ZigBoat Schuko ZB207 User manual
eng
· Please check the battery status;
· Please check that the the correct serial number
has been entered.
· Please check if 230 Vac is present in the outlet.
· In case of a weak or a bad signal, change the
location of the ZigBoat™ Smart Plug
“ON”: The electrical device connected to the
smart plug is on (the icon frame in the Zigboat
App is green)
“OFF”: The electrical device connected to the
smart plug is o (the icon frame in the Zigboat
App is red)
You can turn on and o the electrical device
connected to your smart plug by pressing the
smart plug icon on the Overview tab.
Modes
SEARCHING GATEWAY MODE
A red LED is ashing every second
4. After releasing the button, the red LED will
stay on for 2-5 seconds. During that time,
the device must not be switched o or
unplugged.
Resetting
Resetting is needed if you want to connect
your Smart Plug to another Gateway or if you
need to perform a factory reset to remove
abnormal behaviour.
STEPS FOR RESETTING
1. Connect the Smart Plug to the 230 Vac
power outlet.
2. Press and hold down the button on the
device.
3. Hold the button down until the red LED
ashes continuously, then release the button.
Placement
• Place the Smart Plug indoors at a tempera-
ture between 0-50°C.
• Do not remove the product label as it
contains important information.
• Avoid switching maximum loads frequently
on or o, in order to sustain a long life for the
Smart Plug .
• Be careful that no liquid gets into the Smart
Plug as it may damage the adapter.
6. While the Smart Plug is searching for the
network, the LED button is ashing red.
7. When the LED button stops ashing, the
Smart Plug has successfully joined the
ZigBoat™ network.
To check the correct conguration, select the
overview tab of the ZigBoat™ App. (g. 5)
Green dot: The sensor is working properly
Red dot: The sensor is not able to reach the
Gateway.
Product description
The ZigBoat™ Schuko Smart Plug is an
intelligent remote controlled adapter.
The ZigBoat™ Smart Plug allows the user to
instantly switch on and o electrical devices
remotely.
Precautions
Version 1.0
Schuko Smart Plug
OFF MODE
When there is no light in the LED button,
it means that the relay is o (there is
no output). The relay can be switched
on and o by pushing the LED button.
NORMAL MODE
Green LED means that the Smart Plug output
is active (relay is on). The relay can be switched
on and o by pushing the LED button.
code: ZB207
4. Connect the Smart Plug to the 230 Vac
power outlet.
5. The Smart Plug will now start searching for
a ZigBoat™ network to join.
OWNER MANUAL
ON
Smart Plug
Plug #1
Fig. 5
Fig. 1Fig. 2
Adding the sensor to the Gateway
NOTE: Make sure the Gateway is turned on
and congured correctly, for more details see
the Gateway owner manual.
1. Open the ZigBoat™ App, select the Gateway
in the ZB Gateway menu, wait a few seconds,
then select the menu button on the top right
(g. 1) Select “Device list” (g. 2). Add the
sensor by entering the serial number which
is on the sensor’s label (g. 3).
2. The serial number is located between the
2-pin plug.
3. You can change the devices name by
selecting “Name” (g. 4). Then, press the
button “Add Device”.
Fig. 3
Fig. 4
Glomex assumes no responsibility for any
errors, which may appear in this manual.
Furthermore, Glomex reserves the right to alter
the hardware, software, and/or specications
detailed herein at any time without notice, and
Glomex does not make any commitment to
update the information contained herein. All
the trademarks listed herein are owned by their
respective owners.
All rights reserved.
Other certications
• ZigBee® certied
IN ACCORDANCE WITH THE DIRECTIVES
• Radio Equipment Directive 2014/53/EU
• Low Voltage Directive 2006/95/EC
• EMC Directive 2014/30/EU
• RoHS Directive 2011/65/EU
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
which apply to the product and, in particular,
its compliance with the harmonized standards
and specications.
Other information
• The Smart Plug is rated for 10 A continuous
load, and 16 A (~3500 W) short time load.
• It will automatically switch o if the load
exceeds 16 A or the internal temperature
gets too high.
• In case of power failure, the device will
restore itself to the on/o status it had
before the power failure.
Disposal
Dispose the product properly at the end of
life. This is electronic waste which should be
recycled.
Consulta il manuale utente in italiano su:
Consultez le manuel d’utilisation en français
sur:
Siehe das deutsche Benutzerhandbuch auf:
Consulte el manual de usuario en español en:
Fault nding
• In case of power failure, the device will
restore itself to the on/o status it had
before the power failure.
• In case of a bad or weak signal, change the
location of the Smart Plug or your gateway.
• If the search for ZigBoat™ gateway has
timed out, a short press on the LED button
located on the Smart Plug will restart it.
Warranty
Glomex guarantees the Smart Plug (ZB207)
against manufacturing defects for a period of
2 years from date of purchase.
Warranty can be in the form of repair or
replacement of the unit if manufacturing
defects have been found and are conrmed
by Glomex or one of its aliates. In order to
validate warranty, either the original sales
receipt or a copy must be provided at the time
warranty is requested. Before returning any
items for warranty, please contact the Glomex
Customer Service department to receive a
RMA which should be completed and sent with
the unit to the following address:
GLOMEX S.r.l.
Via Faentina 165/G
48124 Ravenna (Italy)
complete with all the accessories supplied at
the time of purchase for shipment. The serial
number must neither be erased nor made
illegible, otherwise the warranty will be voided.
Other ZigBoat Accessories manuals
