. Any changes in
product’s specification, structure, and/or any components may not result immediate
revised version of the manual.
The manual should not be duplicated or reproduced for any purpose without any
approvals from Young Tech Co., Ltd, South Korea / YTC.
Manufacturer Warranty
For the safety, it is imperative to follow instructions in the manual. It is not manufacturer's
liability for any damages which caused by users' negligence.
It is not manufacturer's liability for any damages or accidents which resulted by any alteration
or modification of the product and parts. If alteration or modification is necessary, please
contact the manufacturer directly.
Manufacturer warrants the product from the date of original retail purchase of the product for
one (1) year, except as otherwise stated.
Manufacturer warranty will not cover the products that the product have been subjected to
abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the
documentation for the product, or if the model or serial number has been altered, tampered
with, defaced or removed; damages that occurs in shipment, due to act of God, failure due to
power surge, and cosmetic damage. Improper or incorrectly performed maintenance or
report voids this Limited Warranty.
For detailed warranty information, please contact the corresponding local Young Tech Co.,
Ltd office or main office in South Korea.

Product Description
Main Features and Functions
The product can operate normally in very extreme environment, such as vibration and
temperature.
The durability has been proven after testing 2 million cycles at the minimum.
Response time is very short and accurate.
Simple part change can set 1/2 Split Range.
It is economical due to less air-consumption.
Direct / Reverse action can be set easily.
Zero & Span adjustment processes are simple.
Feedback connection is easy.
Operation Logic
Bellows(①) push flapper(②) if input pressure increases. Then the gap between nozzle(③) and
flapper(②) increases, which results pressure in upper spool(⑤) exhaustion. This would cause
spool(⑤) to rise upward. As the spool(⑤) rises, it pushes format(⑧), and the air pressure will be
supplied to the actuator(⑩). As the actuator's inner pressure increases, the actuator stem(⑫) will
move. For graphical diagram, please refer to <Figure 1>.

Label Description
Model: Indicates model name and any options (if any)
Input Signal: Indicates current input signal range.
Supply Pressure: Indicates the range of supply pressure.
Serial Number: Indicates unique serial number.
Suffix Symbol
YT-1200 series follows suffix symbols as below.

Specification

Parts and Assembly

Dimensions

Installation
Safety Warning
When installing a positioned, please ensure to read and follow safety instruction.
All input and supply pressure to valve, actuator, and other related devices must be turned
off.
Use bypass valve or other equipment to avoid entire system “shut down.”
Make sure there is no remaining pressure in the actuator.
Tools for Installation
① Hexagonal wrench
② Screw Drivers (+) and (-)
③ Spanners for hexagonal-head bolts
YT-1200 Installation
YT-1200L should be installed on linear motion valve such as globe valve or gate valve using
spring return type diaphragm or piston actuator. Before installation, be sure to check for
following installation components.
① YT-1200L main body
② Feedback lever and lever spring
③ Flange nut (bottom side of YT-1200L)
④ 4 pcs of hexagon head bolts (M8 x 1.25P)
⑤ 4 pcs of M8 plate washer
Installation Steps
1. Proper bracket must be made in order to attach positioned on the actuator yoke. Please
consider following when making a bracket.
A. Feedback lever should be leveled at 50% of the valve stroke. (refer to step G)
B. Feedback lever connection bar of the actuator damp should be installed at the
positioned that the valve stroke and numbers which indicated on the feedback lever
must be fitted. (refer to step H)
2. Attached YT-1200L to the bracket, which was produced in
previous step, by using bolts. <Fig 1> Please refer to
backside of the unit for size of the bolts. The standard
size of bolt is M8 x 1.25P and other bolts sizes are
available. Please contact YTC sales department.
3. Attach YT-1200L (with bracket) to the actuator yoke – DO

NOT TIGHTEN COMPLETELY.
4. Connect YT-1200L feedback lever to the actuator clamp. The gap on the YT-1200L
feedback lever is 65mm. The connection bar thickness should be less than 6.3mm.
<Fig 2>
5. Connect air filter regulator to the actuator temporarily. Set supply pressure of the
regulator in order to position the actuator damp at 50% of valve stroke. <Fig 3>
6. Insert connection bar into the YT-1200L feedback lever. The connection bar should be
inserted at the 50% point on the feedback lever, which would help to reduce hysteresis.
<fig 4>

