zarges Z 600 S-PLUS Parts list manual

Assembly and usage instructions
Z 600 S-PLUS scaffold towers

Assembly and usage instructions

Assembly and usage instructions Assembly and usage instructions 3 Assembly and usage instructions 3
Table of contents
1. General information 4
1.1. Introduction 4
1.2. Manufacturer 4
1.3. Type approval 4
1.4. Warranty 4
1.5. Date of issue 5
1.6. Copyright and trademark rights 5
1.7. Intended use 5
1.8. Improper use 5
2. Setup 6
2.1. Safety provisions 6
2.2. Usage regulations 7
2.3. Working on electrical units with the scaffold tower 8
2.4. Other applicable safety instructions 8
2.5. Technical data 9
2.6. General assembly regulations 10
2.7. Note on dismantling the scaffold tower 12
2.8. Basic dimensions 13
2.9. Identification 14
2.10. Parts list incl. ballast (see also 3.2) 15
2.11. Position of the individual parts 17
2.12. Assembly drawings 18
3. Structural safety regulations 34
3.1. General information 34
3.2. Attaching the ballast 34
3.3. Attaching the anti-twist device 34
3.4. Maintenance, servicing, storage and cleaning 34
3.5. Testing the scaffold components 35
4. Spare parts 36
Notes 38

Assembly and usage instructions
4
1. General information
1.1. Introduction
These assembly and usage instructions apply exclusively to the scaffold towers
described therein.
The instructions on safety and the rules and ordinances for the handling of scaffolding
in these assembly and usage instructions lie within the area of validity of the scaffold towers
referred to in this documentation.
Operators bear sole responsibility for:
• ensuring adherence to the local, regional and national regulations,
• observance of the regulations (laws, ordinances, guidelines etc.) for safe handling
listed in the assembly and usage instructions,
• ensuring that the assembly and usage instructions are available to operating personnel
and that the instructions, information, warnings and safety provisions they contain are
followed to the letter.
1.2. Manufacturer
The manufacturer of the scaffold towers described in this documentation is
ZARGES GmbH Tel.: +49 8 81 / 68 71 00
Access Technology Division Fax: +49 8 81 / 68 72 95
PO Box 16 30 E-mail: [e-mail]
82360 Weilheim Internet: http://www.zarges.de
1.3. Type approval
The scaffold towers referred to hereafter have been tested by
1.4. Warranty
The scope and period of the warranty type are defined in the manufacturer's sales and delivery
conditions. The assembly and usage instructions valid at the time of delivery (see Section 1.5)
apply to all warranty claims arising from insufficient documentation. The following applies above
and beyond the sales and delivery conditions: The manufacturer accepts no liability for damage
to the scaffold towers provided which is caused by one or more of the following:
• Ignorance of or failure to observe these assembly and usage instructions
• Insufficiently qualified or instructed operating personnel
• Failure to use original spare parts.
The operator bears sole responsibility for ensuring
• that the safety provisions as defined in Section 5 are adhered to,
• that improper use (see Section 1.8), incorrect assembly and setup and unauthorised
operation of the scaffold towers are ruled out and
• that above and beyond this, intended use (see Section 1.7) is ensured and that the
scaffold towers are operated in accordance with the application conditions defined in
the contract.

Assembly and usage instructions Assembly and usage instructions 5
1.5. Date of issue
The date of issue of these English assembly and usage instructions is 01 Februar 2014.
1.6. Copyright and trademark rights
• The copyright to these assembly and usage instructions lies with the manufacturer.
• The manufacturer also reserves all further rights, in particular in the case of the
granting of a patent or utility patent registration.
• Any infringement of the conditions described above will result in liability for damages!
1.7. Intended use
The scaffold towers listed in these assembly and usage instructions may only be used as
scaffolding in accordance with the stipulations of EN 1004 and the overview of models in these
assembly and usage instructions.
1.8. Improper use
Misuse - that is, any use of the scaffold towers documented in these assembly and usage
instructions which deviates from that described in Section 1.7 - shall be deemed improper use as
defined by the Product Safety Act (status 1.8.1997). This also applies to disregard of the standards
and guidelines listed in these assembly and usage instructions.

