ZALMAN Z9 series User manual

SERIES
English / 한글 / Français / Español
ATX Mid Tower PC Case Z9 series
Ver.130709

Z9D
Ⅰ
Z9 / Z9 Plus
Z9D
Ⅲ
Z9D
Ⅱ
Z9D
Ⅳ
ENG) Front Bezels differ by model.
KOR) 전면 베젤은 모델명에 따라 다를 수 있습니다.
FRA) La façade avant peut différer en fonction du modèle.
ESP) El bisel frontal se puede ser diferente dependiendo del modelo.

1
1
ENG
Z9 Series
1) Please read this manual thoroughly prior to installation.
2) Before installing, check the components and condition of the product,
and if any problem is found, contact the retailer.
3) Avoid inserting objects or hands into the system while it is in operation
to prevent product damage and injuries.
4) Check the manual when connecting cables. Incorrect connections
may cause short circuits leading to 󰘰re hazards.
5) Do not block the front intake vent or the rear exhaust vent.
6) Keep this unit away from heat sources, direct sunlight, water, oil, and
humid environments, and place the unit on a 󰘱at, stable, vibration-free,
and well-ventilated area.
7) Do not clean the product surface with chemicals or wet cloth.
(chemicals: industrial brightener, wax, benzene, alcohol, paint thinner,
mosquito repellent, aromatics, lubricant, detergent etc.)
8) Please wear gloves while handling this product to prevent injuries.
9) Product design and speci󰘰cations may be revised to improve quality
and performance.
The diagrams used in this manual are based on model Z9 Plus. Installation
for the Z9 , Z9D series follows the exact installation procedure.
Cautionary Notes
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages
due to external causes, including but not limited to, improper
use, problems with electrical power, accident, neglect,
alteration, repair, improper installation, or improper testing.

2
Z9 Series
2Product Details
(1) Speci󰘰cations
Models Z9 Series
Type ATX Mid Tower
Dimensions (W×H×D) 207 × 464 × 504㎜ (8.1 × 18.2 × 19.8”)
Materials Plastic, Steel
Color Black
Motherboard Compatibility Standard ATX / m-ATX
Power Supply Compatibility Standard ATX / ATX12V
PCI/AGP Compatibility Full Size 290㎜ (11.4")
Drive Bays
5.25” External Bay x 3
3.5“ External Bay x 1, Internal Bay x 5
5.25"/3.5"/2.5” 1 (3in-1)
Hot-swap -
Expasion Card Solts 7 Slots
Cooling
Components
Front 120mm/140mm Fan Vent x 1 (1 Fan included)
Top
Z9 Plus /
Z9D Series
120mm/140mm Fan Vent x 2
(1 Fan included, 1 optional)
Z9 120mm/140mm Fan Vent x 2
(Fans optional)
Bottom 120㎜ or 140㎜ Fan × 1(Optional)
Rear 120mm/140mm Fan Vent x 1 (Fan optional)
Side
Z9 Plus /
Z9D Series
120mm Fan Vent x 2
(1 Blue LED Fan included, 1 optional)
Z9 120mm Fan Vent x 2
(Fans optional)
Front Panel
I/O Port
Z9 Plus /
Z9D Series
Headphones x 1, Mic x 1, Fan controller,Temperature display
USB 2.0 x 4 ( or USB 2.0 x 2 / USB 3.0 x 2)
Z9 Headphones x 1, Mic x 1, USB 2.0 x 4
※ USB3.0 port is available as option by model.

3
ENG
Z9 Series
(2) Product Information
Front Top Side (left)
(3) Front Panel I/O Ports
Mic
Headphones
HDD LED
Reset Button
USB 2.0
USB 2.0 USB 2.0
RESET
HDD
MIC HEADPHONE
USB 2.0
(or USB 3.0)
Power Button
Temperature Display
Fan Controller
※ Temperature and Fan Controller display are only available on the Z9 Plus, Z9D Series.

4
Z9 Series
(4) Parts
Cable Tie × 5 CPU 12V Extension Cable × 1
Stand-O󰘯 × 5Main Unit
A Bolt (#6-32*6mm) × 11
[PSU, PCI]
B Bolt (M3*5mm) × 17
[M/B, FDD, SSD]
D Bolt (#6-32*4mm) × 20
[3.5” Bay HDD]
C Bolt (M3*6mm) × 12
[5.25”Bay ODD]
HDD Anti-static rubber × 20
[3.5” Bay HDD]
User’s Manual
E Bolt (#6-32*6mm) × 5
[3.5” HDD]

5
ENG
Z9 Series
Installation
(1) Side Panel Removal
3

6
Z9 Series
(2) PSU Installation
A Bolt
▶ Type A (PSU independent cooling)
If the PSU’s fan points downwards, the PSU’
s cooling performance is enhanced.
▶ Type B (Case Air Circulation Type)
If the PSU’s fan points inwards, the PSU’s
cooling performance is enhanced.
※ When using the case in a dusty environment, use Type B.
Tip

7
ENG
Z9 Series
(3) Motherboard Installation
ATX Board
or
m-ATX Board
There are 4 Stand O󰘯s preinstalled. Please refer to the diagrams below for
additional Stand O󰘯 positions (based on motherboard type).
Stand-O󰘯
B Bolt

