ZALMAN CNPS7700 LED User manual

User’s Manual
CNPS7700 Series
www.ZALMAN.com
V 2.1
Intel Socket 1155/1156/775 CPUs
Core i7
Core i5
Core i3
Core 2 Quad
Core 2 Duo
Pentium Dual Core
Pentium D
Pentium 4
Celeron D
AMD Socket 754/939/940 CPUs
Athlon 64
Athlon 64 X2
Athlon 64 FX
Opteron
Dual-Core Opteron
Sempron
To ensure safe and easy installation,
please read the following precautions.

1
.COM
2. Specifications
Model
Spec.
CNPS7700-Cu
CNPS7700-Cu LED
CNPS7700-AlCu
CNPS7700-AlCu LED
Materials Pure Copper Pure Copper and
Aluminum
Weight 918g 600g
Dimensions 136(L) Ⅹ136(W) Ⅹ67(H)㎜
Fan
Bearing-Type 2 Ball-Bearing
RPM 1,000 ~ 2,000rpm ±10%
Noise Level 20 ~ 32dBA ±10%
Input Voltage 12V
Fan
Mate 2
Output Voltage 5V ~ 11V ±2%
Maximum Capacity Up to 6W
1. Precautions
1) Use and keep product away from reach of children and pets.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and
eyes. If contact is made with skin, wash off with water. If ingested or
irritation persists, seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this
product.
4) Excessive force exerted on the fan may cause damage to the fan and/
or system.
5) Avoid inserting objects or hands into the fan while it is in operation to
prevent product damage and injuries.
6) Check the components list and condition of the product before
installation. If any problem is found, contact the retailer to obtain a
replacement.
7) Zalman Tech Co., Ltd. is not responsible for any damages due to
overclocking.
8) During transportation of the system, the cooler must be removed.
Zalman is not responsible for any damages that occur during the
transport of a system.
9) Product design and specifications may be revised to improve quality
and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due
to external causes, including but not limited to, improper use,
problems with electrical power, accident, neglect, alteration,
repair, improper installation, or improper testing.

2
.COM
3. Components
S-Type Grips
L-Type Grips
User’s Manual
Thermal Grease
Clip Support
Clip Support Fixing Bolts
Washers
Nuts
AMD Backplate Backplate Fixing Bolts Washer Plate
Fan Mate 2 Cable
Fan Mate 2 Double-Sided Tape
1) Common Components
2) Intel Components
3) AMD Components
Socket 1155 / 1156 / 775
Socket 754 / 939 / 940
Cooler

3
.COM
4. Installation Requirements
1) Space Requirements
2) Compatible CPUs
The cooler’s installation requires unobstructed space with dimensions of
136㎜(width), 136㎜(height), 70㎜(depth), and the CPU as a central
reference point. Please check if components such as ODDs and PSU protrude
into the required space.
①Intel Socket 1155 / 1156 / 775 CPUs
②AMD Socket 754 / 939 / 940 CPUs
Core i7 / i5 / i3 Core 2 Quad Core 2 Duo
all clock speeds all clock speeds all clock speeds
Pentium 4 Celeron D
Prescott Cedar Mill
up to 540 up to 650 all clock speeds
Athlon 64 FX Athlon 64 X2 Athlon 64 Sempron
up to 53 up to 5600+ all clock speeds all clock speeds
136㎜
70㎜
136㎜

4
.COM
1) Intel Socket 1155 / 1156 / 775 Installation
①Install the Clip Support to the motherboard according to the socket-type.
5. Installation
②Clear off any particles or residue from the CPU’s surface then spread
a thorough layer of Thermal Grease on the CPU and the base of the
cooler.
▶Please make note of the Lever Slot’s direction when
installing the Clip Support.
Caution
Nut
Washer
Bolt(silver)
Clip Support
M/B
Socket 1155 / 1156
Socket 775
Lever
Slot

5
.COM
2) AMD Sockets 754 / 939 / 940 Installation
③Install the S-Type Grips to both sides of the Clip and fasten Bolts through
the holes of the Grips onto the Clip Support.
①Install the AMD Backplate to the motherboard using Washers and
Backplate Fixing Bolts.
Backplate Fixing Bolt
Washer
AMD Backplate
M/B
②Clear off any particles or residue from the CPU’s surface then spread
a thorough layer of Thermal Grease on the CPU and the base of the
cooler.

6
.COM
③Install the L-Type Grip to both sides of the Clip and fasten Bolts through
the holes of the Grips onto the Clip Support.
①Connect Fan Mate 2 between the
Fan Cable and the motherboard
as shown in the diagram below.
②Fan Mate 2 can be installed to the
side of the case using Double-Sided
Tape.
M/B
Fan Connector (Cooler)
Double-Sided Tape
6. Fan Mate 2 Installation and Usage
1) Fan Mate 2 Installation
2) Fan Mate 2 Operation
Adjust the Fan Speed Control
Knob for RPM control.
Fan Speed Control Knob
In the case that you get a BIOS error beep:
①Rotate the Fan Speed Control Knob clockwise to the maximum setting.
②Disable CPU Fan Detected in BIOS setting or set the system monitoring
program’s CPU Fan RPM to the lowest setting.
※Certain motherboards will not boot if the CPU fan’s RPM is not detected. In this
case inquire to the motherboard’s manufacturer for additional details.
BIOS Booting Error

7
.COM
GS1000 / GS1000SE
•E-ATX / Standard ATX / microATX Compatible
* Supports Intel Dual Xeon server motherboards
•UP to 6 Hot Swap HDD Bays
* GS1000(3 Standard / 3 Optional)
* GS1000 SE(Optional)
•Tool-Free HDD Installation
•Airflow Optimized Design
•Vibration Absorbing HDD Dampers and Feet
•The World’s First Roller Rails for Smooth
& Easy PSU Installation
•Cable Compartment Behind the Motherboard
for Cable Management
•Dedicated Fan Compartment for Fanless PSU Users
•Up to a Total of 8 HDD Bays
* 2 Adaptors & Bezels included for use of two 5.25”bays as 3.5”Internal(HDD)/
External(FDD) Bays
GT1000
•High-End Gaming Enclosure Built with Sturdy
All Aluminum Panels
•Three Tool-Free Hinged Magnetic Panels
(2 Left, 1 Right) for Easy Installation and
Access to Components
•Tool-Free Installation of Disk Drives,
Fan Controlles, Audio Interfaces etc.
•Accommodates up to 6 Hard Drives
•Luxurious and Cool Aesthetics.
•Color Option: Black (Red LED Fans),
Titanium (Blue LED Panel).
For more information, please visit our website.