Assembly and usage instructions
6
2. Setup
2.1. Safety provisions
1. The stipulations of EN 1004 “Mobile work platforms” apply to the structural safety,
erection and use of the aforementioned scaffold towers.
2. The scaffold towers may only be set up and used by persons familiar with these
assembly and usage instructions.
3. At least two persons are required to set up or dismantle the scaffold tower. (Applies to
all mobile scaffold towers with a platform height exceeding 2.50m)
4. Undamaged and fault-free original spare parts for
the manufacturer's scaffolding system to which the
test certificate applies must be used. Before using the
scaffold tower, all parts must be examined for correct
assembly and functionality.
5.
max.
12,0 m
max.
8,0 m
Under EN-1004, the maximum platform height is 8 m in
outdoor use and 12 m in completely enclosed spaces. The
maximum platform height for the scaffold towers described in
these assembly and usage instructions is 10 m in completely
enclosed spaces.
6. The use of lifting tackle on the scaffold tower is not permissible.
7. The platforms are each set up with a rung spacing of 7 rungs, afford to be granted to
the secure footing at all times.
8. The scaffold tower may only be set up in vertical position on a horizontal, level surface
of sufficient load-bearing capacity. Where necessary, load-distributing pads must be
used.
9. Chassis beams, ballast weights, stabilisers and stand-off brackets must be used to
ensure structural safety as described in these assembly
and usage instructions.
10. Working on the work platform is only permissible with
full protection on 3 sides, i.e. guard-rail frame, knee
protection and peripheral toeboards. Toeboards are not
necessary on the rest platforms.
11. Working on several work platforms simultaneously is prohibited.
12. When setting up the scaffold tower alongside a wall, stand-off
brackets (accessories, Order No. 42920) can be used in addition to
ballast.
Stop

Assembly and usage instructions Assembly and usage instructions 7
13. The maximum load-bearing capacity of the scaffold tower with an evenly distributed
load is 2.0 kN/m² (in accordance with EN 1004 - scaffolding category 3).
14. There must be no persons, tools or material on the
platform when the scaffold tower is moved. Any impact
must be avoided. The scaffold tower may only be moved
manually, in longitudinal or diagonal direction and on
afirm, level installation surface which is free of obstacles.
The scaffold tower must not be moved at more than
normal walking speed.
15. Vehicles (e.g. fork lifts) must not be used to move the scaffold tower. The scaffold tower
must not be lifted, pulled or pushed using a fork lift.
16. The surface on which the scaffold tower is moved must be capable of bearing its
weight.
17. Where the scaffold tower is used outdoors or in open
buildings, it must be moved to a wind-sheltered position or
secured against tipping over by other suitable means (e.g.
anchors) at wind strengths exceeding 6 (on the Beaufort
scale), at the onset of a storm and when finishing work for
the day. At wind speeds exceeding 6 on the Beaufort scale
(12m/s), it becomes perceptibly difficult to walk forwards.
18. The use of planks etc. to bridge gaps between scaffolding
and buildings is not permissible. The scaffold tower must
not be used as a stair tower to reach other constructions.
19. Before using the scaffold tower, check that it is in vertical position and correct its
alignment if necessary. The scaffold tower must also be checked for correct and
complete setup as described in Section 2.8.
6