8
Z9 Series
(4) VGA Card Installation
(5) 5.25” and 3.5” Drive Installation
PULL
1) Front Cover Removal
A Bolt

9
ENG
Z9 Series
② Attach Drive to Tray
A. 3.5” FDD Installation
3.5” FDD
3.5” FDD
B Bolt
When fastening the Tray, Type A Bolts must be used.
Caution
2) ODD Installation
3) 2.5” / 3.5” Tray Installation
① Tray Removal
C Bolt

10
Z9 Series
B. 3.5” HDD Installation
3.5” HDD
3.5” HDD
C. 2.5” SSD Installation
SSD
SSD
(6) Front Cover Installation
A Bolt
B Bolt
When removing the front cover, the power switch and extension
cable are separated to prevent disconnection. Be sure to
connect them before installing the front cover.
Caution

11
ENG
Z9 Series
(7) 3.5” HDD Installation
HDD
HDD
HDD
HDD
HDD
Tip
The HDD can be installed in 2 di󰘯erent directions, according to your desired
Cable Management style.
A Type B Type
1) Installation of HDD Anti-static rubber and Bolt
2) HDD Installation
HDD Anti-static
rubber
Push into the 3.5” Bay until a “click” sound is heard.
D Bolt

12
Z9 Series
3) HDD Removal
When removing HDD, pull the fastening lever outwards and then remove it.
Tip
When transporting an assembled system, please secure the HDD with
Bolt E as shown above.
E Bolt

13
ENG
Z9 Series
1) Power Button Cable
(9) Cable Connection
Power LED Power
Motherboard
Power Button
or
(8) SSD Installation
SSDs can be installed on the right side of case as shown in the diagram below.
B Bolt

14
Z9 Series
② Fan Control, Temperature Display connection
▶ Fan Controller: After connecting the 4-Pin Power cable, connect Fans
to Fan Connector.
▶ Temperature Display: After connecting 4-Pin Power, locate temperature
sensor in desired location. (The sensor is for the case’s internal
temperature readings.)
Fan Controller Temperature Display
PSU Power PSU Power
Temperature
Sensor
Fan Fan
2) Front Panel I/O Port Cable
Motherboard
Front Panel I/O Port
Tip
▶ To connect USB 2.0 audio cables, please refer to the motherboard manual.
▶ When the +/- polarities are reversed, the LED’s will not function.
▶ USB3.0 port is available as option by model
① Front Panel I/O Port connection
HD Audio
Audio
USB 2.0 USB 3.0 or USB 3.0 Reset HDD LED

15
ENG
Z9 Series
2) Top Panel Fan (120/140 mm) Installation
When installing fan, press the Top Panel’s eight Hook’s towards each other to
remove and install as shown in diagram below. The Z9 Plus comes with one
120mm Fan pre-installed.
(10) Optional Fan Installation and Replacement
The Z9 Plus comes with one 120mm Side Panel Fan pre-installed.
1) Optional Side Panel Fan (120mm) Installation

16
Z9 Series
3) Front Panel Fan (120/140mm) Replacement
One 120mm Fan is pre-installed.

한 글

1
1
ENG
Z9 Series
1) 설치 전 제품 설명서를 반드시 숙독하시기 바랍니다.
2) 설치 전 구성품 및 제품의 상태를 반드시 확인하시고 이상이 있을 경우 구
입처에 상담하시기 바랍니다.
3) 동작중인 제품에 손이나 물체를 넣지 마십시오. 인체 및 제품에 해를
끼칠 수 있습니다.
4) 케이블을 연결할 때 반드시 매뉴얼을 확인한 후 연결하십시오.
잘못 연결할 경우 합선으로 인한 화재의 우려가 있습니다.
5) 제품의 전면과 후면에 있는 통풍구가 막히지 않도록 주의 하십시오.
6) 직사광선이 들어오는 곳이나 난방기 주변 등 열이 발생하는 곳,
물(빗물)이 튀는 곳, 기름 및 습기가 많은 곳을 피하여 공기가
잘 통하고, 평탄하며 진동이 없는 곳에 설치하십시오.
7) 화학약품과 물 걸레 등으로 제품표면을 닦지 마십시오. (화학약품,
공업용 광택제, 왁스, 벤젠, 알코올, 신나, 모기 약, 방향제, 윤활제, 세정제
등)
8) 잘못 설치하여 발생되는 문제에 대해서 당사는 책임지지 않으므로
반드시 설명서를 참조하여 설치해 주시기 바랍니다.
9) 정해진 용도 이외의 사용으로 인하여 발생하는 문제에 대하여
당사는 어떠한 책임도 지지 않습니다.
10) 본 제품 취급도중 상처 및 사고예방을 위해 장갑을 반드시 착용하여
주십시오.
11) 제품의 외관디자인 및 규격은 제품의 품질향상을 위하여 소비자에게 예고
없이 변경될 수 있습니다.
본 매뉴얼의 설치방법에 사용된 그림은 Z9 Plus 기준이며 Z9과 Z9D
Series 설치방법은 동일합니다.
주의사항 한글