ZKTeco Atlas 00 Series User manual

Installation Guide
Atlas x00 Series Access Control Panels
Version: 1.0
Date: July, 2019

2
Atlas x00 Series Access Control Panels Installation Guide
What’s in the Box
4 Diodes4 Screws & Anchors 1 Screwdriver

3
Atlas x00 Series Access Control Panels Installation Guide
CONTENTS
What’s in the Box..................................................................... 2
Optional Accessories............................................................ 4
Safety Precautions................................................................... 5
Product PIN Diagram............................................................ 6
LED Indicators............................................................................ 7
Product Dimension................................................................ 8
Installation of Panel & Cabinet...................................... 9
Wiring Legend........................................................................ 10
Power Wiring Diagram .................................................... 11
Wiegand Connection........................................................ 12
OSDP Connection................................................................ 13
REX Connections.................................................................. 14
Lock Connection .................................................................. 15
AUX. I/O Connection ........................................................ 16
Ethernet Connection ........................................................ 17
Typical Installation ............................................................... 18
Troubleshooting ................................................................... 19
Electrical Specifications .................................................. 20
Introduction ............................................................................ 23
Understanding the Atlas Series Network .......... 24
Initial Controller Setup ..................................................... 25
Connect the Controller to the Network ............. 31
Complete the Configuration ...................................... 32
Add a User and Test Access ......................................... 36
Add Secondary Controllers ......................................... 38
Mobile App................................................................................. 39
Special Considerations for Complex Networks ..... 43
Where to Go Next ............................................................... 43
Web Management Application
Programming Guide starts at
page 22

4
Atlas x00 Series Access Control Panels Installation Guide
Optional Accessories
Wiegand Card Reader Prox Card
Alarm
Door Sensor Exit Button
Atlas x00 Series Metal Cabinet
CR10E Card Enroller

5
Atlas x00 Series Access Control Panels Installation Guide
Safety Precautions
The following precautions are to keep user’s safe and prevent any damage.
Please read carefully before installation.
Do not expose to direct sunlight, water, dust and soot.
Do not place any magnetic objects near the product. Mag-
netic objects such as magnets, CRT, T V, monitors or speakers
may damage the device
Do not place the device next to heating equipment.
Prevent water, drinks or chemicals leaking into the device.
This product is not intended for use by children unless they
are supervised.
Do not drop or damage the device.
Do not disassemble, repair or modify the device.
Do not use the device for any purpose other than those
specied.
Remove dust or dirt regularly. While cleaning, wipe dust o
with a smooth cloth or towel instead of water.
Contact your supplier in case of any problem!

6
Atlas x00 Series Access Control Panels Installation Guide
Product PIN Diagram
Ethernet Port
Atlas Power
Figure 1
4 Lock & Door Sensor
Aux Input
RESET
Aux Output
Power Detection
USB Port
Wiegand
Reader 3
WIFI
Wiegand
Reader 4
Wiegand
Reader 1
Wiegand
Reader 2
OSDP
Reader
Status Indicator
The function of reset button (once reset button is pressed, LED will blink fast):
1. Press reset button for about 2-5 seconds, zk firmware will check if there is a USB disk which stores an upgrade package
inserted into controller, if yes, then controller will do firmware upgrade automatically.
2. Press reset button for about 5-10 seconds, zk firmware will temporarily set IP to default 169.254.202.242.
RS485 Comm. (not used)
(POE)

7
Atlas x00 Series Access Control Panels Installation Guide
LED Indicators
COMM1 Flashing Yellow indicates the
system is communicating with upper-level
devices (for example, the PC).(NOT USED)
COMM2 Flashing Yellow indicates the
system is communicating with lower-level
devices (for example, readers).
Flashing (RUN) Green LED indicates
that panel is in normal working state.
LINK Solid Green LED indicates TCP/IP
communication is normal
Flashing (ACT )Yellow LED indicates
data communication is in progress
Flashing (WLAN) Green LED indicates
the system is communicating in wireless
(Wi-Fi) mode.
Flashing (DOOR) Green LED indicates a
door opening signal (a door is opened).
Solid (POWER) Red LED indicates the
panel is powered on.
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 8
Figure 7

8
Atlas x00 Series Access Control Panels Installation Guide
Product Dimension
Atlas x00 Series Metal Cabinet
Figure 10
Figure 9
15in (380mm)
11in
(280mm)
3.15in
(80mm)
The surface of the metal cabinet is high temperature baking paint, which can prevent rust.
Atlas-100 Atlas-200 Atlas-400
4.17 in (140mm)
6.3in (160mm) 7.75in (197mm)
6.73in (171mm)
7.75in (197mm)

9
Atlas x00 Series Access Control Panels Installation Guide
Cable Conduit
(Punch hole for cables)
Atlas Panel
Heat Dissipation Grill
Mounting HolesState Indicators
We recommend drilling the mounting plate screws into solid wood (i.e. stud/beam). If a stud/beam cannot be
found, then use the supplied drywall plastic mollies (anchors).
Step 1
Pass the cable through holes
Step 2
Mount the Metal Cabinet
Step 3
Fasten the Atlas Panel with four screws.
Figure 11
Figure 12
Installation of Panel & Cabinet

10
Atlas x00 Series Access Control Panels Installation Guide
Wiring Legend
Ethernet Cable
P
U
S
H
T
O
T
E
S
T
W
E
E
K
L
Y
P
U
S
H
T
O
T
E
S
T
W
E
E
K
L
Y
FIRE
ALARMDetector
Door Sensor
Floodlight
Exit Button
Normally
Open Lock
Normally
Close Lock
Card Reader
12V DC Power Supply
The auxiliary input may be connected to infrared motion sensors, fire alarms, or smoke detectors. The auxiliary
output may be connected to alarms, cameras or door bells, etc.
Figure 13
OSDP Reader
POE