Zodiac Ei2 Expert User manual

Noce d’installaon et d’ulisaon
Français
Instrucons for installaon and use
English
Montage- und Gebrauchsanleitung
Deutsch
Installae en gebruikshandleiding
Nederlands
Manual de instalación y de uso
Espanõl
Manual de instalação e ulização
Português
Manuale di installazione e di uso
Italiano
More documents on:
www.zodiac-poolcare.com
EN
H0470400.B - 2016/10

1
WARNINGS
GENERAL WARNINGS
• Failure to respect the warnings may cause serious damage to the pool equipment or cause serious injury, even death.
• The appliance is intended for use in swimming pools only and must not be used in applicaon other than that for which it is
designed.
• It is important that the equipment is operated by competent and qualied (both physically and mentally) people who have
previously received the instrucons for use. All persons not meeng these criteria must not approach the appliance in order to
avoid exposure to dangerous elements.
• Keep the appliance out of the reach of children.
• The appliance must be installed in accordance with the manufacturer’s instrucons and respecng current local standards. The
installer is responsible for installaon of the equipment and for compliance with naonal installaon regulaons. Under no
circumstances can the manufacturer be held liable in the event of failure to comply with applicable local standards.
• For other than the simple user-maintenance described in this manual, the product must be serviced by a qualied professional.
• Incorrect installaon and/or use may cause serious damage to property or serious injuries (possibly causing death).
• All equipment, even postage and packing paid, travels at the risks and perils of the recipient. The consignee shall make reservaons
in wring on the carrier’s bill of lading if damage is detected, caused during transport (conrmaon to be sent to the carrier
within 48 hours by registered mail with acknowledgement of receipt). In the event of a device containing coolant that has been
turned on its side, menon your reservaons in wring to the carrier.
• If the appliance suers a malfuncon, do not try to repair the appliance yourself, contact a qualied technician.
• Refer to the warranty condions for details of the permied water balance values for operang the appliance.
• Defeang, eliminang or shunng any of the safety that may be a part of the device automacally voids the warranty, as does the
use of unauthorized, third party replacement parts.
• Do not spray inseccide or any other chemical (inammable or non-inammable) in the direcon of the appliance, as this may
damage the body and cause a re.
• Zodiac® Heat pump, ltraon pump and lter appliances are compable with most commonly used pool water treatment systems.
• For heat pump appliances or dehumidiers, do not touch the fan or insert a rod or your ngers through the grang when the
appliance is in operaon. The fan rotates at high speed and may cause injuries or even death.
WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES
• The electrical supply to the appliance must be protected by a dedicated 30 mA dierenal residual current protecon device
(RCD), complying with the standards and regulaons in force in the country where it is installed.
• Before carrying out any operaons, check that:
- The voltage indicated on the rang plate of the appliance corresponds to the mains voltage,
- The power grid is adapted to the power requirements of the appliance, and is grounded.
- The plug (where applicable) is suitable for the socket.
• In the event of abnormal funcon or signs of overheang such as a burning odour from the appliance, turn it of immediately,
unplug it from its power supply and contact a professional.
• Before accessing the enclosure for any reason, ensure that all power to the appliance and also power to any accessories or
external devices which may be connected to the appliance, is disconnected from the mains power supply.
• Do not disconnect and reconnect the appliance to the power supply when in operaon.
• Do not pull on the power cord to disconnect it from the power supply.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order
to avoid a hazard.
• Do not operate or service the product with wet hands.
• Ensure that all terminals for mains power are free in good condion and free of corrosion and/or dirt/debris.
• For any component or sub-assembly containing a baery: do not recharge or dismantle the baery, or throw it into a re. Do not
expose it to high temperatures or direct sunlight.
• In stormy weather, unplug the appliance to prevent it from suering lightning damage.
• Do not immerse the appliance in water (with the excepon of cleaners) or mud.
Recycling
This symbol means that your appliance must not be thrown into a normal bin. It will be selecvely collected for the
purpose of reuse, recycling or transformaon. Any substances it may contain which are potenally dangerous to the
environment shall be eliminated or neutralised.
Request informaon on recycling procedures from your retailer.

