ZALMAN CNPS7000B-AlCu User manual

* Applies to all versions of CNPS7000B LED.
* Please read before installation.
http://www.zalman.co.kr http://www.zalmanusa.com
CNPS7000B
Intel Pentium 4
Socket 478 CPU
Socket 775 CPU (ZM-CS1 separate
purchase necessary)
AMD Duron/Athlon/Athlon XP/Sempron
Socket 462 CPU
AMD Sempron/AMD64 (Athlon 64/Opteron)
Socket 754/939/940 CPU
User
’’
s Manual
(English version)
User
’’
s Manual

1) Does not generate noise or vibration in Silent Mode.
2) Pure copper and/or pure aluminum base materials ensure excellent heat dissipation.
3) Intel Pentium (Socket 78), AMD Duron / Athlon / Athlon XP / Sempron (Socket 62), and Sempron /
AMD6 (Socket 75 /939/9 0) compatible design for broad compatibility. (To use this product on
socket 775, ZM-CS1 must be purchased separately.)
) 92mm fan inside the FHS maximizes airflow and makes installation easier.
5) The high intensity blue LEDs on CNPS7000B LED coolers stay bright even in Silent Mode.
6) Adjustable fan speed controller (FAM MATE 2) enables control of noise and fan performance.
2) Fan
- Bearing Type : 2-Ball
- Rotation Speed : 1,350 ~ 1,800rpm 10 % (Silent Mode)
1,800 ~ 2,600rpm 10 % (Low-noise Mode)
- Noise Level : 18 ~ 21dB 10% (Silent Mode) - measured at 1m distance from noise source
21 ~ 27.5dB 10% (Low-noise Mode) - measured at 1m distance from noise source
3) FAN MATE 2
- Output Voltage : 5V ~ 11V 2 %
- Allowable Power : 6W or lower
Note 1)
The maximum weight for a cooler is specified as 50g for Intel Socket 78/775 and AMD Socket 75 /939/9 0
and 300g for AMD Socket 62. Special care should be taken when moving a computer equipped with a
cooler which exceeds the relevant weight limit. Zalman is not responsible for any damage that occurs when
moving a computer.
1) Flower Heats nk (FHS)
CNPS7000B-AlCu CNPS7000B-Cu
Model
Spec.
Weight (g)
T.R.
(°C/W )
Silent Mode
Normal Mode
438(1)
0.29
0.22
109 (L) X 109 (W) X 62 (H)
3,154
755(1)
0.27
0.20
Dimensions (mm)
Dissipation Area ( ㎠ )
※
The specifications of any product may change without prior notice to improve performance.
1
1. Features
. Exploded View
2. Specifications
Fan
Clip
Fan Support
Fan Fixing Screw
Bolt
Fan Support Fixing Screw
FHS

※
The specifications of any product may change without prior notice to improve performance.
2
󳣍Korean Patent Application No. 00-5 635
󳣍Korean Design Applications Nos. 02-17 70, 02-25208, 02-25209 etc.
󳣍Patent Applications pending in over 20 nations around the world, including USA, EU, and Japan
4. Patents
1) Common Components
❶ FHS Assembly (CNPS7000B-AlCu/Cu)
❷ Four ( ) Bolts (for installing the FHS)
❸ Thermal Grease
❹ Fan Speed Controller (FAN MATE 2)
❺ Double - sided Tape (for installing FAN MATE 2)
❻ Cable for FAN MATE 2
❼ User’s Manual (in English and Korean)
❶
❽
❾
❿
󱆎󱆏
❷
❹
❸
❺
❼
❻
5. Components
2) Components for Intel Pentium (Socket 78)
❽ Two (2) Clip Supports For Socket 78
3)
Components for AMD Duron / Athlon / Athlon XP /
Sempron (Socket 62)
❾ One (1) A-Type (blue) Clip Support for Socket 62
❿ One (1) B-Type (white) Clip Support for Socket 62
󱆌 Four ( ) Bolts (for fastening the Clip Supports)
󱆍 One (1) set of Washers
) Components for AMD Sempron / AMD6 (Socket 75 /939/9 0)
󱆎 Two (2) Nipples
󱆏 One (1) Backplate for AMD6
󱆐 Small washers (from component 󱆍 )
󱆌
Precautions
1) If excessive force is exerted on the fan, it may malfunction and result in damage to the product and/or the computer.
2) Do not put your finger in the fan while it is running.
3) Keep the product away from children.
) Check the components list and condition of the product before installing. If there is any problem, contact the shop
where you purchased it and get a replacement or refund.
5) The exposed core of a Socket 62 CPU can be cracked if proper care is not taken. Read the “Installation” section
thoroughly before installing.
NOTICE) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not
limited to, improper use, problems with electrical power, accident, neglect, alteration, repair,
improper installation, or improper testing.
󱆍󱆐

