Zte ZXR10 5900E Series User manual

All Rights reserved, No Spreading abroad without Permission of ZTE
1
ZTE SEC IPv4 instructions

All Rights reserved, No Spreading abroad without Permission of ZTE
2

All Rights reserved, No Spreading abroad without Permission of ZTE
3
Table of Contents
EQUIPMENTS FOR CERTIFICATION......................................................................................................4
TEST INSTRUCTION FOR 5900E ...........................................................................................................5
TEST INSTRUCTION FOR ZXR10 8900 ..................................................................................................9

All Rights reserved, No Spreading abroad without Permission of ZTE
4
Equipments for Certification
The certified equipments are ZTE two types of Switches: ZXR10 5900E and ZXR10 8900 series.
ZXR10 5900E series MPLS Easy-Maintenance switch adopts high-speed ASIC forwarding chips.
It supports complete family of Ethernet protocols, complete L3/MPLS protocols, efficient QOS
priority mechanisms and flexible management mechanisms. Providing high-density GE ports, it
provides the required access and aggregation features of GE interface for IP MAN or campus
networks or IP RAN.
Figure 1 ZXR10 5900E series
ZXR10 8900 series Terabit MPLS routing switches are the latest introduced products by ZTE
with high capacity and performance for the core/aggregation layer of the network. The series has
the following models: ZXR10 8912, 8908,8905 and 8902 among which ZXR10 8912 reaches up
to 2.88Tbps for the bandwidth of the backplane, 1152Gbps switching capacity, 857Mpps packet
forwarding rate. ZXR10 8900 family supports L2/L3/L4 wire speed switching capability, mainly
positioned at the core/aggregation layer of carrier’s IP MAN, campus, e-government and corporate
network.
Figure 2 ZXR10 8900 series

All Rights reserved, No Spreading abroad without Permission of ZTE
5
Test instruction for 5900E
A.DHCP Snooping Configuration Procedure
_ Topology
DHCP server
Fake server
1
2
3
DHCP Ack
DHCP Require
X
_ Setup
Step1: configure vlan
ZXR10(config)#interface gei_1/1
ZXR10(config-gei_1/1)#switch access vlan 100
ZXR10(config-gei_1/1)#exit
ZXR10(config)#interface gei_1/2
ZXR10(config-gei_1/2)#switch access vlan 100
ZXR10(config-gei_1/2)#exit
Step2：Enable dhcp-snooping on global
ZXR10(config)#ip dhcp snooping enable
Step3：Enable DHCP snooping on vlan and assign Uplink port as trusted port
ZXR10(config)#ip dhcp snooping vlan 100
ZXR10(config)#ip dhcp snooping trust gei_1/1

All Rights reserved, No Spreading abroad without Permission of ZTE
6
B. DHCP option82 Configuration Procedure
_ Topology
DHCP server
1
2
DHCP Require
DHCP Option82
_ Setup
Step1 enable DHCP snooping function same as Case A
Step2：enable option 82 on global
ZXR10(config)#ip dhcp snooping information option
C. ARP source check Configuration Procedure
_ Topology
DHCP server
Ip:10.1.1.5
MAC:0017.314c.0001 1
2
Fake ARP Require
IP: 10.1.1.15
MAC:0022.3245.0005
IP:10.1.1.15
MAC:0056.3200.0002
Discard
3
_ Setup
Step1 :Enable DHCP Snooping function same as case A
Step2: Enable ARP inspection on vlan
ZXR10(config)#vlan 100
ZXR10(config-vlan100)#ip arp inspection

All Rights reserved, No Spreading abroad without Permission of ZTE
7
D. IP source check Configuration Procedure
_ Topology
DHCP server
Inlegal host
IP:10.1.1.15 1
2
Legal host
IP:10.1.1.15
Discard
3
_ Setup
Step1:Enable DHCP snooping function same as Case A
Step2: Enable IP Souce guard on port
ZXR10(config-gei_1/2)#ip dhcp snooping ip-source-guard ip-base
E. Static user binding Configuration Procedure
_ Topology
DHCP server
No defined static user
1
2
Static user
Discard
3
_ Setup
Step1：Enable DHCP snooping function same as case A.
Step2: Enable IP Souce guard on port
ZXR10(config-gei_1/2)#ip dhcp snnoping ip-source-guard mac-ip-base
Step3: Configure Static user binding table entry on vlan

All Rights reserved, No Spreading abroad without Permission of ZTE
8
ZXR10(config)#ip dhcp snooping binding 001f.c674.15a8 vlan 10
10.10.40.100 gei_1/3 expiry 3600
F. Port isolation Configuration Procedure
_ Topology
DHCP server
Uer1
1
2
User2
3
No traffic
directly
between Users
_ Setup
Step1: Configure port isolation session on global
ZXR10(config)#vlan private-map session-id 1
isolate gei_1/1, gei_1/3
G. ACLs
The ZTE Series has full support port-based advanced ipv4/ipv6/L2 header
ACLs
The following example describes how to utilize on acl to block inbound
special Source ip address;
_ Topology
DHCP server
1
2
User