2
Contents
1. Informaon before installaon .............................................................................. 3
1.1 Contents............................................................................................................................................. 3
1.2 Technical specicaons...................................................................................................................... 3
2. Installaon............................................................................................................. 4
2.1 Preparing the pool: water balance ....................................................................................................4
2.2 Installing the control box ...................................................................................................................4
2.3 Installing the cell................................................................................................................................ 4
2.4 Installing the ow controller (Ei² Expert only) ................................................................................... 5
2.5 Electric connecons........................................................................................................................... 6
3. Use ........................................................................................................................ 7
3.1 Descripon of the Ei² - GenSalt OE user interface ............................................................................ 7
3.2 Descripon of the Ei² Expert user interface.......................................................................................7
4. Maintenance........................................................................................................ 11
4.1 Washing the pool lter (backwash) .................................................................................................11
4.2 Cleaning the electrode..................................................................................................................... 11
4.3 Winterizing....................................................................................................................................... 11
5. Troubleshoong................................................................................................... 12
6. Product conformity.............................................................................................. 12
• Before you do anything with the device, it is vital that you read this installaon and user manual, as well
as the "warnings and warranty" booklet delivered with the device. Failure to do so may result in material
damage or serious or fatal injury and will invalidate the warranty.
• Save these instrucons for future reference for service and maintenance.
• It is prohibited to distribute or modify this document in any way without authorisaon from Zodiac®.
• Zodiac® is constantly developing its products to improve their quality; therefore, the informaon contained
in this document may be modied without noce.
EN

3
1. Informaon before installaon
1.1 Contents
Ei² - GenSalt OE
Control box Cell Installaon kit
Ei² Expert
Control box Cell Installaon kit Fixture collar kit
1.2 Technical specicaons
Power supply voltage 230 Vac-50 Hz
Electric power Max. 140 W
Protecon index IPX5
Box size (l x h x d) 28.5 x 40.5 x 12.5 cm
Cell size (l x h x d) 16.5 x 22.5 x 12.5 cm
Weight (box + cell) 6.0 kg (+/- 500 g depending on model)
Minimum Maximum
Flow through the cell 5 m³/h 18 m³/h - ND 50 mm
25 m³/h - ND 63 mm
Pressure in the cell /2.75 bar
Operang water temperature 5 °C 40 °C

4
2. Installaon
2.1 Preparing the pool: water balance
These appliances are designed to disinfect pool water using its salt water chlorinaon funcon.
It is essenal that the pool water balance and salinity are controlled and adjusted before the appliance is installed. Making
sure that those parameters are correct from the very start will reduce the likelihood of encountering problems on the rst
days of operaon or during the season the pool is in use.
Even though it is an autonomous system, it is essenal to regularly analyse the water to check the water balance
parameters and adjust them if necessary.
Unit Recommended
values To increase To decrease Test frequency (during season)
pH /7.2 – 7.4 Add pH+ or use
automac regulaon
Add pH- or use
automac regulaon Weekly
Free
chlorine
mg/L or
ppm 0.5 – 2
Increase the chlorine
producon or use Boost
mode (Ei² Expert only)
Reduce chlorine
producon Weekly
TAC
(alkalinity or
buering power)
°f
(ppm)
8 – 15
(80 – 150)
Add alkaline corrector
(Alca+ or TAC+) Add hydrochloric acid Monthly
HL
(level of calcium
carbonate)
°f
(ppm)
10 – 30
(100 – 300) Add calcium chloride
Add a calcium carbonate
sequestering agent
(Calci-) or carry out
carbonate removal
Monthly
Cyanuric
acid
(stabiliser)
mg/L or
ppm < 30 Only add cyanuric acid if necessary (Chlor Stab)
Parally empty the pool
and rell it Quarterly
Salinity g/L or
kg/m³ 4Add salt
Leave as such or
parally empty the pool
and rell it
Quarterly
Metals
(Cu, Fe, Mn…)
mg/L or
ppm ± 0 /Add metal binder (Metal Free) Quarterly
2.2 Installing the control box
• The control box must be installed in a dry venlated equipment room protected against frost, with no pool maintenance
products stored nearby.
• The control box must be installed a minimum of 2.0m from the surrounding edge of the pool. Any addional local
installaon codes in the installaon country must also be adhered to.
• It must not be installed more than 1.5 metres from the cell (maximum cable length).
• If the box is xed to a post, a waterght panel must be xed behind the control box (350x400 mm minimum).
• Fix the support solidly to the wall or the waterght panel, and place the control box on it using the screws provided.
2.3 Installing the cell
Ei² - GenSalt OE Ei² Expert
EN