Assembly and usage instructions
8
2.2. Usage regulations
1. Personnel must always climb to the work platform from
the inside of the tower.
2. Personnel must not brace themselves against the side
protection when working.
3. Jumping on the platforms is prohibited.
4. Horizontal loads which could cause the scaffold tower to
tip over must not be generated, for example by working on
adjacent constructions.
5. Particular attention must be paid to the wind conditions when using the scaffold
towers next to uncovered buildings or building corners to prevent the scaffold towers
tipping over.
6. Using ladders, crates or similar means to increase the height of the platform is
prohibited.
7. Tools and materials may only be handed upwards. Always take the weight of tools
and materials into consideration to avoid overloading the work platform. The person
handing the load upwards must not let go of it until the person receiving it has a firm
hold on it.
8. Scaffold towers with swivel castors can be moved to their final location after assembly
(the ground or floor must not slope by more than 3 %). Any impact must be avoided.
When the scaffold tower is in its final position, the alignment must be checked again.
9. When moving the scaffold tower, always take care that it does not touch any live
equipment.
10. Electrical tools (drills etc.) may only be operated on the scaffold tower at Safety Extra
Low Voltage (48 V), with protective insulation (separation transformer) or if they are
connected with a ground fault circuit interrupter with a residual current of 30 mA.
Thestipulations of BGI 594 (formerly ZH 1/228) must be complied with.
11. Tools and materials must be stored on the work platform in such a way that there is a
passageway of 20 cm at the sides of the work platform.
2.3. Working on electrical units with the scaffold tower
The scaffold tower must not be used to perform work on or in the vicinity of unprotected live
units unless
• the section of the unit in question has been disconnected,
• the section of the unit in question has been secured against being switched back on,
• the section of the unit in question has been checked to ensure that it is not live,
• the section of the unit in question has been short-circuited with a grounding bar and
• the section of the unit in question has been shielded against adjacent live parts.
2.4. Other applicable safety instructions
The scaffold tower must be tested, set up and used in accordance with the stipulations of
• BGI 663 (employers' liability insurance association, building construction) " Instructions
for handling work and safety scaffolds."
BGR 165 and BGI 594 (formerly ZH 1/228) "Safety rules for the use of electrical equipment in the
case of increased electrical hazard" apply when using electrical equipment on the scaffold tower.

Assembly and usage instructions Assembly and usage instructions 9
2.5. Technical data scaffold tower normal 0.75 m x 1.8 m / 2.5 m / 3.0 m
Approved in accordance with EN 1004 Scaffolding category 3
Permissible load in accordance with scaffolding category 3 200 kg/m²
Total maximum load for the scaffold tower 202 kg / 286 kg / 346 kg
Maximum platform load 404 kg / 572 kg / 692 kg
Maximum platform height 13.20 m
Technical data scaffold tower wide 1.35 m x 1.8 m / 2.5 m / 3.0 m
Approved in accordance with EN 1004 Scaffolding category 3
Permissible load in accordance with scaffolding category 3 200 kg/m²
Total maximum load for the scaffold tower 202 kg / 286 kg / 346 kg
Maximum platform load 404 kg / 572 kg / 692 kg
Maximum platform height 13.20 m

Assembly and usage instructions
10
Fig. 2a.1
Fig. 1a.1 Fig. 1a.2
1
2
1
7
2
1
Fig. 3a.1
Fig. 2a.2
Fig. 2b.1
4
3
1
Fig. 1b.1 Fig. 1b.2
2
Fig. 2b.2
1
2
2.6.a
General assembly regulations
for unpair platform heights (1m,
3m, 5m, …) start with 2m frames
without diagonals in the bottom.
1a.
Assembling swivel castors at first
2m frame.
2a.
Install first advanced guardrail on
top of the 2m frame.
3.a
Install second advanced guardrail.
Go on with point 4.1!
2b.
Put on both sides 2m frames
on top of the 1m frames and
put horizontals and diagonals
in the bottom.
2.5.b
General assembly regulations
for pair platform heights (2m,
4m, 6m, …) start with 1m frames
with diagonals in the bottom.
1b.
Assembling swivel castors at first
1m frame.

