Zte CDMA2000 1X EVDO User manual

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
CDMA2000 1X EV-DO
Wireless Data Terminal
User Guide
This User Guide is used for Wireless Data Terminal of AC8710.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
Copyright Statement
Copyright © 2007 by ZTE Corporation
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without the prior
written permission of ZTE Corporation.
ZTE Corporation reserves the right to make modifications on print errors or update specifications
in this manual without prior notice.
V1.0, Nov. 2007

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
Table of Contents
1. Introduction.............................................................................................................................1
2. Precautions..............................................................................................................................1
3. Appearance .............................................................................................................................2
3.1 Introduction.........................................................................................................................2
3.2 Insert R-UIM Card..............................................................................................................2
3.3 Operation Guide of Data Cable...........................................................................................3
4. Install and Uninstall................................................................................................................4
4.1 Windows 2000 ...................................................................................................................5
4.1.1 Install........................................................................................................................5
4.1.2 Uninstall...................................................................................................................9
4.2 Windows XP ....................................................................................................................10
4.2.1 Install......................................................................................................................10
4.2.2 Uninstall.................................................................................................................15
4.3 Windows Vista .................................................................................................................16
4.3.1 Install......................................................................................................................16
4.3.2 Uninstall.................................................................................................................20
4.4 Manually Install Through Other USB Port .......................................................................21
4.4.1 Windows 2000........................................................................................................21
5. Run the Application ..............................................................................................................22
6. Connect/Disconnect..............................................................................................................23
7. Connection Records..............................................................................................................24
8. Voice Call.................................................................................................................................25
9. Call History .............................................................................................................................28
10. Short Message........................................................................................................................29
11. Phone Book............................................................................................................................31
12. Setting....................................................................................................................................33
13. Help .......................................................................................................................................36
14. Connect to the Website..........................................................................................................36
15. Trouble-shooting....................................................................................................................37

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
1. Introduction
Thank you for choosing AC8710 CDMA2000 1X EV-DO Wireless Data Terminal (hereinafter
referred to as Data Terminal) of ZTE Corporation.
The Data Terminal equips with a standard USB interface and supports both CDMA2000 1X
EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing
on the Internet, send&receive short messages, and make&receive phone calls.
2. Precautions
¾Please don’t use the product near flammable or explosive materials because it might cause
failure or fire.
¾Keep the product away from high temperature, humidity, or dust because it might cause
failure.
¾Avoid shock, cast or impact. Please keep the product well when you don’t use it.
¾Do not unplug the antenna. Damage cause by misuse is not covered by this warranty.
¾Don’t use the product near the place where is weak signal or high-precision electronic device
because the magnetic interference might cause the misoperation of electronic device or other
problems.
¾Please make sure to quit the application before pulling out the terminal, otherwise it would
damage the terminal or affect the normal operation of the system.
¾Please don’t insert or pull out the card with great force to avoid damaging the interface.
¾This device has been tested for FCC RF exposure body SAR compliance with typical laptop
computers. In order to comply with FCC RF exposure requirements, AC8710 CDMA data
terminal user is recommended to have good knowledge on RF exposure. During operation,
a 1.5cm separation distance should be maintained between the antenna, whether extended or
retracted, and the user’s/bystander’s body (excluding hands, wrists, feet, and ankles) to
ensure FCC RF exposure compliance.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
3. Appearance
3.1 Introduction
TopView RearView
LED status descriptions:
Network Registered Service available or
Searching for the network
Upon an incoming
call(as the terminal
supports voice call)
LED
Inserting
the data
terminal EV-DO 1X EV-DO 1X EV-DO 1X
Yellow ON OFF Slow Flash OFF Quick Flash OFF Flash
Green ON Slow
Flash OFF Quick Flash OFF Flash OFF
3.2 Insert R-UIM Card
Note: If your data terminal doesn’t need R-UIM card, please skip this section.
1. Pull out the tap；
2. Take out the R-UIM card cover in the direction indicated by the arrow；
USB Interface
Host
Tap
Antenna
LED
R-UIM Card Cover

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
3. Insert R-UIM card as below figure；
4. Push back R-UIM card cover in the direction indicated by the arrow.
3.3 Operation Guide of Data Cable
Generally, the Data Terminal could be directly connected with USB port. You could also connect
the Data Terminal with PC by using the accompanying data cable, as shown in the following
figure. Connect Interface ①with Data Terminal, and interface ②with PC's USB port. If the
power supply from USB port is insufficient, connect both interface ②and ③with USB port
together.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4. Install and Uninstall
System Requirements:
The Data Terminal supports the following operating system:
¾Windows 2000
¾Windows XP
¾Windows Vista
PC minimum configurations:
CPU Pentium-II/233MHz
USB interface 2.0 (USB1.0 and 1.1 compatible)
Optical Drive CD-ROM (for installation only)
Memory 64 MB
Disk Space 50 MB (used for installation of application)

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4.1 Windows 2000
4.1.1 Install
Note: Do not insert the Data Terminal before installation.
1、Find “Setup.exe” firstly in Data Terminal CD-ROM, double-click it to display the Welcome
picture, and then click “Next”;
2、Select the location where you want the program to be installed, and then click “Next”;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
3、Select Start Menu folder, and then click “Next”;
4、When you see the window below, please click “Install”;
5、Please wait for installation.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
6、Please insert the Data Terminal into USB interface if the system prompts you to insert the
hardware (If it has been inserted, please unplug it and insert again.)
7、The system shall find the new hardware and install the driver automatically. Just wait a minute;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
8、The driver is installed successfully. Pleas click “OK”;
9、Click “Finish” to close the last screen of the wizard. Now you can start the application for Data
Terminal.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4.1.2 Uninstall
1、Select Start -> Programs -> ZTE Wireless Terminal -> Uninstall ZTE Wireless Terminal. Click
“Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program.
Click “Yes”;
2、Please wait;
3、Click “OK” when un-installation is completed;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4.2 Windows XP
4.2.1 Install
Note: Do not insert the Data Terminal before installation.
1. Find “setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the
Welcome picture, and then click “Next”;
2. Select the location where you want the program to be installed, and then click “Next”;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
3. Select Start Menu folder, and then click “Next”;
4. When you see the window below, please click “Install”;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
5. Please wait for installation;
6. Please insert the Data Terminal into USB interface if the system prompts you to insert the
hardware; (If it has been inserted, please unplug it and insert again.)

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
7. The system shall find the new hardware and install the driver automatically. Just wait a
minute;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
8. The driver is installed successfully. Pleas click “OK”;
9. Click “Finish” to close the last screen of the wizard. Now you can start the application for
data terminal.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4.2.2 Uninstall
1. Select Start Programs ZTE Wireless Terminal Uninstall ZTE Wireless Terminal. Click
“Uninstall ZTE Wireless Terminal”, and you will be asked if you want to remove the program.
Click “Yes”.
2. Please wait.
3. Click “OK” when un-installation is completed.

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
4.3 Windows Vista
4.3.1 Install
Note: Do not insert the Data Terminal before installation.
1、Find “Setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the Welcome
picture, and then click “Next”;
2、Select the location where you want the program to be installed, and then click “Next”;

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
ZTE Corporation http://www.zte.com.cn
3、Select Start Menu folder, and then click “Next”;
4、When you see the window below, please click “Install”;
5、Please wait for installation;