Zico QUIC-STEP HVS-1 Parts list manual

ZICO®
3094PM2
QUIC-STEP®HorIzonTal VEHIClE STEP
ModEl HVS-1
ParTS and InSTrUCTIon ManUal
Step-Out with Condence
The HVS-1 meets NFPA
1901-09 requirements.
Designed specically for use on re and emergency
vehicles. May be retrotted onto existing apparatus.
The open diamond pattern stepping surface is 15" wide
x 9.5" deep. The surface is a non-skid surface to provide
traction and safety.
The HVS-1 only requires 20" wide x 11" deep mounting
surface with an additional 8" clearance behind unit for
the retracted arms allowing it to t almost anywhwere.
MODEL DESCRIPTION WT./@ IN LBS.
HVS-1 Horizontal Vehicle Step 24.1
The HVS-1 is designed to sustain a static
load of 500 lbs. This should be taken into
account in determining strength required of
mounting surface.
The HVS-1 only needs 3" spacing below
mounting surface to clear components.
Rev. 5-3-12

FIGURE 1 - FIELD WIRING DIAGRAM
Page 2
MODE OF OPERATION
* PROVIDE POWER TO HVS-1
EXTEND MODE:
* STEP WILL AUTOMATICALLY EXTEND AS SOON AS THE DOOR IS OPENED.
* STEP WILL REMAIN EXTENDED SO LONG AS DOOR REMAINS OPEN.
RETRACTED MODE:
* STEP WILL AUTOMATICALLY RETRACT AS SOON AS THE DOOR IS CLOSED.
* STEP WILL REMAIN RETRACTED AS LONG AS DOOR REMAINS CLOSED.
ITEM DESIGNATION PART NO. DESCRIPTION QTY.
1 M 3094-200-133 Actuator 1
2 0000-025-101 Fuseholder 1
3 F1 3094-200-157 Fuse, 6 Amp, Self Resetting 1
4 LS1 3097-270-105 Door Switch 1
5 CR1, CR2 3094-200-163 Relay 2
6 3094-200-165 Connector w/Terminals 2
7 3097-270-113 Butt Splice, Blue 4

Page 3
Parts Breakdown
ITEM PART NO. DESCRIPTION QTY.
1 3094-200-101 Linkage, Short A 2
2 3094-200-103 Linkage, Long A 2
3 3094-200-105 Linkage, Long B 2
4 3094-200-107 Actuator Bracket 1
5 3094-200-109 Step Bracket 1
6 3094-200-111 Step Rail Right 1
7 3094-200-113 Grating Cap 2
8 3094-200-115 1" x 1/2" Spacer 4
9 3094-200-117 3/4" x 1" Spacer 3
10 3094-200-119 1/2" x .340" Spacer 2
11 3094-200-121 1/2" x .590" Spacer 1
12 3094-200-123 1/2" x .650" Spacer 2
13 3094-200-125 1/2" x .913" Spacer 1
14 3094-200-127 1/2" x .1.281" Spacer 2
15 3094-200-129 Step Housing 1
16 3094-200-131 Grating 1
17 3094-200-133 Actuator 1
18 9010-293732 3/8-16 x 2" Screw 4
19 9014-113700 3/8" Flat Washer 4
20 9013-113700 3/8-16 Nut 4
21 9010-102512 1/4-20 x 3/4" Hex Screw 4
22 9014-112500 1/4" Washer 15
23 9015-172500 1/4-20 Nut 16
24 9010-102508 1/4-20 x 1/2" Hex Screw 4
25 9014-162500 1/4" Wide Washer 5
26 3097-105-130 3/4" O.D. Washer 19
27 9015-102532 1/4-20 x 2" Hex Screw 3
28 9015-102516 1/4-20 x 1" Hex Screw 4
29 3094-200-135 Step Rail Left 1
30 9010-242008 10-32 x 1/2" Screw 4
31 9014-111900 #10 Washer 4
32 9013-171900 10-32 Nut 4
33 3094-200-137 3/16" Tree Rivits 10
34 3094-200-149 Actuator Bracket Top 1
35 3094-200-171 Step Servo Spring 1
36 3094-200-143 Strut Strength Angle 1
37 3094-200-145 Strut Strength Plate 1
38 9010-102548 1/4-20 x 3" Hex Screw 1
39 3094-200-159 1-1/4" O.D. Washer 2
40 3094-200-161 Actuator Cover 1
41 9025-172006 10-32 x 3/8" Screw 6

Page 4

Page 5

Page 6

Ziamatic Corp.
10 West College Avenue, P.O. Box 337, Yardley, PA 19067-0587 • [phone] • FAX: [phone]
*ZICO is a registered trademark for re, safety and marine products made by Ziamatic Corp.Copyright Ziamatic Corp. 5-12
www.ziamatic.com
TOLL FREE: 800-711-3473
Page 7
Maintenance
A. Semi-Annually or at Scheduled Apparatus Lube Service
1. Visually inspect step linkages for excess dirt build-up, wear of the nylon buttons or debris in
the rail tracks.
2. Lubricate all joints and pivots with CRC Stor & Lube long-term lubricant and rust
preventative #03032. Excess lubrication should be wiped off.
3. Lubricate the rail tracks with door jam grease where the sides of the stop rails run along the
rail tracks.