Assembly and usage instructions Assembly and usage instructions 11
3b.
Install both advanced guardrails
on top of the 2m frames.
Fig. 3b.2Fig. 3b.1
1
1
2
4.2
Fix platform on rung
Fig. 4.2
4.1
Put the platform on the rung.
Fig 4.1a:
at unpair platform heights (1m,
3m, 5m, …) on 3rd rung
Fig 4.1b:
at pair platform heights (2m, 4m,
6m, …) on 7th rung
Fig. 4.1a Fig. 4.1b
Fig. 5.1 Fig. 5.2
5.
Assembly of stabilisers 4
1
5
6.
Attach ballast weights
(if necessary!)
Fig. 6.1
2
1

Assembly and usage instructions
12
1
2
2
1
8.
Fit toeboards
Fig. 7.3
Fig. 8.1 Fig. 8.2
Fig. 7.2
2.7. Note on dismantling the scaffold tower
To dismantle the scaffold tower, follow the steps for assembly in reverse order. Before
commencing dismantling, ensure that the necessary platforms or scaffold planks are installed
again and laid flat for personnel to stand on. No part of the scaffold tower (braces, platforms etc.)
may be removed before the levels above have been completely dismantled.
11
2
3
2
Fig. 7.4
Fig. 7.1
7.
Put other frames, advanced
guardrails and platforms like
in the way before.
Fig. 7.5
1
2
3
4
5

Assembly and usage instructions Assembly and usage instructions 13
2.8. Basic dimensions
2637
1378
577
1800 - 2500 - 3000
2637
675
2637
1350
3378
3393 - 4093 - 4593
4053
3393 - 4093 - 4593
1800 - 2500 - 3000
1800 - 2500 - 3000

Assembly and usage instructions
14
Plattformhöhe
Platform height
Hauteur plate-forme
max.
12,0 m
max.
8,0 m
Achtung:
Vor Inbetriebnahme
Gebrauchsanleitung und
Einsatzbeschränkungen
beachten
Not
Attention:
Gerüstgruppe
Scaffolding
category
Classe
d'Èchafaudage
3
D
200 kg/m2
EN-1004
gepr¸fte
Sicherheit
e:
read the user guide
and restrictions of use
before erection
avant le montage,
lisez la notice et les
restrictions d’utilisations
42904
4 00 3 8 6 6 4 2 9 0 42
2.9. Identication
Art. No.
Type plate
max. platform height
max. perm. load.
4 0 0 3 8 6 6 4 2 9 0 4 2
42904
EAN code
Art. No.

