Disposal
Dispose the product and battery properly at
the end of life. This is electronicwastewhich
shouldberecycled.
1. To replace the battery, detach the smoke
alarmfromthe mountingbasebytwisting
counter-clockwise.
2. Replacethebatterynotingthepolarity.The
SmokeAlarmSensoruses1xCR123battery.
3. Attachthe alarmin themounting baseby
twisting clockwise until it clicks, and test
thealarm.
EN14604 : 2005/AC:2008
DoP no.: 2102-002
0333
16
DistributedbyGlomexSrl
viaFaentina165/G
48124Ravenna
Italy
Glomex assumes no responsibility for any
errors, which may appear in this manual.
Furthermore,Glomexreservestherighttoalter
the hardware, software, and/or specications
detailedhereinatanytimewithoutnotice,and
Glomex does not make any commitment to
update the information contained herein. All
thetrademarkslistedhereinareownedbytheir
respectiveowners.
All rights reserved.
Glomex guarantees the Smoke Alarm Sensor
(ZB204) against manufacturing defects for
a period of 2 years from date of purchase.
Warranty can be in the form of repair or
replacement of the unit if manufacturing
defects have been found and are conrmed
by Glomex or one of its aliates. In order to
validate warranty, either the original sales
receiptoracopymustbeprovidedatthetime
warranty is requested. Before returning any
itemsforwarranty,pleasecontacttheGlomex
Customer Service department to receive a
RMAwhichshouldbecompletedandsentwith
theunittothefollowingaddress:
GLOMEXS.r.l.
ViaFaentina165/G
48124Ravenna(Italy)
completewithall theaccessories suppliedat
the time of purchase for shipment.The serial
number must neither be erased nor made
illegible,otherwisethewarrantywillbevoided.
Warranty
Other certications
• ZigBee®certied
• RoHS compliant according to the EU
Directive2002/95/EC
• TheZigBoat™SmokeSensorisnotintended
as a device to prevent and detect re and
smoke.
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
whichapplytotheproductand,inparticular,its
compliancewiththeharmonizedspecications
ofstandardEN14604:2005/AC:2008relatingto
ConstructionProductsRegulation305/2011.
Other information
• Notelocalregulationsaboutinformationto
yourinsurancecompanyregardinginstalled
smokealarms.
Battery replacement
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harmelectroniccomponentsinside.
CAUTION: RISK OF EXPLOSION IF BATTERIES
ARE REPLACED BY AN INCORRECT TYPE.
DISPOSE OF THE BATTERIES IN ACCORD-
ANCE WITH INSTRUCTIONS.
Resetting
Resetting is needed it you want to connect
yourSmokeAlarmSensortoanothergateway
or if you need to perform a factory reset to
eliminateabnormalbehavior.
STEPS FOR RESETTING
1. Detachthesensorfromthemountingbase
bytwistingitcounterclockwise.
2. PressandholdtheLEDbuttonuntilitashes
continuously.
3. Releasethebutton.
4. Resettingprocessiscompletewhenthered
LEDstartstoblink.
Modes
SEARCHING GATEWAY MODE
Red LED light in the back of the device is
ashingeverysecond(upto15minutes)
NORMAL MODE
FrontLEDisashingevery45seconds.
ALARM MODE
ThesimultaneousashingofthefrontredLED
andsoundingofintermittentaudiblesignal.
Whensmokeisdetected,thealarmwillsound.
Fault nding & cleaning
• Dust particles in the smoke chamber can
beremovedbyvacuumingthemesh.
• High humidity condensation can be
resolvedbydryingthesmokealarmsensor.
• If the smoke alarm sensor does not work
when the test button is pushed, the
probablecauseisafaultybattery.Replace
thebatteryifitiswornout.
• In case of a bad or weak signal, change
the location of the smoke alarm sensor.
Otherwiseyoucanrelocateyourgateway.
• Ifthesearchforthegatewayhastimedout,
ashortpressontheLEDbuttonwillrestartit.
Consultailmanualeutenteinitalianosu:
Consultez le manuel d’utilisation en français
sur:
SiehedasdeutscheBenutzerhandbuchauf:
Consulteelmanualdeusuarioenespañolen:
Testing
• Always test the working order of the
Smoke Alarm Sensor after installation or
batterychange.
• When pressing the sensor button, the
alarmsoundshouldbeheard.
• Anetworkalarmtestcanbeperformedby
holdingdownthesensorbuttonforatleast
6.5seconds.
Press the “button/top” of the Alarm Sensor
to acknowledge and stop the siren. For 10
minutes after the alarm has been silenced,
there will be no additional alarms to allow
ventilationofthesmokebeingdetected.
LOW BATTERY MODE
Simultaneous audible signals and front LED
ashes every 45 seconds, means that the
batteryshouldbereplaced.
REPLACE DEVICE MODE
IftherearenoaudiblesignalsorthefrontLED
does not ash every 45 seconds, the sensor
should be replaced. The life expectancy of
smoke alarm sensors is generally 10 years,
after which point their sensors begin to lose
sensitivity.