5
• The cell must be installed on the piping aer the ltering, aer any measurement sensors, and aer eventual heang systems.
• The cell must be installed on a horizontal pipe to ensure an essenally horizontal ow of water through it, with no more than a 30
deg angle/slope. The pipe must have a free horizontal length of at least 30cm on which the cell will be installed. The cell must also
be installed as far away as possible from any bends or elbows in the plumbing (1).
• Ensure that the direcon of ow of water through the cell is in accordance with the arrows marked on the cell (see arrows (2)).
• Dismantle the cell.
• Posion the lower collar of the cell (3) upside down at the posion where the pipe will be installed.
• Use a drill bit or centre-punch to mark the posions of the holes to be drilled on the pipe (4), remove the lower collar and drill the
holes using the hole saw supplied.
• Check that the edges are perfectly smooth and deburred (use abrasive paper, for example).
• Clip together the lower and upper parts of the cell collar on the pipe at the holes, respecng the water ow direcon (use the "EU"
Ø50 reducer for a Ø50 mm pipe).
• Posion the top transparent part of the cell (presence of a foolproof locang notch), posion the locking ring on the
thread of the upper collar, then ghten rmly by hand (do not use a tool).
• Connect the cell power supply cable in compliance with the wire colour codes (red, black and blue connectors) and then
t the protecve cap.
• Pour les modèles Ei² 12, GenSalt OE 10 ou Ei² Expert 10, le deuxième connecteur rouge ne sera pas branché ; le laisser
tel quel avant de mere le cache de protecon.
• The cell must always be the last element placed on the pool return pipe (see diagram).
• It is always recommended to install the cell on a by-pass. This assembly is MANDATORY if the ow is in
excess of 18 m³/hour to avoid load loss.
• If you installed the cell on a by-pass, it is recommended to t a check valve downstream from the cell
instead of a manual valve, to avoid the risk of an improper seng which could result in the incorrect ow
water back into the cell.
• Failure to locate and orient the cell in strict accordance with these instrucons can result in a hazardous
buildup of pressurized gas which can result in serious property damage and serious injury, including loss of
life.
An "AUS" reducer and a black seal are supplied in the installaon kit. They are intended for 1 1/2" (= 38 mm)
pipes. However, the black seal can be used instead of the original seal if the pipe is not standardised (diameter
smaller than ND 50 or ND 63).
2.4 Installing the ow controller (Ei² Expert only)
The ow controller and its xture collar (Ø50 mm) must imperavely be installed on the piping close to the cell and
upstream from it. Use the threaded adapter and Teon tape supplied to install the ow controller on its xture collar.
• Cell installed in by-pass: the ow controller must be installed on the cell by-pass between the upstream isolaon valve
and the cell itself.
• Cell installed in line: the ow controller must be installed just in front of the cell and aer a possible valve.
• Fixer le contrôleur de débit en ulisant uniquement l’écrou de serrage.
Écrou de
serrage
• Failure to comply with these instrucons could lead to the destrucon of the cell! The manufacturer cannot
be held liable in this case.
• The ow detector has a direcon for installaon (arrow indicated on it showing the ow direcon
for the water). Make sure that is is correctly placed on its xture collar so that it stops the salt water
chlorinator producon when ltering is stopped ("No ow" displayed showing the absence of ow, see "5.
Troubleshoong").