Assembly and usage instructions Assembly and usage instructions 15
2.10. Parts list incl. ballast (see also 3.2)
Scaffold tower normal 0.75 m x 1.8 m / 2.5 m / 3.0 m
Working height 1) Parts list [1.8 / 2.5 / 3.0] Single wide ladderframe structure 1 m Single wide ladderframe structure 2 m Advanced Guardrail 1.8 m Advanced Guardrail 2.5 m Advanced Guardrail 3.0 m Platform with trapdoor 1.8 m Platform with trapdoor 2.5 m Platform with trapdoor 3.0 m Crosswise board Length toeboard 1.8 m Length toeboard 2.5 m Length toeboard 3.0 m Diagonale brace 1.8 m Diagonale brace 2.5 m Diagonale brace 3.0 m Horizontale brace 1.8 m Horizontale brace 2.5 m Horizontale brace 3.0 m Basic braces 1.8 m Basic braces 2.5 m Basic braces 3.0 m Stabilisers S-PLUS Wheel Ø200 mm Base step
Number of ballast weights per fastening of stabilisers.
Indoors Outdoors
app.
[m]
Order
no.
42905 42904 42837 42838 42839 42931 42910 42933 42913 42943 42914 42944 42937 42908 42938 42935 42907 42936 42886 42887 42888 42850 42917 42940
42912
3.35
52225 - 2 2 - - 1 - - - - - - - - - 2 - - - - - - 4 1 0 0
52226 - 2 - 2 - - 1 - - - - - - - - - 2 - - - - - 4 1 0 0
52227 - 2 - - 2 - - 1 - - - - - - - - - 2 - - - - 4 1 0 0
4.45
52235 2 2 2 - - 1 - - 2 2 - - 2 - - 2 - - - - - 4 4 1 0 0
52236 2 2 - 2 - - 1 - 2 - 2 - - 2 - - 2 - - - - 4 4 1 0 0
52237 2 2 - - 2 - - 1 2 - - 2 - - 2 - - 2 - - - 4 4 1 0 0
5.30
52245 - 4 4 - - 2 - - 2 2 - - - - - 2 - - - - - 4 4 1 0 0
52246 - 4 - 4 - - 2 - 2 - 2 - - - - - 2 - - - - 4 4 1 0 0
52247 - 4 - - 4 - - 2 2 - - 2 - - - - - 2 - - - 4 4 1 0 0
6.45
52255 2 4 4 - - 2 - - 2 2 - - 2 - - 2 - - - - - 4 4 1 0 0
52256 2 4 - 4 - - 2 - 2 - 2 - - 2 - - 2 - - - - 4 4 1 0 0
52257 2 4 - - 4 - - 2 2 - - 2 - - 2 - - 2 - - - 4 4 1 0 0
7.30
52265 - 6 6 - - 3 - - 2 2 - - - - - 2 - - - - - 4 4 1 0 0
52266 - 6 - 6 - - 3 - 2 - 2 - - - - - 2 - - - - 4 4 1 0 1
52267 - 6 - - 6 - - 3 2 - - 2 - - - - - 2 - - - 4 4 1 0 2
8.40
52275 2 6 6 - - 3 - - 2 2 - - 2 - - 2 - - - - - 4 4 1 0 2
52276 2 6 - 6 - - 3 - 2 - 2 - - 2 - - 2 - - - - 4 4 1 0 3
52277 2 6 - - 6 - - 3 2 - - 2 - - 2 - - 2 - - - 4 4 1 0 4
9.25
52285 - 8 8 - - 4 - - 2 2 - - - - - - - - 2 - - 4 4 1 0 X
52286 - 8 - 8 - - 4 - 2 - 2 - - - - - - - - 2 - 4 4 1 0 X
52287 - 8 - - 8 - - 4 2 - - 2 - - - - - - - - 2 4 4 1 0 X
10.40
52295 2 8 8 - - 4 - - 2 2 - - 2 - - - - - 2 - - 4 4 1 0 X
52296 2 8 - 8 - - 4 - 2 - 2 - - 2 - - - - - 2 - 4 4 1 0 X
52297 2 8 - - 8 - - 4 2 - - 2 - - 2 - - - - - 2 4 4 1 0 X
11.20
52305 - 10 10 - - 5 - - 2 2 - - - - - - - - 2 - - 4 4 1 0 X
52306 - 10 - 10 - - 5 - 2 - 2 - - - - - - - - 2 - 4 4 1 0 X
52307 - 10 - - 10 - - 5 2 - - 2 - - - - - - - - 2 4 4 1 0 X
12.35
52315 2 10 10 - - 5 - - 2 2 - - 2 - - - - - 2 - - 4 4 1 0 X
52316 2 10 - 10 - - 5 - 2 - 2 - - 2 - - - - - 2 - 4 4 1 0 X
52317 2 10 - - 10 - - 5 2 - - 2 - - 2 - - - - - 2 4 4 1 0 X
13.20
52325 - 12 12 - - 6 - - 2 2 - - - - - - - - 2 - - 4 4 1 5 X
52326 - 12 - 12 - - 6 - 2 - 2 - - - - - - - - 2 - 4 4 1 5 X
52327 - 12 - - 12 - - 6 2 - - 2 - - - - - - - - 2 4 4 1 5 X
X = not permissible
1) With max. swivelled-out swivel castors 42917 (adjustment range: 0.30 m). Please use anti-twist device 42865 (see Page 34) for
stabilisers to prevent wilful twisting of the stabilisers. Anti-twist devices are prescribed by EN 1004, Point 7.7.1.
Pay attention to the ballasting specifications in the operating and assembly instructions!

