Zap TX-1 User manual

TX-1 VIBRATION TRAINER
Please read this Manual carefully prior to the use and properly
maintain it.
Operating Manual

To reduce risk of injury, the user must read and understand this instruction manual
before using the Vibration Plate Slim. This machine is intended for home use only
in accordance with the instructions provided in this manual.
Please read these instructions carefully and retain for future use.
IMPORTANT SAFETY INSTRUCTIONS
• Not suitable for children or pregnant woman!
• Use for the intended purpose only.
• Only use inside, only use in dry environment.
• Do not use if the product is damaged.
• Do not jump on the plate or the machine.
• Place the device only on a solid, level, and moisture-resistant surface.
• After use, the machine must be switched off and unplugged.
• Do some warming-up exercises before start using the machine.
• Increase speed intensity and duration of exercises gradually.
• Only one person is allowed to use the machine at one time.
• Consult your doctor immediately when you feel: sick, experience pain in
joints or other locations, aches abnormal heartbeat rate or any other
abnormal symptoms.
• If you have not done any sport for a long time or if you have a heart problem,
neurologic problem, circulatory disturbances or orthopedic problems, you
should first consult your doctor before operate this machine.
• Stop using the machine immediately if you feel tired, uncomfortable or dizzy.
• This appliance is not intended for use by persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.

WARNING: Before beginning any exercise programme, consult your physician.
This is especially important for persons with pre-existing health problems. The
seller assumes no responsibility for personal injury or property damage sustained
by or through the use of this product.
MEDICAL RECOMMENDATIONS: You MUST NOT use the Vibration Machine
without your doctor’s consent if you:
• Are pregnant
• Have had a recent operation or surgery
• Have knee, shoulder, back or neck injuries
• Retinal condition
You are strongly recommended to consult your doctor before using the Vibration
Machine if you have any of the following:
·Heart condition or cardiovascular
disease
·High blood pressure
·Acute thrombosis
·Acute hernia
·Severe diabetes
·Epilepsy
·Severe migraines
·Malignant tumour
·Pacemaker, metal implant,
artificial joint(s) or limb(s), stents
or IUDs, metal plates or pins
·Any recent illnesses or infections
·Deep Vein Thrombosis
·Cancer
PRODUCT SPECIFICATIONS
User Weight Capacity:
120kg
Dimensions:
533 x 414 x 120mm
Shipping Weight:
12kg
Net Weight:
9.5kg
Power Requirements:
110V
Rated Frequency:
60Hz
Power:
300W

ASSEMBLY INSTRUCTIONS
STEP 1
—Choose a suitable place for your vibration machine. Leave yourself at
least 1 metre of space either side of the machine to avoid injury. Place the
machine on a solid, flat level surface with a suitable cover for your floor or
carpet.
—Insert 2 x AAA Alkaline batteries into the remote control unit.
STEP 2
Roller
—There is a roller on the underside of the right hand edge of the machine,
as you look at the display. Hold the left hand side of the machine and lift to
a 45° angle. Then use the roller to position the machine into the optimal
spot for your workout.
STEP 3
Resistance Bands
—Attach the resistance bands by locating the metal arm underneath the
machine. Move it out so the arm is pointing out from underneath the disc.
Loosen the carabiner lock (if required) on the end of the resistance band,
clip it through the hole at the end of the metal bar, then screw the lock on
the carabiner clip in place.
Note: Make sure that the carabiner clip is fastened by screwing the lock in
place, to ensure the clip does not come loose during use.
Adjusting Resistance Bands
—If you find you need to adjust the length of
your resistance band, take Part A in one
hand and start to thread through the band
from underneath. This should create a small
loop at point B. Pull point D away from Part A
(whilst keeping hold of Part A) so that the
loop disappears. This will shorten the length
of the resistance band overall.
—To lengthen your resistance band, thread a
small amount of band through Part A as
before to create a loop at point B. Then pull
the band at point C so that the handle moves
towards Part A. This should increase the loop
and now you will need to thread the loop
through Part A so it disappears.
Note: When not in use please ensure resistance bands are stored away safely
so they are not a potential trip hazard.

USING THE TRAINER
Control Panel
Remote Control
Functional description
1. Plug the Vibration trainer into the mains power socket, switch on the red power
switch which located at the back of the machine. The LED will display Program
Code for a second, then the LED will fully display for a second and then beep to
indicate that the panel is in the standby mode. And LED will display “----”.
2.In standby mode ,press the ON/OFF button on the remote control or START on
the control panel, and the trainer will start running. This is a manual mode which
starts at speed 1 for 10 minutes.
3.To stop the Trainer when it is in use press the ON/OFF button on the remote
control or the STOP button on the control panel The trainer will then go into standby
mode.
4.By pressing the P(Program) button on the control panel you can choose different
workouts. P1, P2, P3 are the auto modes, and the workout times are 10 minutes.
See chart below.
5.When in manual mode you can adjust the time from 1-20 minutes by pressing the
TIME button. The speed can be adjusted from 1 to 20 by pressing “+/-“ key. On the
remote control there are quick access speed buttons LOW, MID, HIGH. Low speed
is 5, mid speed is 10 and high speed is 15.
6.When in the AUTO programs mode the speed cannot be adjusted by using the
keys mentioned in point 5.
PROG TIME
SPEED
SPEED
STOP
START
P1
P2
P3

AUTO Mode P1,P2,P3.
10-9
9-8
8-7
7-6
6-5
5-4
4-3
3-2
2-1
1-0
2
4
6
8
10
12
14
16
10
6
1
2
3
4
5
6
14
10
8
6
4
10
4
10
4
16
4
16
4
10
TIME(Minutes)
TIME(Minutes) P1(SPEED) P2(SPEED) P3(SPEED)

CARE AND MAINTENANCE
Before cleaning or carrying out any maintenance on your vibration machine,
ensure the power is turned off and the power cord removed from the plug socket.
Cleaning
Clean your vibration machine with a damp cloth and mild detergent only,
immediately after use. Use a weak solution of anti-bacterial washing up liquid in
warm water and a microfibre cloth. Be sure to wring out the cloth so that it is just
damp.
Storage
Regularly check the cord/cable for damage before storing. Should the cord/cable
be damaged in any way it must ONLY be replaced by an identical cable of the
same type and specification. Never pull the cord/cable to disconnect from the
power outlet. Always grasp the plug and pull to disconnect. Remove the plug when
not in use and store on its feet at all times.
Troubleshooting
—No lights; does not respond to Control Panel or Remote Control.
Check machine is plugged in and switched on at the mains. Check socket
works with an alternative electrical product. Replace fuse in plug.
—Remote Control does not operate machine, but unit does respond to Control
Panel.
Point Remote Control transmitter directly at the Control Panel’s sensor.
Replace batteries in remote control (2 x AAA alkaline batteries are required).
—Speed too fast!
Adjust speed using the speed buttons on the Remote Control or the Control
Panel.

Distributed globally by
UK & Europe
Shop 247
Units 3 & 4 Lower Park Farm
Storrage Lane
Alvechurch, Worcestershire B48 7ER
United Kingdom
Telephone: [phone]
USA – West Coast
Shop247.com Inc
Suite 110-120
16 Sunset Way
Henderson, Nevada 89014
Telephone: [phone]
USA – East Coast
Shop247.com Inc
6965-K Northpark Blvd,
Charloe,
North Carolina 28216
Telephone: [phone]