7. If connection bar does not point at 50% point, then adjust bracket or feedback link bar
position. Failure to position at 50% would lower the linearity of the positioner. <fig 5>
8. Check valve stroke. The stroke numbers are indicated on the feedback lever. Position
connection bar at the number on the feedback lever according to the valve stroke. <fig
6> To adjust, move the bracket or the connection bar.
NOTE
After installing YT-1200L, operate the valve from
0% to 100% stroke by using air filter regulator.
Both of 0% and 100%, the feedback lever
should not touch the lever stopper, which is
located on the backside of YT-1200L. <fig 7>
If the feedback lever touches the stopper, YT-
1200L should be installed further away from the
center of the yoke.
9. After the proper installation, tighten all of the
bolts on the bracket, the feedback lever, and the connection bar.

YT-1200R Installation
YT-1200R should be used for rotary motion valve, that is ball valve, butterfly valve using rack
and pinion, scotch yoke or complex type actuator, which its stem rotates 90 degrees. Before
installation, be sure to check for following installation components.
① YT-1200R main body
② Fork lever and lever spring
③ 1 set of bracket (3 pcs)
④ 4 pcs of hexagon head bolt M8 x 1.25P
⑤ 4 pcs of M8 plate washer
YT-1200R Install Example

Bracket Information
YT-1200R is supplied with standard bracket. The bracket can be used for fork lever and
NAMUR bracket. Please see <fig 8> for more detailed information.
1. Standard actuator stem height (H) is 20, 30, or 50 mm. After check “H”, assemble with
the bracket as shown in <fig 8 & 9>
2. Attached bracketed YT-1200R to the actuator
by using hexagonal-headed and wrench bolts.
Size of the bracket hole is 6mm. When
tightening bolts, use spring washer or similar
for complete attachment to the actuator, so
YT-1200R will not be shaken by vibration or
any other impact. The direction of bracket is
different by the operating condition, but in
general, the positioned is installed as shown.
<fig 10>

3. Set rotation position of the actuator stem at zero point, “0%”. For a single type of
actuator, it is easy to check zero point, because the actuator stem is positioned at zero
point when there is no supply pressure. If double acting actuator is used, check actuator
stem’s rotation direction (clockwise or counter-clockwise) by supplying pressure.
4. Install the fork lever as shown in <fig11> after setting actuator stem at zero point.
Check the direction of the actuator stem – clockwise or counter-clockwise. Installation
angle of the fork lever should be 45 degrees based on the linear shaft. For NAMUR
shaft, the angle does not matter.
5. After setting fork lever position, lock nuts which are assembled on bottom of the fork
lever.
6. Attach YT-1200R to the bracket. Fix the damping pin on the main shaft of YT-1200R and
insert connection bar into the fork lever slot, so it can be locked to the fork lever spring.
This sets the alignment of the main shaft of YT-1200R and center of the actuator stem.
Bad alignment of the main shaft and the actuator stem lowers YT-1200R’s durability,
because too much force will be on the main shaft of YT-1200R. <fig 12>

7. Tighten YT-1200R base and the bracket with hexagon-headed bolts and plate washer. It
is recommended to tighten four bolts after checking YT-1200R’s position. <fig 13>

Piping Connection
Note
To avoid entering moisture, oil, or dust into the product, please carefully make
selection of supply pressure compressor.
It is recommended to attach air filter regulator <YT-200> before supply port of YT-
1200.
Supply Pressure Condition
① Dry air with at least 10℃ lower than ambient temperature.
② Avoid from dusty air. Filter can only sort 5 micron or larger.
③ Avoid any oil.
④ Comply with ANSI/ ISA-573 1975(R1981) and ISA S73-1975(R1981).
⑤ Not to be used beyond the range of 1.4 – 7 kgf/cm2 (140 – 700 kPA).
⑥ Set air filter regulator’s supplied pressure 10% higher than actuator’s spring range
pressure.
Pipe Condition
① Make sure inside of pipeline is emptied.
② Do not use pipeline that has been squeezed or has hole.
③ To maintain flow rate, use the pipeline that has more than 6mm inner diameter.
(10mm outer diameter)
④ Do not use extremely long pipeline system. It may affect flow rate due to the
friction inside of the pipeline.
Piping connection with actuator
-Single Acting Actuator
YT-1200 series single acting type is set to use OUT1 port. OUT1 port should be
connected with supply pressure port from actuator when using single acting type of
spring return actuator. <fig 14 & 15>