Assembly and usage instructions
16
Scaffold tower wide 1.35 m x 1.8 m / 2.5 m / 3.0 m
Working height 1) Parts list [1.8 / 2.5 / 3.0] Single wide ladderframe structure 1 m Single wide ladderframe structure 2 m Advanced Guardrail 1.8m Advanced Guardrail 2.5m Advanced Guardrail 3.0m Platform with trapdoor 1.8 m Platform with trapdoor 2.5 m Platform with trapdoor 3.0 m Platform without trap. 1.8 m Platform without trap. 2.5 m Platform without trap. 3.0 m Crosswise board Length toeboard 1.8 m Length toeboard 2.5 m Length toeboard 3.0 m Diagonale brace 1.8 m Diagonale brace 2.5 m Diagonale brace 3.0 m Horizontale brace 1.8 m Horizontale brace 2.5 m Horizontale brace 3.0 m Basic braces 1.8 m Basic braces 2.5 m Basic braces 3.0 m Stabilisers S-PLUS Wheel Ø 200 mm Base step
Number of ballast weights per fastening of stabilisers.
Indoors Outdoors
app.
[m]
Order
no.
42902 42901 42837 42838 42839 42931 42910 42933 42932 42930 42934 42911 42943 42914 42944 42937 42908 42938 42935 42907 42936 42886 42887 42888 42850 42917 42940
42912
3.35
52425 - 2 2 - - 1 - - 1 - - - - - - - - - 2 - - - - - - 4 1 0 0
52426 - 2 - 2 - - 1 - - 1 - - - - - - - - - 2 - - - - - 4 1 0 0
52427 - 2 - - 2 - - 1 - - 1 - - - - - - - - - 2 - - - - 4 1 0 0
4.45
52435 2 2 2 - - 1 - - 1 - - 2 2 - - 2 - - 2 - - - - - - 4 1 0 0
52436 2 2 - 2 - - 1 - - 1 - 2 - 2 - - 2 - - 2 - - - - - 4 1 0 0
52437 2 2 - - 2 - - 1 - - 1 2 - - 2 - - 2 - - 2 - - - - 4 1 0 0
5.30
52445 - 4 4 - - 2 - - 2 - - 2 2 - - - - - 2 - - - - - 4 4 1 0 0
52446 - 4 - 4 - - 2 - - 2 - 2 - 2 - - - - - 2 - - - - 4 4 1 0 0
52447 - 4 - - 4 - - 2 - - 2 2 - - 2 - - - - - 2 - - - 4 4 1 0 0
6.45
52455 2 4 4 - - 2 - - 2 - - 2 2 - - 2 - - 2 - - - - - 4 4 1 0 0
52456 2 4 - 4 - - 2 - - 2 - 2 - 2 - - 2 - - 2 - - - - 4 4 1 0 0
52457 2 4 - - 4 - - 2 - - 2 2 - - 2 - - 2 - - 2 - - - 4 4 1 0 0
7.30
52465 - 6 6 - - 3 - - 3 - - 2 2 - - - - - 2 - - - - - 4 4 1 0 0
52466 - 6 - 6 - - 3 - - 3 - 2 - 2 - - - - - 2 - - - - 4 4 1 0 0
52467 - 6 - - 6 - - 3 - - 3 2 - - 2 - - - - - 2 - - - 4 4 1 0 0
8.40
52475 2 6 6 - - 3 - - 3 - - 2 2 - - 2 - - - - - 2 - - 4 4 1 0 2
52476 2 6 - 6 - - 3 - - 3 - 2 - 2 - - 2 - - - - - 2 - 4 4 1 0 0
52477 2 6 - - 6 - - 3 - - 3 2 - - 2 - - 2 - - - - - 2 4 4 1 0 0
9.25
52485 - 8 8 - - 4 - - 4 - - 2 2 - - - - - - - - 2 - - 4 4 1 0 3
52486 - 8 - 8 - - 4 - - 4 - 2 - 2 - - - - - - - - 2 - 4 4 1 0 X
52487 - 8 - - 8 - - 4 - - 4 2 - - 2 - - - - - - - - 2 4 4 1 0 X
10.40
52495 2 8 8 - - 4 - - 4 - - 2 2 - - 2 - - - - - 2 - - 4 4 1 0 X
52496 2 8 - 8 - - 4 - - 4 - 2 - 2 - - 2 - - - - - 2 - 4 4 1 0 X
52497 2 8 - - 8 - - 4 - - 4 2 - - 2 - - 2 - - - - - 2 4 4 1 0 X
11.20
52505 - 10 10 - - 5 - - 5 - - 2 2 - - - - - - - - 2 - - 4 4 1 0 X
52506 - 10 - 10 - - 5 - - 5 - 2 - 2 - - - - - - - - 2 - 4 4 1 0 X
52507 - 10 - - 10 - - 5 - - 5 2 - - 2 - - - - - - - - 2 4 4 1 0 X
12.35
52515 2 10 10 - - 5 - - 5 - - 2 2 - - 2 - - - - - 2 - - 4 4 1 0 X
52516 2 10 - 10 - - 5 - - 5 - 2 - 2 - - 2 - - - - - 2 - 4 4 1 0 X
52517 2 10 - - 10 - - 5 - - 5 2 - - 2 - - 2 - - - - - 2 4 4 1 0 X
13.20
52525 - 12 12 - - 6 - - 6 - - 2 2 - - - - - - - - 2 - - 4 4 1 0 X
52526 - 12 - 12 - - 6 - - 6 - 2 - 2 - - - - - - - - 2 - 4 4 1 0 X
52527 - 12 - - 12 - - 6 - - 6 2 - - 2 - - - - - - - - 2 4 4 1 0 X
X = not permissible
1) With max. swivelled-out swivel castors 42917 (adjustment range: 0.30 m). Please use anti-twist device 42865 (see Page 34) for
stabilisers to prevent wilful twisting of the stabilisers. Anti-twist devices are prescribed by EN 1004, Point 7.7.1.
Pay attention to the ballasting specifications in the operating and assembly instructions!

