Zline BLISS Series User manual

SHOWER SYSTEMS
BLISS & EL DORADO
www.zlinekitchen.com
Installation and User Manual

ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams
is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to
providing you an elevated experience in the heart of your home. With an endless selection of
features and finishes, our inspiration is your reality.

WARNING: This product can expose you to chemicals including nickel, which is known to the
State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury
designs and professional features into everyone’s homes. Because we continually strive to improve
our products, we may change specifications and designs without prior notice.

IMPORTANT SAFETY INFORMATION 1
BLISS SHOWER SYSTEM 3
BLISS TUB FILLER 10
BLISS SHOWER FAUCET 14
EL DORADO SHOWER SYSTEM 19
EL DORADO SHOWER FAUCET 26
CARE AND MAINTENANCE 31
TROUBLESHOOTING 32
TABLE OF CONTENTS

1
General Safety
IMPORTANT SAFETY INFORMATION
PRIOR TO INSTALLATION
• Make sure that the cold and hot water lines are turned off.
• Wrap all threaded connections with Teflon tape. Always wrap in a clockwise direction.
• Cover your drain to avoid losing parts.
• Do not disassemble the main system body, as it has been installed and commissioned
correctly and precisely before delivery to the factory.
• To keep the system from jamming, flush the water pipe before installation.
Operating conditions: Working pressure at 0.05-1.0 MPa (including cold and hot water
pressure) with applicable water temperature: 39.2°F - 194°F.
• If soldering the water connections when installing the system, remove the O-rings,
cartridges, and washers before applying any heat.
• Protect your eyes when cutting or soldering.
• Do not over tighten screws/nuts. Finger tighten, then use a wrench/screwdriver to
tighten the fixing screw/nut until snug.

2
Tools Needed
TOOLS NEEDED:
• Wrench
• Screwdriver
• Hammer
• Drill
TIME REQUIRED: +/- 120 minutes
LEGEND:
Hot water
Cold water
Torch
Warning
Plumber’s tape
IMPORTANT SAFETY INFORMATION

1. Flange cover
2. Shower arm
3. Top spray shower
4. Wall valve body
5. Faceplate
6. Sleeve
7. Washer
8. Tooth
9. Screw
10.Handle
11 . Handle
12. Flange cover
13. Angle valve
14. Shower rail
15. Shower handle
16. Hose
BLISS SHOWER SYSTEM
BEFORE INSTALLATION
3
Bliss Shower System

BLISS SHOWER SYSTEM
BEFORE INSTALLATION
4
Bliss Shower System

Solder the copper together.Slide the sleeves onto the pipes and then
insert pipes into the wall valve. Tighten the
ring around the pipes with the wrench. NOTE:
If soldering is involved, you must remove
the internal valve components prior to the
soldering. Please note the original position of
the cartridge.
BLISS SHOWER SYSTEM
INSTALLATION
5
Bliss Shower System

BLISS SHOWER SYSTEM
INSTALLATION
6
Bliss Shower System
Reinstall the valve components into their original
positions.
After soldering, purge the water supply system
for 30 seconds.
Screw the wall valve body into the system with
a screwdriver. Do not overtighten.
Use this diagram to understand the placement
of the wall valve.

Attach the faceplate and remove the plastic.Screw the sleeve and washer into the wall valve
body.
BLISS SHOWER SYSTEM
INSTALLATION
Connect the flange cover to the spout in the
wall. Secure with plumber’s tape to prevent
leaks.
Attach the water control handle.
7
Bliss Shower System

Twist the top spray shower into the shower arm. Connect the angle valve to the flange cover
and screw together. Secure with plumber’s tape
to prevent leaks.
BLISS SHOWER SYSTEM
INSTALLATION
Screw the shower rail into the wall.Use a pencil to mark the mounting holes on the
wall. Use a hammer to put the screws in.
8
Bliss Shower System

BLISS SHOWER SYSTEM
OPERATION
Review the diagram to understand the hot, cold,
and open settings.
Connect the shower handle to the shower rail. Tighten
with a wrench.
9
Bliss Shower System

1. Rough-in
2. Sleeve
3. Faceplate
4. Cap
5. Handle
6. Spout
7. Screw
BLISS TUB FILLER
BEFORE INSTALLATION
10
Bliss Tub Filler

Place the components in the appropriate
location.
Attach the hose using plumbing tape and a
wrench.
Use a screwdriver to screw the faucet onto the
wall.
Mark on the wall where you want the faucet to
be installed.
BLISS TUB FILLER
INSTALLATION
11
Bliss Tub Filler

Take off the protective shield.Tighten the components.
Make sure that the components are aligned
properly.
Screw the sleeve and washer into the wall valve
body.
BLISS TUB FILLER
INSTALLATION
12
Bliss Tub Filler

BLISS TUB FILLER
INSTALLATION
13
Bliss Tub Filler
Review the diagram to understand the hot, cold,
and open settings.
Attach handle to the fixture.
Attach base plate to wall.Attach faucet to base plate.

1. Flange cover
2. Shower arm
3. Top spray shower
4. Wall valve body
5. Faceplate
6. Sleeve
7. Cap
8. Switch handle
BLISS SHOWER FAUCET
BEFORE INSTALLATION
14
Bliss Shower Faucet

BLISS SHOWER FAUCET
INSTALLATION
15
Bliss Shower Faucet
Solder the copper together.Slide the sleeves onto the pipes and then
insert pipes into the wall valve. Tighten the
ring around the pipes with the wrench. NOTE:
If soldering is involved, you must remove
the internal valve components prior to the
soldering. Please note the original position of
the cartridge.

BLISS SHOWER FAUCET
INSTALLATION
16
Bliss Shower Faucet
Reinstall the valve components into their original
positions.
After soldering, purge the water supply system
for 30 seconds.
Place the components in the appropriate
location.
Use this diagram to understand the placement
of the wall valve.