All Rights reserved, No Spreading abroad without Permission of ZTE
9
_ Setup
Step1：configure ACL
ZXR10(config)#acl standard number 10
ZXR10(config-std-acl)#rule 1 deny 192.168.1.100 0.0.0.0
Step2：enable ACL on port inbind
ZXR10 (config-fei_1/2)#ip access-group 1 in
Test Instruction for ZXR10 8900
A.DHCP Snooping Configuration Procedure
_ Topology
DHCP server
Fake server
1
2
3
DHCP Ack
DHCP Require
X
_ Setup
Step1: configure vlan
ZXR10(config)#interface gei_1/1
ZXR10(config)#ipv4 protocol-protect mode dhcp enable
ZXR10(config-gei_1/1)#switch access vlan 100

All Rights reserved, No Spreading abroad without Permission of ZTE
10
ZXR10(config-gei_1/1)#exit
ZXR10(config)#interface gei_1/2
ZXR10(config)#ipv4 protocol-protect mode dhcp enable
ZXR10(config-gei_1/2)#switch access vlan 100
ZXR10(config-gei_1/2)#exit
Step2：Enable dhcp-snooping on global
ZXR10(config)#ip dhcp snooping enable
Step3：Enable DHCP snooping on vlan and assign Uplink port as trusted port
ZXR10(config)#ip dhcp snooping vlan 100
ZXR10(config)#ip dhcp snooping trust gei_1/1
B. DHCP option82 Configuration Procedure
_ Topology
DHCP server
1
2
DHCP Require
DHCP Option82
_ Setup
Step1 enable DHCP snooping function same as Case A
Step2：enable option 82 on global
ZXR10(config)#ip dhcp snooping information option
C. ARP source check Configuration Procedure
_ Topology

All Rights reserved, No Spreading abroad without Permission of ZTE
11
DHCP server
Ip:10.1.1.5
MAC:0017.314c.0001 1
2
Fake ARP Require
IP: 10.1.1.15
MAC:0022.3245.0005
IP:10.1.1.15
MAC:0056.3200.0002
Discard
3
_ Setup
Step1 :Enable DHCP Snooping function same as case A
Step2: Enable ARP inspection on vlan
ZXR10(config)#vlan 100
ZXR10(config-vlan100)#ip arp inspection
ZXR10(config)#interface gei_1/1
ZXR10(config-gei_1/1)#ip arp inspection trust
ZXR10(config)#ip arp inspection validate dst-mac
ZXR10(config)#ip arp inspection validate ip
ZXR10(config)#ip arp inspection validate src-mac
D. IP source check Configuration Procedure
_ Topology

All Rights reserved, No Spreading abroad without Permission of ZTE
12
DHCP server
Inlegal host
IP:10.1.1.15 1
2
Legal host
IP:10.1.1.15
Discard
3
_ Setup
Step1:Enable DHCP snooping function same as Case A
Step2: Enable IP Souce guard on port
ZXR10(config-gei_1/2)#ip dhcp snooping ip-source-guard ip-base
E. Static user binding Configuration Procedure
_ Topology
DHCP server
No defined static user
1
2
Static user
Discard
3
_ Setup
Step1：Enable DHCP snooping function same as case A.
Step2: Enable IP Souce guard on port
ZXR10(config-gei_1/2)#ip dhcp snnoping ip-source-guard mac-ip-base
Step3: Configure Static user binding table entry on vlan
ZXR10(config)#ip dhcp snooping binding 001f.c674.15a8 vlan 10
10.10.40.100 gei_1/3 expiry 3600

All Rights reserved, No Spreading abroad without Permission of ZTE
13
F. Port isolation Configuration Procedure
_ Topology
DHCP server
Uer1
1
2
User2
3
No traffic
directly
between Users
_ Setup
Step1: Configure port isolation session on global
ZXR10(config)#vlan private-map session-id 1
isolate gei_1/1, gei_1/3
G. ACLs
The ZTE Series has full support port-based advanced ipv4/ipv6/L2 header
ACLs
The following example describes how to utilize on acl to block inbound
special Source ip address;
_ Topology
DHCP server
1
2
User
_ Setup
Step1：configure ACL

All Rights reserved, No Spreading abroad without Permission of ZTE
14
ZXR10(config)#acl standard number 10
ZXR10(config-std-acl)#rule 1 deny 192.168.1.100 0.0.0.0
Step2：enable ACL on port inbind
ZXR10 (config-fei_1/2)#ip access-group 1 in