Assembly and usage instructions Assembly and usage instructions 17
2.11. Position of the individual parts
Diagonale brace
Slip-in frame 2 m
Slip-in frame 1m
Platform with trapdoor
Crosswise board
Length toeboard
Horizontale brace
Advanced Guardrail
Stabilisers S-PLUS
Wheel Ø200mm

Assembly and usage instructions
18
1
3
7
1
3
7
Normal, working height 3.35m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52225 52226 52227
1Slip-in frame 2m
42904
222
2
Advanced Guardrail 1.8m
42837
222
Advanced Guardrail 2.5m
42838
-2-
Advanced Guardrail 3.0m
42839
- - 2
3
Platform with trapdoor 1.8m
42931
1 - -
Platform with trapdoor 2.5m
42910
-1-
Platform with trapdoor 3.0m
42933
- - 1
4
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
5Wheel Ø 200mm
42917
444
6Base step
42940
111
Weight [kg]
75 86 95
No ballast weights needed!
1
5
7
11
1
5
7
11
Normal, working height 4.45m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52235 52236 52237
1Slip-in frame 1m
42905
222
2Slip-in frame 2m
42904
222
3
Advanced Guardrail 1.8m
42837
2 - -
Advanced Guardrail 2.5m
42838
-2-
Advanced Guardrail 3.0m
42839
- - 2
4
Platform with trapdoor 1.8m
42931
1 - -
Platform with trapdoor 2.5m
42910
-1-
Platform with trapdoor 3.0m
42933
- - 1
5Crosswise board
42913
222
6
Lengthwise board 1.8m
42943
2 - -
Lengthwise board 2.5m
42914
-2-
Lengthwise board 3.0m
42944
- - 2
7
Diagonal brace 1.8m
42937
2 - -
Diagonal brace 2.5m
42908
-2-
Diagonal brace 3.0m
42938
- - 2
8
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
9Stabiliser S-PLUS
42850
444
10 Wheel Ø 200mm
42917
444
11 Base step
42940
111
Weight [kg]
118 133 144
No ballast weights needed!

