Zte WF720 User manual

1
WF720
WCDMA/GSM Fixed Wireless Terminal
User Manual

2
Content
Getting to Know Your Device ........................................ 3
Appearance .....................................................................................3
LED Indicator ...................................................................................4
Device Installation.......................................................... 5
Before You Begin .............................................................................5
Installing the SIM Card and the Battery ...........................................5
Installing the Power Adapter............................................................7
Connecting the Device to a Phone ..................................................7
Turning on Your Device....................................................................8
Checking the Wireless Signal ..........................................................8
Using Your Device .......................................................... 9
Making Calls ....................................................................................9
Receiving Calls ................................................................................9
Voice Mail ........................................................................................9
Call Waiting....................................................................................10
Call Forwarding..............................................................................10
Activating Call Forwarding .......................................................10
Deactivating Call Forwarding ................................................... 11
Calling Line Identication Restriction ....................................... 11
3 - Way Calling............................................................................... 11
Adjusting Volume ........................................................................... 11
PIN Lock ........................................................................ 12
Troubleshooting ........................................................... 13
Specication ................................................................. 14
Safety Notes.................................................................. 15
IC Notice........................................................................ 17

3
Getting to Know Your Device
Appearance
NOTE:
Service Port is designed for diagnostic purposes only, not for customer
use. Never place a USB-based device into the USB port of the device
under any circumstance. Doing so may damage the device and negate
its warranty.

4
LED Indicator
The table below describes possible states for each of the
Icon Indicator Status
Signal Strength
Green Solid Strong
Yellow Solid Week
Red Solid No service
Red Blinking Checking SIM card
Battery Charge
Green Solid High (Charging)
Green Blinking High (Using the battery)
Yellow Solid Average (Charging)
Yellow Blinking Average (Using the battery)
Red Solid Low (Charging)
Red Blinking Low (Using battery)
Off No battery connected
Voice Mail Green Blinking New message waiting
Off No new message
Power Solid Green AC power connected
Off AC power disconnected

5
Device Installation
Before You Begin
Your device works exclusively with the ROGERS cellular network and
DOES NOT use your home’s phone wall jacks.
Your device should be located:
Where you have a strong cellular signal from a cell tower, typically
near a window or outside wall.
Near an electrical wall outlet.
Installing the SIM Card and the Battery
1. Remove the cover from the battery compartment.
2. Insert the SIM card in the SIM card slot.

6
3. Insert the battery connection cable into the battery port.
4. Place the battery in the battery slot and replace the battery cover.
NOTES:
The system will stop charging the battery when the ambient tem-
perature is outside of the temperature range allowed for charging
(0 °C ~ 55 °C).
When the power adapter is connected, the battery will automatically
be charged.
When fully charged, the battery will automatically stop charging.
Remove the battery if the device will be unused for a long period.
The battery is intended for backup purposes only (in the event of a
power failure).
The device takes about 5 hours to charge fully. The charge time
may be impacted by environmental factors.

7
Installing the Power Adapter
1. Plug the power adapter into an electrical wall outlet.
2. Insert the small end of the power adapter into the Power port on the
back of your device.
Connecting the Device to a Phone
1. Unplug your phone from the wall jack.
2. Plug your phone into the “Phone 1”port on the WF720, using your
existing phone cable or included phone cable.
IMPORTANT: DO NOT plug the WF720 into a wall jack.

8
NOTE:
The “Phone 2” port can be used to connect an additional phone.
This port uses the same telephone number as the “Phone 1” port.
Put the device at least 2.5 meters away from the connected phone,
TV sets, radio and other electronic devices to avoid electromagnetic
interference.
Turning on Your Device
Press and hold the power button about 8 seconds until the signal
strength light comes on.
Checking the Wireless Signal
1. Raise antenna to an upright position.
2. Conrm signal strength light is green for optimal performance.
NOTE: If there is a yellow light, please change the installation location.

9
Using Your Device
Making Calls
1. Before making a call, make sure that the wireless signal is strong.
2. Lift the handset of your home phone, enter the telephone number
(0~9*#). The number will be dialed automatically.
3. When your call is nished, hang up your home phone or return the
phone to its base to ensure that you can receive calls.
Receiving Calls
When the home phone rings, lift the handset or press Hands-Free to
answer the incoming call.
Voice Mail
The voice mail indicator ( ) will blink green when you have new
voice mail messages.
1. Lift the handset of your home phone and listen for the dial tone.
2. Press 1 to access your voice mail and enter your password.
3. Follow the system prompts to listen to and manage your voice
mails.

10
Call Waiting
If you subscribe the call waiting service with your local telephone ser-
vice provider, you will hear a beep tone if someone calls while you are
already on a call. Press FLASH on the handset to put your current
call on hold and take the new call. You can press FLASH any time to
switch back and forth between calls.
Press the service code on the dial pad of your home phone to enable
or disable the call waiting function per instructions below.
To enable this feature:
1. Pick up the handset and listen for the dial tone.
2. Dial *43# to enable this function and you will hear a conrmation
tone.
3. Hang up your home phone or return the phone to its base.
To disable this feature:
1. Pick up the handset and listen for the dial tone.
2. Dial #43# to disable this function and you will hear a conrmation
tone.
3. Hang up your home phone or return the phone to its base.
Call Forwarding
If you subscribe to the Call Forwarding feature, you can forward the
calls to another phone number. Your home phone will not ring until you
deactivate the service.
Activating Call Forwarding
1. Pick up the handset and listen for the dial tone.
2. Dial *21*phone number# to enable this function and you will hear
a conrmation tone.
Tip: The phone number is that you want the calls to be forwarded to (e.g.
*21*1234567890#).
3. Hang up your home phone or return the phone to its base.