Zoom F2-BT User manual

F2/F2-BT
You must read the Usage and Safety Precautions before use.
Operation Manual
© 2021 ZOOM CORPORATION
Copying or reprinting this manual in part or in whole without permission is prohibited.
Product names, registered trademarks and company names in this document are the property of their respective companies.
All trademarks and registered trademarks in this document are for identification purposes only and are not intended to
infringe on the copyrights of their respective owners.
You might need this manual in the future. Always keep it in a place where you can access it easily.
The contents of this manual and the specifications of the product could be changed without notice.
The Operation Manual can be downloaded from the ZOOM website (www.zoom.jp/docs/f2_f2-bt).
This page has les in PDF and ePub formats.
The PDF le format is suitable for printing on paper and reading on a computer.
The ePub format can be read with electronic document readers and is designed for reading on smart-
phones and tablets.
Field Recorder

2
Contents
F2/F2-BT features…………………………………………………………………………………………………………………………………… 3
Use examples ………………………………………………………………………………………………………………………………………… 3
Functions of parts ………………………………………………………………………………………………………………………………… 4
Preparing for use …………………………………………………………………………………………………………………………………… 5
Turning the power on……………………………………………………………………………………………………………………………… 6
Connecting the lavalier mic…………………………………………………………………………………………………………………… 6
Recording ………………………………………………………………………………………………………………………………………………… 7
Playing recordings ………………………………………………………………………………………………………………………………… 7
Transferring files to computers …………………………………………………………………………………………………………… 8
Using a computer to change settings ………………………………………………………………………………………………… 9
Connecting to a smartphone/tablet and using F2 Control for remote control (F2-BT only) ……… 9
List of F2 Editor/F2 Control functions …………………………………………………………………………………………………10
Troubleshooting………………………………………………………………………………………………………………………………………11

3
F2/F2-BT features
With a dual A/D converter circuit and support for 32-bit float WAV files, recording with the
highest audio quality is possible.
■ Dual A/D converter circuit
The input circuit has two A/D converters with different input gains. Recording with high
audio quality is possible without adjusting the gain whether the input sound is loud or quiet.
■ 32-bit 󽗊oat WAV 󽗉les
Recording with 32-bit float WAV file formats allows audio quality to be retained when
editing.
• Wide dynamic range
• Recording level always
optimal
• High resolution even
for quiet sounds • Waveforms can be restored to unclipped states
Use examples
Since input gain adjustment is unnecessary, recording can be started by pressing a single
button after putting the mic on.

4
Functions of parts
■ Front
① ② ④
⑤
⑥
⑨
⑦
⑧
③①BATT LED
The color of the light changes
according to the remaining battery
charge.
②INPUT LED
This lights according to the input
level through the INPUT jack.
③ OUTPUT VOLUME −/+ buttons
Use these to adjust the output
volume. Raising the volume too
much could cause the monitored
sound to become distorted, but the
recorded data will not be distorted.
④ REC/PLAY LED
This lights during recording and
playback.
⑤ Power switch
Use this to turn the power ON/OFF
and to disable button operation.
⑥ REC button
Use this to start/stop recording.
⑦ Play button
Use to play recorded files.
⑧ Stop button
Press to stop playback of recorded
files.
⑨ Battery compartment cover
Remove when installing or removing
batteries.
■ Back
⑪
⑩
⑩ Belt clip
⑪ microSD card slot
Insert a microSD card here.

5
■ Top
① ② ③
① DC 5V (USB Type-C) connector
• A dedicated AC adapter (ZOOM AD-17) can
also be connected here to use AC power.
• This can also be connected to a computer
for use. Files can be moved, and F2/F2-BT
settings can be made using the F2 Editor
app.
② OUTPUT jack
Connect headphones, for example, here.
③ INPUT jack
Connect a lavalier mic here.
Preparing for use
In order to use an F2/F2-BT, an application must be installed on a computer and initial
settings for it must be made. See page 9 for details about installing the application.
■ Turn the power on
After turning the power off, open the battery compartment cover
and install batteries. When the power is on, the remaining battery
charge can be checked with the BATT LED.
BATT LED Remaining
battery charge
Lit green Full
Empty
Lit orange
Blinking orange
Blinking red
HINT
An AD-17 AC adapter can also be used.
NOTE
• Use only one type of batteries (alkaline, NiMH or lithium) at a time.
• If the BATT LED does not light after the power is turned on, set the power to OFF and install
new batteries.
• After installing the batteries, set the battery type correctly. Use F2 Editor or F2 Control (F2-BT
only) to set this.
AAA batteries