※
The specifications of any product may change without prior notice to improve performance.
1) Intel Pent um 4 - Socket 478/775
All CPUs conforming to Socket 78 & all CPUs conforming to Socket 775 up to model 5 0
Notes)
3. GHz Northwood, Prescott- 78 of 2.8A/E GHz or higher, and Prescott-775 of up to model 5 0 generate
exorbitant amount of heat (8 W ~ 103W). Refer to the table below and adjust the fan speed so that the
CPU-Case temperature (T
C ) is lower than the maximum CPU-Case temperature (T C_MAX ).
※ Hardware monitoring programs report CPU-Die
temperature (T
D ) as the CPU temperature.
CPU-Die temperature (T
D ) is measured about
~ 10℃higher than CPU-Case temperature (T
C )
depending on the motherboard and/or BIOS.
Refer to the Zalman website for more information.
※ To use this product on Socket 775, ZM-CS1 (clip support for Socket 775) must be purchased separately.
6. Compatible CPUs
Cautions )
①For Socket 78, as shown in Figure 2, a motherboard that is not compliant with the“10.2mm Motherboard
component height restriction”standard, introduced by Intel, may create interference between
components and the clip. Please do not install the CNPS7000B if this interference is observed.
②No motherboard components with a height greater than 39mm, as well as the PSU, disk drives, VGA card,
and RAM should be present within a 55 mm radius from the center of the CPU.
③For more information, please visit the Zalman website and click on“Compatibility between CNPS7000(A/B)
and Socket 78 Pentium Motherboards” link.
2) AMD Duron / Athlon / Athlon XP / Sempron - Socket 462
All CPUs conforming to Socket 62 platform
Cautions )
①This product requires “Heatsink Attach Holes”around the
CPU socket as shown on the right.
②No motherboard components with a height greater than 39mm, as well
as the PSU, disk drives, VGA card, and RAM should be present within a
55 mm radius from the center of the CPU.
③
This product cannot be installed if any motherboard component (usually
capacitor) taller than 15mm is located under the clip.
④For more information, please visit the Zalman website
and refer to
“CNPS7000A/B Compatible Socket 62 Motherboards List”
link.
T C
T D
IHS
CPU Die T
D > T C
10.2mm Motherboard component height restriction
F gure 1
Compat ble
F gure 2
Not Compat ble
4mm
Clip
Motherboard
Component
Clip
Motherboard Component
②
①
③
Northwood
3.4
68 69.1
2.8A/E, 3.0E 3.2E, 3.4E 520, 530, 540
Prescott - 478 Prescott - 775
CPU
T C_MAX
73.2 67.7
℃℃℃℃

※
The specifications of any product may change without prior notice to improve performance.
4
3) AMD Sempron / AMD64 - Socket 754/939/940
All CPUs conforming to Socket 75 /939/9 0 platform
Cautions )
①No motherboard components with a height greater than 39mm, as
well as the PSU, disk drives, VGA card, and RAM should be present
within a 55mm radius from the center of the CPU.
②For more information, please visit the Zalman website and refer to
“CNPS7000(A/B) Compatible Socket 75 /939/9 0 Motherboards
List”
link.
1) Apply Thermal Grease
Clean off particles and residue then spread a thin layer of
thermal grease on the CPU.
2) Install Cl p Supports for Socket 478
Install the clip supports for socket 78 on both sides of
the retention guide as shown in the diagram.
3) Insert Bolts
Insert the two bolts into the inner holes of the clip.
4) Place FHS
Set the FHS at the center of the CPU. Screw the bolts in
slightly, then tighten each bolt a few turns at a time while
alternating between the two until the clip supports are
completely pressed against the clip.
7. Installation (Intel Pentium 4 - 478)
5) Connect Power (How to use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
FHS
Clip Support for
Socket 78
Bolt
Inner Hole
Clip
Retention Guide
Clip Support for Socket 78
󳦈
󳦇
󳦊
CPU (IHS)
Thermal Grease
①

※
The specifications of any product may change without prior notice to improve performance.
5
1) Install Cl p Supports for Socket 462
Install the clip supports for socket 62 on the motherboard. Make sure to place A-type (blue : nstalled
near the lever) and B-type (wh te) supports at the appropr ate locat on.
The installation should be done in the order of : bolts > small washers > motherboard > small washers >
clip supports (see below).
2) Apply Thermal Grease
Clean off particles and residue then spread a thin layer
of thermal grease on the CPU core (only on the chip's
surface that makes contact with the FHS base).
8. Installation (AMD Duron / Athlon / Athlon XP / Sempron - 462)
5) Connect Power (How to use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
3) Insert Bolts
Insert the two bolts into the inner holes of the clip.
4) Place FHS
Set the FHS at the center of the CPU. Screw the
bolts in slightly, then tighten each bolt a few turns at a time
while alternating between the two until the clip supports
are completely pressed against the clip.
FHS
Clip Support for
Socket 62
Bolt
Inner Hole
Clip
CPU
Thermal Grease
Clip Support B for Socket 62 (White)
Lever
Small Washer
Motherboard
Small Washer
Bolt
Clip Support B for Socket 62 (White)
Clip Support A for
Socket 62 (Blue)