6
2.5 Electric connecons
2.5.1 Connecng the control box
The salt water chlorinator can be connected in compliance with the applicable standards in the country of installaon.
Ei² - GenSalt OE :
• Mandatory connecon: directly interlocked with the pool ltraon pump (the appliance is only supplied with power
when the pool ltraon pump is operang).
Ei² Expert:
• Preferred connecon: the appliance is permanently connected (hard-wired) to the power supply (power supply
protected by a 30 mA ground fault circuit breaker).
• Possible connecon: directly coupled to the pool ltering (the appliance is only supplied with power when ltering is
operang).
==> When all connecons (electrical and hydraulic) have been made, reconnect (turn on) the mains power supply to
power on the appliance.
• Failure to comply with these instrucons could lead to the destrucon of the cell! The manufacturer cannot
be held liable in this case.
• Whichever connecon is used, it is mandatory to programme the Ei² Expert operang mes (called "Timers")
(see "3.2.5 "Summer" and "Winter" modes and seng the "Timers"").
2.5.2 Connecon to an electric pool cover (Ei² Expert only)
If the pool is ed with an electric roll-on electric pool cover, it can be connected to the Ei² Expert chlorinator using a
dry contact so that the laer automacally adapts its chlorine producon when the electric pool cover is closed (see "").
• Make sure the appliance is powered o and disconnected (e.g., by turning o the circuit breaker or disconnect switch)
from the mains source of power.
• Remove the 12 screws securing the cover screws and remove it (take care not to tear out the ribbon cables).
• Unscrew the dedicated cable gland ghtening ring (at the boom of the control box) and remove the plug to feed
through the cable from the electric pool cover. Tighten the cable gland ghtening ring.
• Connect the cable from the electric pool cover on the "POOL+" and "POOL-" connectors on the electronic board.
• Close the box respecng the ghtening order shown on the following diagram (9 long screws for the perimeter of the
box and 3 short screws for the boom of the box). The box IPX5 protecon index cannot be guaranteed if this procedure
is not followed.
Ei² Expert connecons Torque = 1.2 N.m (= 12.2 kg.cm)
Ei²
GenSalt OE
Ei²
Expert
Ei²
GenSalt OE
Ei²
Expert
AMains power supply 220-240 Vac / 50 Hz X X EConnecon of ow detector X
BCell power supply X X FRibbon cables at the user interface X (1) X (2)
CMemory baery type CR2032 X X GTransformer connecons X X
DCover connecon (contact closed = cover closed) XHFuse 2.5 A me-delayed X X
EN

7
• The Ei² Expert chlorinator is compable with several dierent types of electric pool cover. However, certain
systems may not be compable. In this case, acvate "Low" mode manually from the chlorinator control panel
(see "").
• Refer to the electric pool cover manufacturer's installaon manual.
• The dry contact operang principle is as follows: contact closed = electric pool cover closed.
3. Use
3.1 Descripon of the Ei² - GenSalt OE user interface
Increase or reducon the chlorine producon:
20 %
40 % 60 % 80 %
100 %
- Acvate / deacvate the chlorine producon by a short press.
- Switch o the device with a long press (5 seconds).
- Switch on the device with a short press.
FLOW Red indicator showing the absence of ow and/or presence of air in the cell.
SALT Orange indicator showing a water conducvity problem (not enough salt,
water too cold, etc.).
3.2 Descripon of the Ei² Expert user interface
- Exit the user menu or the internal sengs menu.
- Deacvate Boost mode or Low mode.
- From the home screen: increase or decrease in chlorine producon.
- In the user menu: value changes when a choice is proposed (ashing
characters).
- Simultaneous press for 5 seconds: access the internal sengs menu.
- Access to user menu and navigaon in the sengs (with successive
presses)
- Acvate/deacvate the chlorine producon by a short press.
- Switch o the device with a long press
- Switch on the device with a short press
and - Acvate Boost mode
and - Acvate "Low" mode manually
If the language displayed on the screen when the Ei² Expert is rst switched on is not appropriate, see "3.2.6
"Internal sengs" menu".

