ZALMAN CNPS9700 LED User manual

User’s Manual
CNPS9700 LED
www.ZALMAN.com
V 2.0
Intel Socket 1156/775 CPU
Core i7
Core i5
Core 2 Quad
Core 2 Duo
Pentium Dual Core
Pentium D
Pentium 4
Celeron D
AMD Socket AM3/AM2+/AM2/754/939/940 CPU
Phenom Ⅱ
Phenom
Athlon ⅡX2
Athlon
Athlon 64
Athlon X2
Athlon 64 X2
Athlon FX
Athlon 64 FX
Opteron
Dual-Core Opteron
Sempron
To ensure safe and easy installation,
please read the following precautions.

1
.COM
2. Specifications
Model
Spec. CNPS9700 LED
Material Pure Copper, Aluminum
Weight 764g
Dimensions 90(L) Ⅹ124(W) Ⅹ142(H)㎜
Fan
Bearing-Type 2 Ball-Bearing
RPM 1,250 ~ 2,800rpm ±10%
Noise Level 19.5 ~ 35dBA ±10%
Input Voltage 12V
Fan
Mate 2
Output Voltage 5 ~ 11V ±2%
Maximum Capacity Up to 6W
ZM-STG1
Net Weight 3.5g
Temp Range -40 ~ 150℃(-40 ~ 302℉)
1. Precautions
1) Use and keep product away from reach of children and pets.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and
eyes. If contact is made with skin, wash off with water. If ingested or
irritation persists, seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this
product.
4) Excessive force exerted on the fan may cause damage to the fan and/
or system.
5) Avoid inserting objects or hands into the fan while it is in operation to
prevent product damage and injuries.
6) Check the components list and condition of the product before
installation. If any problem is found, contact the retailer to obtain a
replacement.
7) Zalman Tech Co., Ltd. is not responsible for any damages due to
overclocking.
8) During transportation of the system, the cooler must be removed.
Zalman is not responsible for any damages that occur during the
transport of a system.
9) Product design and specifications may be revised to improve quality
and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due
to external causes, including but not limited to, improper use,
problems with electrical power, accident, neglect, alteration,
repair, improper installation, or improper testing.

2
.COM
1) Common Components
3. Components
Clip Support Fixing Bolts
AMD Clip LeverAMD Clip
Clip Support
User’s Manual
Washers Nuts
Intel Clip
Clip Fixing Bolts
Cooler
2) Intel Components
3) AMD Components
Thermal Grease
Fan Mate 2 Cable
Fan Mate 2 Double-Sided Tape

3
.COM
4. Installation Requirements
1) Space Requirements
2) Air Guide Removal
3) Cooler Orientation
The cooler’s installation requires unobstructed space with dimensions of 127㎜
(width), 93㎜(length), 145㎜(height), and the CPU as a central reference point.
Please check if components such as ODDs and PSU protrude into the required
space.
Air guides on enclosures must be removed, before the cooler’s installation, for
they protrude into the cooler’s required space.
It is recommended that the cooler be installed so that air flows from the cooler toward
the enclosure’s rear exhaust fan.
93㎜
145㎜
127㎜
PSU

4
.COM
4) Installation Based On Clip Orientation
A. Horizontal Clip Orientation
B. Vertical Clip Orientation

5
.COM
②Remove any foreign particles from the Base of the the cooler and the
surface of the CPU, then shake well the enclosed thermal grease and
apply a through layer of thermal grease on the surface of the CPU and
the Base of the cooler.
1) Intel Socket 1156 / 775 Installation
①Install the Clip Support to the motherboard according to the socket-type.
5. Installation
Nut
Washer
Bolt(silver)
Clip Support
M/B
Socket 1156
Socket 775
▶Please make note of the Lever Slot’s direction when
installing the Clip Support.
Caution
Lever
Slot

6
.COM
④Refer to Section 6 ‘Fan Mate 2 Installation and Usage’for instructions on
power connection.
③Insert a Bolt into both ends of the Intel Clip, then screw each Bolt a little
at a time, alternating between each Bolt, until the Clip is fully installed.
2) AMD Socket AM3 / AM2+ / AM2 / 754 / 939 / 940 Installation
①Remove any foreign particles from the Base of the the cooler and the
surface of the CPU, then shake well the enclosed thermal grease and
apply a through layer of thermal grease on the surface of the CPU and
the Base of the cooler.
▶For installations with horizontal Clip
orientation, please be cautious to
not exert excessive force on the fan
while using a screwdrivers to install
the Clip.
Caution

7
.COM
③Refer to Section 6 ‘Fan Mate 2 Installation and Usage’for instructions on
power connection.
①Connect Fan Mate 2 between the
Fan Cable and the motherboard
as shown in the diagram below.
②Fan Mate 2 can be installed on the
side of the case using Double-Sided
Tape.
M/B
Fan Connector (Cooler)
Double-Sided Tape
6. Fan Mate 2 Installation and Usage
1) Fan Mate 2 Installation
②Insert the AMD Clip Lever into the AMD Clip’s Clip Lever Slot, then hook
the opposite end on its Lug, press down on the Clip Lever and hook it
onto its Lug.
Lug

8
.COM
GS1000 / GS1000SE
•E-ATX / Standard ATX / microATX Compatible
* Supports Intel Dual Xeon server motherboards
•UP to 6 Hot Swap HDD Bays
* GS1000(3 Standard / 3 Optional)
* GS1000 SE(Optional)
•Tool-Free HDD Installation
•Airflow Optimized Design
•Vibration Absorbing HDD Dampers and Feet
•The World’s First Roller Rails for Smooth
& Easy PSU Installation
•Cable Compartment Behind the Motherboard
for Cable Management
•Dedicated Fan Compartment for Fanless PSU Users
•Up to a Total of 8 HDD Bays
* 2 Adaptors & Bezels included for use of two 5.25”bays as 3.5”Internal(HDD)/
External(FDD) Bays
GT1000
•High-End Gaming Enclosure Built with Sturdy
All Aluminum Panels
•Three Tool-Free Hinged Magnetic Panels
(2 Left, 1 Right) for Easy Installation and
Access to Components
•Tool-Free Installation of Disk Drives,
Fan Controlles, Audio Interfaces etc.
•Accommodates up to 6 Hard Drives
•Luxurious and Cool Aesthetics.
•Color Option: Black (Red LED Fans),
Titanium (Blue LED Panel).
For more information, please visit our website.
2) Fan Mate 2 Operation
Adjust the Fan Speed Control
Knob for RPM control.
Fan Speed Control Knob
In the case that you get a BIOS error beep:
①Rotate the Fan Speed Control Knob clockwise to the maximum setting.
②Disable CPU Fan Detected in BIOS setting or set the system monitoring
program’s CPU Fan RPM to the lowest setting.
※Certain motherboards will not boot if the CPU fan’s RPM is not detected. In this
case inquire to the motherboard’s manufacturer for additional details.
BIOS Booting Error