6
■ Insert a microSD card
After turning the power off, open the microSD card slot cover and
insert a card.
To remove a microSD card, push it further into the slot and then
pull it out.
NOTE
• Always make certain that the power is off when inserting or removing a microSD card.
Inserting or removing a card while the power is on could result in data loss.
• When inserting a microSD card, be sure to insert the correct end with the top side up as
shown.
• Recording and playback are not possible when a microSD card is not loaded.
• Use F2 Editor to format microSD cards.
Turning the power on
1. Set to ON.
2. To turn the power off, set to OFF.
HINT
Setting to HOLD will disable button operations.
Connecting the lavalier mic
1. Attach the windscreen and the clip to the lavalier mic.
2. Connect the lavalier mic to the INPUT jack, and tighten the screw lock.
Windscreen
Mic clip
Pass the cable through the
slot in the lavalier mic clip
before use.
Lavalier mic
INPUT jack
microSD card

7
HINT
• Mics without screw locks can also be connected.
• The INPUT LED lights green according to the input level. If the input level is too high, it will
blink red.
NOTE
• The INPUT jack always supplies plug-in power (2.5 V).
• Check the power specifications before using a mic made by a different company.
• Do not connect a device that does not support plug-in power.
Recording
1. Press .
2. Press again to stop recording.
NOTE
During recording, the REC/PLAY LED lights red.
Playing recordings
1. Connect headphones, for example, to the
OUTPUT jack.
2. Press .
3. Press to stop playback.
HINT
• Use to adjust the output volume.
• During playback, the REC/PLAY LED lights green.
REC button
Headphones
OUTPUT jack
Play buttonStop button

8
Transferring les to computers
1. Turn the F2/F2-BT power on.
2. Use a USB cable to connect the F2/F2-BT and the computer.
USB Type-C port
3. Use the computer to transfer the necessary les.
4. When you want to disconnect, use the computer to end the USB connection with the
F2/F2-BT.
■ F2/F2-BT folder and 󽗉le structure
When recording with an F2/F2-BT, folders and files are created on microSD cards in the
following manner.
Root
200101_001.WAV
200101_010.WAV
200101_024.WAV
F2SETTING.ZST (F2/F2-BT settings file)
F2 Settings

9
Using a computer to change settings
1. Install F2 Editor on the computer.
This can be downloaded from the ZOOM website (zoomcorp.com).
2. Turn the F2/F2-BT power on.
3. Use a USB cable to connect the F2/F2-BT and the computer.
USB Type-C port
4. Launch F2 Editor, and change the F2/F2-BT settings.
NOTE
Connection with a computer is not possible during recording or playback.
Connecting to a smartphone/tablet and using F2 Control
for remote control (F2-BT only)
1. Install the F2 Control app from the App Store or Google Play on the smartphone/
tablet.
2. Turn the F2-BT power on.
3. Launch F2 Control on the smartphone/tablet.
When F2 Control launches, a Bluetooth device list will appear. Tap the device name/ID to connect
to the F2-BT.
The REC/PLAY LED will light orange on the F2-BT connected to F2 Control.
4. Use F2 Control to operate and set the F2-BT.
NOTE
Connection with F2 Control is not possible when connected to a computer.

10
List of F2 Editor/F2 Control functions
Function Explanation F2 Editor F2 Control
Record/play/stop Control record, play, stop and other operations
Remaining battery charge
display
Check remaining battery charge
Recording/playback file
name display
Check name of file being recorded/played
Elapsed recording time
display
Check elapsed recording time
Recordable time display Check remaining recordable time
Level meter display Check input level (level meter)
Error message display Check error content
Lo Cut Set low-cut function
Output Volume Adjust output volume
Rec Format Select recording format
Rec File Name Set recording file name
User Defined Name Edit text used for file name
Rec File Note Edit note for recording file
Date/Time Set date and time added to recording files
Battery Type Select type of battery
Bluetooth Function Select function to use by Bluetooth
Forget Device End pairing with timecode synchronization device
Auto Power Off Set time until power turns off automatically
Factory Reset Reset to factory default settings
SD Card Format Format microSD card for use
Finder Check files on microSD card
Rename Change names of recorded files
Note Edit notes of recorded files
Version Check version