※
The specifications of any product may change without prior notice to improve performance.
6
1) Fasten N pples
Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the
Backplate for AMD6 is firmly attached to the motherboard on the opposite side of the CPU.
* A Retention Guide is not necessary for installing CNPS7000B on Socket 75 /939/9 0.
3) Insert Bolts
Insert the two bolts into the outer holes of the clip.
4) Place FHS
Set the FHS at the center of the CPU. Screw the
bolts in slightly, then tighten each bolt a few turns at a
time while alternating between the two until the nipples
are completely pressed against the clip.
9. Installation (AMD Sempron / AMD64 - 754/9 9/940)
5) Connect Power (How to use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
2) Apply Thermal Grease
Clean off particles and residue then spread a thin layer of
thermal grease on the CPU.
FHS
Nipple
Bolt
Outer Hole
Clip
CPU (Lid)
Thermal Grease
Backplate for AMD6
Nipple
Motherboard
Small Washer

※
The specifications of any product may change without prior notice to improve performance.
7
1) Installing FAN MATE 2 on the Inside of the System 2) Installing FAN MATE 2 on the Outside of the System
※FAN MATE 2 Installation and Usage
11. Thermal Resistance (℃/W) & Noise (dB) Curve
Connect the appropriate 3-pin connector on the
cable to the motherboard fan header and the
CNPS7000B’s fan connector.
Pull the 6-pin connector out of the system through
the back and connect it to FAN MATE 2, which
should be installed on the case using the included
double-sided tape.
◆ When the speed control knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Silent Mode.
Turned fully clockwise, it operates in Normal Mode. You can select the desired fan speed by turning the knob.
Note) FAN MATE 2 has been specifically designed for the fan of this product. Zalman Tech Co., Ltd. is not
responsible for any damage to systems or CPUs caused by using it with other types of fans.
10. Notes on Usage
1) Check ng CPU Compat b l ty
Please refer to “Compatible CPUs” on page 3 to confirm that your CPU is compatible before using the CPU cooler.
2) Caut ons Dur ng Boot ng
When booting the computer, it may automatically power down after an alarm sound by a system
monitoring program to indicate that the CPU fan is rotating slowly. If this happens, turn the speed
control knob fully clockwise to increase the fan speed. Then set ‘CPU Fan Detected’ to ‘Disabled’ in the
BIOS settings, or set the slowest rotational speed of the CPU fan in the system monitoring program to
less than or equal to 1,300rpm.
Note) Some motherboards do not boot if the rotational speed of the CPU fan is below a certain
rpm. If the BIOS settings are updated, Silent Mode can be used. For more information on
updating your BIOS, please refer to your motherboard manufacturer's website. Disabling
CPU fan speed detection in BIOS settings does not affect computer performance.
3) Overclock ng
The fan should be set to Normal Mode if Overclocking.
(Zalman Tech Co., Ltd. is not responsible for any damage resulting from CPU Overclocking.)
Fan Connector
(CNPS7000B)
Motherboard
Double-sided Tape
FAN MATE 2
6-Pin Connector

※
The specifications of any product may change without prior notice to improve performance.
When building a noiseless computer, use Zalman’s Noiseless Power Supply, Fanless Northbridge Cooler,
Heatpipe HDD Cooler, Noiseless Case Fan, Heatpipe VGA Cooler, and Fan Controller for stable performance
and maintain a noiseless environment.
8
12. Zalman Noise Prevention System
Noiseless Power Supply Fanless Northbridge Cooler Heatpipe HDD Cooler
Noiseless Case Fan Heatpipe VGA Cooler Fan Controller
The TNN 500AF is the world's first absolutely no seless, ant -dust computer case for high-end systems that
has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High
Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN
Tech Co., Ltd.
The TNN 500AF package includes a high performance aluminum computer case with an absolutely
noiseless cooling solution that does not require the use of a fan, making it ideal for:
1. D g tal Aud o Workstat ons (DAW) in broadcasting, recording, and postproduction studio control rooms.
2. Mult Med a & Storage Servers for offices, educational facilities, and hotels.
3. Home Theater and Mult Med a Systems for living rooms.
4. H gh Performance No seless Workstat ons & Servers for SOHO (Small Office Home Office) systems.
For more information, please visit the Zalman website.
1 . TNN (Totally No Noise) Computer Case