8
3.2.1 Chlorine producon acvated
When chlorine producon starts, the "Start..." message is displayed on screen for about 6 seconds. "CHLORINATION" is
then displayed, indicang that the device is producing chlorine.
3.2.2 "Boost" mode: chlorine producon increased to 100 % for 24 h
In certain cases the pool may need higher than normal chlorinaon (stormy weather, high number of bathers, etc.).
"Boost" mode is used to increase chlorine level quickly.
• Press buons and simultaneously: "BOOST" is displayed on the screen and 100 % chlorine producon
starts.
• To stop "Boost" mode, press .
When "Boost" mode is acvated, the rated chlorine producon sengs are temporarily overridden and the Ei²
Expert chlorinator will operate for a total of 24 hours at 100 % chlorine producon. The number of days will
therefore depend on the Ei² Expert operang mes (see "3.2.5 "Summer" and "Winter" modes and seng the
"Timers"").
3.2.3 "Low" mode: chlorine producon reduced to 10 % if the pool is covered
If the pool has a covering system (shelter, electric pool cover, etc.), "Low" mode is designed to adapt the chlorine
producon to situaons where the pool is covered (lower needs). Its eect is to limit chlorine producon to 10%.
This mode is also called " electric pool cover" mode.
Manual acvaon (shelter, cover, etc.) :
• Press buons and simultaneously: "LOW" is displayed on the screen and chlorine producon is reduced
to 10 %.
• To stop "Low" mode, press .
Automac acvaon (compable electric pool cover):
• Make sure that the electric pool cover is compable and connected to the Ei² Expert chlorinator (see "").
• «Low» mode will automacally be acvated when the electric pool cover is closed.
• "Low" mode will stop as soon as the electric pool cover is completely open.
3.2.4 Seng the me
The Ei² Expert chlorinator is ed with an internal memory. When the device is rst switched on it is important
to leave it powered on connuously for at least 24 hours in order to inially charge the accumulator (permanent
separate power supply or ltering on permanently). Once charged the accumulator has several weeks of
autonomy in the event of a power failure.
The me is displayed in a 24 hour format.
• Switch on the device and wait unl screen start-up sequence is nished.
• Press the buon to access the user menu, the minutes start to ash.
• Use the and buons to set the minutes, then press to store.
• Use the and buons to set the hours, then press to store.
• Press the buon to return to the home screen.
EN

9
3.2.5 "Summer" and "Winter" modes and seng the "Timers"
"Timer" programming is used to dene the device operang mes within the ltering system operaon mes.
The daily operang mes must be sucient to correctly treat the water. Ei² Expert proposes default sengs of
Timers 1 and 2. They can be customised (see "3.2.5.b Programming the mers according to the modes").
A reminder of the calculaon rule: the ideal daily ltering me is obtained by dividing the required pool water
temperature (measured in °C) by 2.
Example: for water at 28 °C, me = 28/2 = 14 hours per day
The Ei² Expert chlorinator can store 2 seasonal operang modes called by default "Sum" and "Win". The following
sengs can be customised for each mode:
- the device operang mes, the "mers": T1 (Timer 1) and T2 (Timer 2)
- the required chlorine producon rate: 10 %, 20 %, 30 %,... up to 100 %.
STANDBY = Device operang status
T = "Timer" mode (always acve)
SUM = "Summer" operang mode
80 % = chlorine producon rate
14:25 = me in 24 h format
3.2.5.a Mode selecon: "SUMMER" or "WINTER"
• Press 4 mes to set the clock. "SUM" starts to ash.
• Use the and buons to choose "SUM" or "WIN" mode, then press the buon to return the home
screen.
3.2.5.b Programming the mers according to the modes
The mes of Timers 1 and 2 cannot overlap. In addion, the me range of Timer 1 necessarily precedes that of
Timer 2.
TE1 / TE2 = Timer in "summer" mode No. 1 / Timer in "summer" mode No. 2
08:00-12:00 = Operang me range of Timer No. 1
14:00-18:00 = Operang me range of Timer No. 2
• Press 4 mes to set the clock. "SUM" starts to ash.
• Select the mode to be customised "SUM" or "WIN" using the and buons, then press to store and
move to the mer seng screen.
• Use the and buons to set the Timer 1 stop minutes, then press to store.
• Use the and buons to set the Timer 1 stop hours, then press to store.
• Use the and buons to set the Timer 1 start minutes, then press to store.
• Use the and buons to set the Timer 1 start hours, then press to store.
• Repeat the steps for Timer 2.
• Press the buon to store the mers and move to seng the chlorine producon rate.
• Use the and buons to choose the required chlorine producon rate (from 10 % to 100 %).