-Double Acting Actuator
For YT-1200 series double acting type, when inputting current signal, supply pressure
is our from OUT1 port. Please refer to <fig 16 & 17>
Adjustment
Adjustment – Cam
①Direction of actuator's stem rotation must be checked when supply signal is supplied.
When actuator's stem rotates clockwise, the face of cam must be shown "DA." On the
other hand, when the stem rotates counter-clockwise, adjust cam so "RA" shows on the
face of cam.
② Check whether actuator's angle is at the initial point.
③ After checking the initial point, release the hexagonal flange nut and adjust the position
of the bearing so it is at 0 point. <Figure 18>
④ When produced, the cam is set as RA.

Adjustment – Zero Point
①Set supply signal at 3 psi and rotate adjuster clockwise or counter-clockwise to adjust
actuator's rotation angle. <Figure 19>
② When adjusting zero for single actuator, rotation angle is equal to positioner's pressure
gauge.
Adjustment – Span
①After setting zero, rotate Span screw so supply signal reaches at the span point on
the indicator.
② Changing span point affects zero point setting. So zero setting must be set again.
After setting zero point, confirm the span point. This step must be repeated until
both points are properly set.
③ If 1/2 split range is used, YT-1200L can be used after span and zero point are set.
For YT-1200R with 1/2 split range, the span spring must be changed.
④ After setting is completed, tighten Lock Screw. <Figure 20>

Adjustment – A / M Switch <Auto / Manual>
1. A / M switch adjusts the valve operation to
automatic or manual.
2. YT-1200 series is set as “A” / Automatic as default.
If user wants to set as “M” / Manual, the setting can
be adjusted by turning the switch counter-clockwise.
<fig 21>
3. If the setting is at “M”, the air pressure will be
supplied to the actuator directly. Always set the
setting back to “A” after any change.
4. If OUT2 in single acting actuator or double acting
actuator is used, A / M switch will not operate.
Adjustment – Seat Adjuster
① Seat adjuster is set according to the customer’s request before the positioned is
delivered. Please do not adjust the seat adjuster.
② Seat adjuster is used for double acting actuator. Please do not touch the seat
adjuster, because it can affect the positioner’s performance.

Troubleshooting
Positioner does not respond to the input signal.
①Check supply pressure level. The level must be at least 1.4 kgf/cm2
②Check if input signal is properly supplied to the positioned. The signal should be 3-
15 psi.
③Check if the positioner’s nozzle has been blocked. Also, check if the pressure is
supplied to the positioned and the pressure is being exhausted through the nozzle.
If the nozzle has been blocked by any substances, please send the unit to YTC for
repair.
④Check if feedback lever has been installed properly.
The pressure of OUT1 reaches exhausting pressure level and does not come back
down.
①Check A / M switch. If the switch has been damaged, replace the switch or pilot
relay valve.
②Check for a gap or damages between the nozzle and the flapper. If damaged,
please send the unit to YTC for repair.
The pressure is exhausted only by A / M switch.
①Check if the positioner’s nozzle has been blocked. Also, check if the pressure is
supplied to the posiioner and the pressure is being exhausted trough the nozzle. If
the nozzle has been blocked by any substances, please send the unit to YTC for
repair.
Hunting occurs.
①Check if safety spring has been displaced. <Next to pilot relay valve>
②Check if the size of actuator is too small. If so, insert an orifice in order to reduce
the pressure flow rate.
③Check if there is any friction between the valve and the actuator. If so, increase
actuator’s size or reduce the friction level.
Actuator only operates by on / off.
①Check pipe connection
②Check cam direction
Linearity is too low.
①Check if the feedback lever is properly installed. Especially check if the feedback
lever is parallel to the around at 50% point.
②Check if zero and span has been properly adjusted, that is not too low or not too