ZALMAN ZM-WB5 Plus User manual

G

http://www.zalman.com
MODEL : ZM-WB5 Plus
CPU WATER BLOCK
for Higher Water Cooling Perfomance
User’s Manual
※Please read this manual thoroughly prior to installation
Ver. 1.0

1) Common Components
1
1. Precautions
2. Specifications
3. Components
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Test the product for leakage before installing it into the system. Once no leakage is confirmed, proceed with
installation and usage.
Check the components list and condition of the product before installation. If any problem is found, contact the
retailer to obtain a replacement.
Use coolant, approved for personal computer water cooling usage, mixed with distilled water to prevent corrosion.
Do not install the product if it interferes with any (motherboard) components.
To prevent leakage, this product is designed to prevent disassembly. Do not disassemble the product under any
circumstance.
Zalman is not responsible for any damages caused by overclocking.
Excessive force exerted on the product may cause critical damage to the product and/or system.
The cooler must be removed when transporting the system. Zalman is not responsible for any damages that occur
during transport of a system.
Product designs and specifications may be revised without prior notification to improve quality and performance.
Do not ingest Thermal Grease, and avoid its contact with skin and eyes. If contact is made with skin, wash off with
water. If ingested or irritation persists, seek medical attention.
①One(1) Cooler ② Two(2) Tube Clamps A
(13.8x9.5mm)
③ Two(2) Tube Clamps B
(11.5x8mm)
Weight
Materials
Dimensions
Intel
AMD
Tube Clamp A
Tube Clamp B
Compatible CPU Socker
Compatible Tubes
(Outer x Inner)
154g
Copper (base), Aluminum(case)
53(W) x 63(L) x 40(H)
Socket 1366 / 775
Socket AM3 / AM2+ / AM2 / 754 / 939 / 940
14x10mm, 13x10mm
13x9mm, 12x9mm, 12x8mm, 11x8mm, 10x8mm
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes,
including but not limited to, improper use, problems with electrical power, accident,
neglect, alteration, repair, improper installation, or improper testing.

2) Socket 1366 (Intel) Components
2
④ One(1) Thermal Grease ⑤ One(1) Paper Washer Sheet
⑦One(1) Socket 1366
Clip Support
⑧ One(1) Socket 1366 Clip
⑨ Four(4) Socket 1366 Clip
Support Fixing Bolts (Gold)
⑩ Four(4) Socket 1366
Washers
3) Socket 775 (Intel) Components
⑪One(1) Clip support(top) One (1)
Backplate (bottom) for Socket 775
⑫Two(2) Socket 775 Clip ⑬Four(4) Socket 775 Clip
Support Fixing Bolts (Silver)
⑭ Three(3) Socket 775 Clip
Fixing Bolts (Silver)
⑮ Three(3) Socket 775 Clip
Assembly Bolts (Gold)
4) Socket AM3 / AM2+ / AM2 / 754 / 939 / 940 (AMD) Components
⑯One(1) AMD Clip
⑥ One(1) User’s Manual

1) Pre-Installation Verification
Make sure to install the cooler so that the outlet is placed above the inlet, as shown in the diagram.
2-Ⓐ) Installation on Intel Socket 1366
①Align the Intel Socket 1366 Clip Support with the motherboard installation holes and secure
with Socket 1366 Clip Support Fixing Bolts (Gold).
3
4. Installation
Top
Bottom
Outlet
Socket 1366 Clip Support
Socket 1366 Washer
Socket 1366 Clip Support
Fixing Bolt (Gold)
Inlet
Motherboard
Socket 1366 Clop Support Fixing Bolts(Gold) must be used. Installation using the
Socket 775 Clip Support Fixing Bolts(Silver) can cause damage to the Socket 1366
Clip Support.
Caution

4
③Cover the CPU with the cooler, and fix by tightening the bolts on the Clip onto the Clip Support.
2-Ⓑ) Installation on Intel Socket 775
①Align the Socket 775 Clip Support (top) and Backplate (bottom) with the motherboard installation
holes and secure with Socket 775 Clip Support Fixing Bolts (Silver).
Socket 775 Clip Support
Fixing Bolt (Silver)
Socket 775 Clip Support
(top)
Socket 775 Backplate
(bottom)
Motherboard
②Clear off any particles or residue from the CPU’s surface then spread (outwards from center) a
thin but thorough layer of Thermal Grease on the CPU and the base of the cooler.

5
②Secure the Intel Socket 775 Clip to the Cooler with the Intel Socket 775 Clip Fixing Bolts (Silver).
④Set the CPU Water Block at the center of the CPU and secure the Cooler with the Socket 775
Assembly Bolts (Gold) to the Clip Support.
Please take extra care to align the
attachment holes of the Two (2) Socket
775 Clips.
③Clear off any particles or residue from the CPU’S surface then spread (outwards from center)
a thin but thorough layer of Thermal Grease on the CPU and the base of the cooler.
Caution

6
2-Ⓒ) Installation on AMD Socket AM3 / AM2+ / AM2 / 754 / 939 / 940
Set the CPU Water Block at the center of the CPU and hook the flat side of the clip onto the
motherboard clip support. Complete installation by exerting downward force on the levitated side
of the Clip until both sides are hooked and fastened.
3) Tube Connection
Use a pair of wire pincers or pliers to unfasten the Tube Clamps, and insert the Tubes. Connect and
fasten to the cooler as shown in the diagram.
▶Please refer to the Pre-Installation Verification on Page 3 to prevent the reversal of the
Inlet and Outlet Tube Connections.
▶
Please make sure to use compatible Tube Clamps for the tube’s diameter and
adjust the insertion depth accordingly.
▶Please test run the pump after installation to ensure proper operation.
Tube Clamp A
(13.8 x 9.5mm)
14 x 10mm, 13 x 10mm
Tube Clamp B
(11.5 x 8mm)
13 x 9mm, 12 x 9mm, 12 x 8mm
11 x 9mm, 11 x 8mm
Caution

7
Gaming PC Enclosures
For more information, please visit our website.
•High-End Gaming Enclosure Built wit Sturdy All
Aluminum Panels
•Three Tool-Free Hinged Magnetic Panels (2 Left, 1 Right)
for Easy Installation and Access to Components
•Tool-Free Installation of Disk Drives, Fan Controlles,
Audio Interfaces etc.
•Accommodates up to 6 Hard Drives
•Luxurious and Cool Aesthetics.
•Color Option: Black (Red LED Fans),
Titanium (Blue LED Panel)
GS1000 / GS1000SE
GT1000
•E-ATX / Standard ATX / microATX Compatible
✽Suppotrs Intel Dual Xeon server motherboards
•UP to 6 Hot Swap HDD Bays
✽GS1000(3 Standard / 3 Optional) / GS1000 SE(Optional)
•Tool-Free HDD Installation
•Airflow Optimized Design
•Vibration Absorbing HDD Dampers and Feet
•The World’s First Roller Rails for smooth & Easy PSU Installation
•Cable Compartment Behind the Motherboard for Cable Management
•Dedicated Fan Compartment for Fanless PSU Users
•Up to a Total of 8 HDD Bays
✽2 Adaptors & Bezels included for use of two 5.25〞bays as 3.5〞Internal(HDD) /
External(FDD) Bays