10
3.2.6 "Internal sengs" menu
Ei² Expert has an "Internal sengs" menu to change and/or view the following operang parameters:
• Language
• Polarity inversion cycles
• Operang hours counter
To access this menu, press the and buons simultaneously for 5 seconds.
EMEA: Device sale and use region (not modiable)
FR French: Language used (modiable, by default = French)
Cyc=5h: Polarity inversion cycle (modiable, by default = 5 h)
00000: Operang hours counter (not modiable)
3.2.6.a Seng the language
By default the Ei² Expert chlorinator is set to display in French. 13 languages are available: French, English, Spanish,
Italian, Swedish, German, Portuguese, Dutch, Afrikaans, Czech, Hungarian, Slovakian and Turkish.
• From the home screen, press the and buons for 5 seconds. The current language starts to ash.
• Use the and buons to select the required language.
• Press the buon to return to the home screen.
3.2.6.b Polarity inversion
The choice of polarity inversion cycles may aect the cell lifeme (+/- 15 %). Ask your professional reseller for
advice in case of doubt.
The electrolyc cell is equipped with a smart polarity inversion system designed to prevent the electrode plates
from scaling. However cleaning may be required in regions where the water is very hard. (default seng = 5
hours).
Ei² Expert oers a choice of 3 inversion cycles:
• 3 hours: for water of high carbonate content (TH > 40 °f or 400 ppm)
• 5 hours: for normal water (20 °f < TH < 40 °f or 200 ppm < TH < 400 ppm)
• 7 hours: for water of low carbonate content (TH < 20 °f or 200 ppm).
• From the home screen, press the and buons for 5 seconds.
• Press the buon. The polarity inversion cycle hours start to ash.
• Use the and buons to select the required cycle.
• Press the buon to return to the home screen.
EN

11
3.2.6.c Operang hours counter
Ei² Expert can count its total operang hours (= chlorine producon me, aché en jours). This informaon
may be useful to determine the electrode age. The value is provided for informaon only and may be modied.
• From the home screen, press the and buons for 5 seconds.
• The number of operang hours is displayed at the boom right of the screen.
• Press the buon to return to the home screen.
4. Maintenance
4.1 Washing the pool lter (backwash)
L’appareil doit impéravement être éteint lors des procédures de lavage de ltre. When the device is on
(ltraon on), press the buon for 5 seconds to switch it o.
Aer cleaning the lter, switch the device on again by pressing the buon (short press). It will resume
normal operaon (producon slaved to ltraon for Ei² and GenSalt OE.
Pour Ei² Expert la producon fonconnera selon le réglage des mers.
The manufacturer cannot be held liable in case of incorrect handling.
4.2 Cleaning the electrode
The electrolyser is equipped with a smart polarity inversion system designed to prevent the electrode plates from
scaling. However cleaning may be required in regions where the water is very hard. (default seng = 5 hours).
• Turn o the chlorinator and the ltering, close the isolaon valves, remove the protecon cover and disconnect the cell
power cable.
• Unscrew the ghtening ring and remove the cell. The ring is notched thus allowing a lever to be used in the event of it
jamming. Place the cell backwards and ll it with a cleaning soluon so that the electrode plates are immersed.
• Leave the cleaning soluon to dissolve the scale deposit for about 15 minutes. Dispose of the cleaning soluon at an
approved waste recycling site, never pour into the rainwater drainage system or into the sewers.
• Rinse the electrode using clean water and put it back on the cell xture collar (there is an alignment foolproofer).
• Ret the ghtening ring, reconnect the cell cable and ret the protecve cover. Open the isolaon valves and restart
the ltering and chlorinator.
• If you do not use a commercially available cleaning soluon, you can manufacture it yourself by carefully
mixing 1 volume of hydrochloric acid with 9 volumes of water (Warning: always pour the acid into the water
and not the opposite and wear suitable protecve equipment!).
• Make sure that the seng of the polarity inversion cycles is adapted to the pool water hardness. See "3.2.6.b
Polarity inversion" to change them.
4.3 Winterizing
The chlorinator has a protecve system to limit chlorine producon under poor operang condions such as cold
water (winter) or a lack of salt.
• Acve winterizing = ltering operaonal in winter: below 10 °C it is preferable to switch o the chlorinator. Above this
temperature you can leave it running.
• Passive winterizing = lower water level and drained piping: leave the electrode dry in its cell with its isolaon valves
open.