Assembly and usage instructions Assembly and usage instructions 19
1
3
7
10
14
1
3
7
10
14
Normal, working height 5.30m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52245 52246 52247
1Slip-in frame 2m
42904
444
2
Advanced Guardrail 1.8m
42837
4 - -
Advanced Guardrail 2.5m
42838
-4-
Advanced Guardrail 3.0m
42839
- - 4
3
Platform with trapdoor 1.8m
42931
2 - -
Platform with trapdoor 2.5m
42910
-2-
Platform with trapdoor 3.0m
42933
- - 2
4Crosswise board
42913
222
5
Lengthwise board 1.8m
42943
2 - -
Lengthwise board 2.5m
42914
-2-
Lengthwise board 3.0m
42944
- - 2
6
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
7Stabiliser S-PLUS
42850
444
8Wheel Ø 200mm
42917
444
9Base step
42940
111
Weight [kg]
145 169 187
No ballast weights needed!
1
1
5
5
7
11
14
18
7
11
14
18
Normal, working height 6.45m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52255 52256 52257
1Slip-in frame 1m
42905
222
2Slip-in frame 2m
42904
444
3
Advanced Guardrail 1.8m
42837
4 - -
Advanced Guardrail 2.5m
42838
-4-
Advanced Guardrail 3.0m
42839
- - 4
4
Platform with trapdoor 1.8m
42931
2 - -
Platform with trapdoor 2.5m
42910
-2-
Platform with trapdoor 3.0m
42933
- - 2
5Crosswise board
42913
222
6
Lengthwise board 1.8m
42943
2 - -
Lengthwise board 2.5m
42914
-2-
Lengthwise board 3.0m
42944
- - 2
7
Diagonal brace 1.8m
42937
2 - -
Diagonal brace 2.5m
42908
-2-
Diagonal brace 3.0m
42938
- - 2
8
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
9Stabiliser S-PLUS
42850
444
10 Wheel Ø 200mm
42917
444
11 Base step
42940
111
Weight [kg]
159 183 202
No ballast weights needed!

Assembly and usage instructions
20
1
3
7
10
14
17
21
1
3
4
10
14
17
21
Normal, working height 7.30m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52265 52266 52267
1Slip-in frame 2m
42904
666
2
Advanced Guardrail 1.8m
42837
6 - -
Advanced Guardrail 2.5m
42838
-6-
Advanced Guardrail 3.0m
42839
- - 6
3
Platform with trapdoor 1.8m
42931
3 - -
Platform with trapdoor 2.5m
42910
-3-
Platform with trapdoor 3.0m
42933
- - 3
4Crosswise board
42913
222
5
Lengthwise board 1.8m
42943
2 - -
Lengthwise board 2.5m
42914
-2-
Lengthwise board 3.0m
42944
- - 2
6
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
7Stabiliser S-PLUS
42850
444
8Wheel Ø 200mm
42917
444
9Base step
42940
111
Weight [kg]
186 219 245
Number of ballast weights per fastening of stabilisers.
Ballast weights indoors
42912
000
Ballast weights outdoors 012
1
5
7
11
14
18
21
25
1
5
7
11
14
18
21
25
Normal, working height 8.40m (0,75m x 1.8m/2.5m/3.0m)
Name ID
52275 52276 52277
1Slip-in frame 1m
42905
222
2Slip-in frame 2m
42904
666
3
Advanced Guardrail 1.8m
42837
6 - -
Advanced Guardrail 2.5m
42838
-6-
Advanced Guardrail 3.0m
42839
- - 6
4
Platform with trapdoor 1.8m
42931
3 - -
Platform with trapdoor 2.5m
42910
-3-
Platform with trapdoor 3.0m
42933
- - 3
5Crosswise board
42913
222
6
Lengthwise board 1.8m
42943
2 - -
Lengthwise board 2.5m
42914
-2-
Lengthwise board 3.0m
42944
- - 2
7
Diagonal brace 1.8m
42937
2 - -
Diagonal brace 2.5m
42908
-2-
Diagonal brace 3.0m
42938
- - 2
8
Horizontale brace 1.8m
42935
2 - -
Horizontale brace 2.5m
42907
-2-
Horizontale brace 3.0m
42936
- - 2
9Stabiliser S-PLUS
42850
444
10 Wheel Ø 200mm
42917
444
11 Base step
42940
111
Weight [kg]
199 233 260
Number of ballast weights per fastening of stabilisers.
Ballast weights indoors
42912
000
Ballast weights outdoors 234