12
5. Troubleshoong
Ei²
GenSalt OE Ei²Expert Possible causes Soluons
«FLASH»
INVERSION The self-cleaning cycle is automac;
this message is not an error code
but an informaon message.
• Wait for about 10 minutes and chlorine
producon will resume automacally at
the previously set level.
/ HIGH SALT • Salt overload (> 10 g/L). • Drain the pool parally to reduce the salt
concentraon.
"Salt" indicator
on
CHECK SALT • Lack of salt (< 3g/L) due to water
loss or diluon (lter backwash,
water renewal, rain, leaks, etc.).
• Pool water temperature too low
(< 18 °C, variable).
• Cell scaled up or worn.
• Add salt to the pool to keep the level at
4 g/l. If you do not know the salt level or
how to test it, consult your reseller.
• Basic producon limitaon signal when
the water is too cold. Reduce chlorine
producon or add salt to compensate.
• Clean or replace the cell.
"Flow" indicator
on
NO FLOW • Stop or failure of the ltering
pump.
• Presence of air or gas in the cell
(incorrect lling with water).
• By-pass valves closed.
• Flow controller and/or cell
disconnected or defecve.
• Check the pump and its programming
clock, the lter, the skimmer(s), and the by-
pass valves. Clean them if necessary.
• Check the cable connecons (cell and ow
controller).
• Check that the ow controller is working
correctly (replace it if necessary).
/
PUMP
CONTROLLER
• This message is displayed
alternately with "NO FLOW" if
the situaon connues.
• Perform the same checks as above.
/
OUTPUT
FAULT
• Short-circuit in the cell or cable
disconnected/badly connected.
• Worn electrode.
• Important manque de sel, ou pas
de sel.
• Sel non encore susamment
dilué.
• Check the cell connecons.
• Replace the cell.
• Have the control box (electronic board
and transformer) checked by a qualied
technician if necessary.
• Ajouter du sel dans la piscine pour
maintenir un niveau à 4 g/L.
/
OVERHEAT-
ING
• Device internal temperature
over 70 °C.
• Device internal temperature
over 80 °C.
• The device reduces its producon to 50 %.
• Producon stops.
• Producon restarts automacally when the
temperature drops.
/
Loss of
me
seng
• The accumulator is worn or
defecve.
• Check the condion of the accumulator.
• Replace it if necessary (3 V accumulator,
type "CR2032"), see "" to open and close
the box.
==> If the problem continues contact your reseller
6. Product conformity
This appliance has been designed and manufactured to comply with the applicable requirements of the following stand-
ards :
EN6000-6-1: 2006
EN6000-6-3: 2007
IEC 60335-1
Relative to which it is compliant. The product has been tested under the intended normal conditions of use.
EN

Pour plus de renseignements, merci de contacter votre revendeur.
For further informaon, please contact your retailer.
ZODIAC® is a registered trademark of Zodiac Internaonal, S.A.S.U., used under license.
Votre revendeur / your retailer
www.zodiac-poolcare.com
Zodiac Pool Care Europe - BP 90023 - 49180 St Barthélémy d’Anjou cedex - S.A.S.U. au capital de 1 267 140 € / SIREN 395 068 679 / RCS PARIS